An Experimental Investigation on the Air Permeability of Passive Ventilation Grilles

Abstract The need of increasing both energy saving and acoustic insulation has leaded to the design of lowest air permeability frames resulting in the worsening of indoor air quality. Moreover, sometime in several civil-use existing buildings (i.e. schools or houses, historical buildings) mechanical ventilation systems cannot be installed due to non-removable constraints. In these cases, passive ventilation grilles are a cheap and effective solution for the ventilation. This work deals with an in-depth experimental analysis about the air permeability values measured over a set of passive ventilation grilles available on the market. Obtained results often showed performances very far to those declared. This is not due to multiplicity of involved parameters affecting their behaviour rather to a lack of standardized test methods

Influence of Installation Conditions on Heating Bodies Thermal Output: Preliminary Experimental Results☆

Abstract Heating bodies are thermodynamic systems whose heat output is strongly dependent on boundary conditions and in about a century several attempts have been made for its experimental determination. To this aim, at the beginning of 60s, in Europe different national standards were adopted (e.g. in 1967 in Italy the UNI 6514/1967). At European level, the EN 442-1:2014 and EN 442-2:2014 allows the heating body heat output estimation with an expanded uncertainty lower than 1% and they are now accepted in various international markets. The EN 442 also allows heat output calculation in operating conditions different from standard ones by employing theoretical-experimental correlations that, by their nature, are not able to include any possible actual operating condition. In fact, in actual operating conditions the heating body heat output depends on several factors, among which: i) installation position with respect to the wall and the floor; ii) presence grid/shelf/niche or an obstruction caused by curtains on the heating body; iii) thermo-fluid-dynamic condition variations (inlet flow rate and temperature); iv) hydraulic connections. Radiators represent the most spread heating body (installed since the end of '800) and in the last decades different radiators typologies have been proposed on the market, characterized by different materials, sizes, shapes, etc. In the present paper the authors present the preliminary result of an experimental campaign on field for the heat output measurement of different radiators typologies (cast iron, aluminum) as a function of different installation and operating conditions. The influence on the heating body performance and the associate technical-economical consequences in terms of heat cost allocation accuracy have been investigated

Potential for building Façade-integrated solar thermal collectors in a highly urbanized context

Development of technologies, materials, support systems, and coatings has made the integration of solar thermal systems into the building envelope increasingly possible. Solar thermal collectors can either be directly integrated, substituting conventional roof or façade covering materials, or constitute independent devices added to a roof or façade structure. Aimed at estimating the real effectiveness of building-integrated solar systems for domestic heat water (DHW) production or for heating integration, when horizontal or inclined pitches on buildings are not applicable, the authors analyze a case study with different scenarios, taking into account the issues connected to a highly urbanized context in the Mediterranean climate. A GIS model was used for estimating the energy balance, while the real producibility of the simulated systems was calculated by a dynamic hourly simulation model, realized according to ISO 52016. The savings in terms of primary energy needs obtained by installing solar thermal systems on the facade are presented, and the differences between the cases in which the system is used for DHW production only and for space heating too are distinguished and discussed. The evaluated potential is quantified in the absence of roof collectors, despite their high potential in the Mediterranean region, in order to better appreciate the effects induced by integrated facade systems

Individual metering and submetering for cooling application

In 2012 the Energy Efficiency Directive (EED) has set mandatory installation of individual metering and submetering systems for accounting thermal energy consumption in buildings where centralized heating/cooling sources are present, when technically feasible and cost efficient. As a consequence, direct thermal energy meters or indirect heat accounting systems have spread widely in residential buildings, for metering and sub-metering in space heating applications. On the other hand, individual metering of thermal energy in space cooling is a difficult task, due to the very different types of cooling systems and to the lack of technical and legal metrology regulation. In this paper possible solutions available for direct metering and submetering of different types of centralized cooling systems are discussed. Indeed, for direct metering application, the cooling fluid flow metering is a particularly crucial issue due to small pipe diameters and different fluid properties. Thus, the authors carried out an experimental comparison between a Coriolis flow-meter and an ultrasonic clamp-on flow-meter in the cooling fluid circuit of a direct expansion system. Tests have been performed at different operative temperature differences between flow and return, showing relative errors within ± 10%

A novel measurement method for accurate heat accounting in historical buildings

Nowadays, two different heat accounting methods are available: the direct method, based on heat meters, and the indirect one, based on heat cost allocators. Unfortunately, in existing buildings, due to the plant configuration, heat meters are often technically unfeasible or not cost efficient, whereas heat cost allocators can be easily installed in almost all conditions. At the same time, the indirect method relies on a high number of interconnected devices with installation and operative conditions often variable within the same building and influencing the on-field metrological performances. In this paper, the authors propose a novel "hybrid" method for accurate heat accounting combining the advantages of indirect method with the higher accuracy typical of direct methods. The proposed method has been experimented at INRIM, the primary metrology institute in Italy, assessing the on-field performance in a virtual eight-apartments building. The experimental results show that the proposed method always presents improved accuracy. (C) 2020 Elsevier Ltd. All rights reserved

An innovative method for the thermal conductance measurement of windows

Paper presented at the 5th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics, South Africa, 1-4 July, 2007.One of the most important contributions to the energy requirements in buildings is due to heat transfer through the window surfaces. Therefore, several efforts were made in order to obtain new window frames and glass assemblies with low thermal heat transfer characteristics. To this point of view, it is also necessary to reach accurate measurements of the abovementioned parameters. In this paper, the authors show an innovative measurement method based on radiative and conductive heat transfer which performs window thermal conductance measurements with annexed uncertainty budget evaluation. In the design of the experimental apparatus the authors used a 3D finite volume software whose results were useful for the system optimisation and characterisation.cs201

Estimating the smart readiness indicator in the italian residential building stock in different scenarios

The Energy Performance of Buildings Directive 2018/844/EU introduced the smart readiness indicator (SRI) to provide a framework to evaluate and promote building smartness in Europe. In order to establish a methodological framework for the SRI calculation, two technical studies were launched, at the end of which a consolidated methodology to calculate the SRI of a building basing on a flexible and modular multicriteria assessment has been proposed. In this paper the authors applied the above-mentioned methodology to estimate the SRI of the Italian residential building stock in different scenarios. To this end, eight “smart building typologies”, representative of the Italian residential building stock, have been identified. For each smart building typology, the SRI was calculated in three scenarios: (a) base scenario (building stock as it is); (b) an “energy scenario” (simple energy retrofit) and (c) a “smart energy scenario” (energy retrofit from a smart perspective). It was therefore possible to estimate a national average SRI value of 5.0%, 15.7%, and 27.5% in the three above defined scenarios, respectively