153 research outputs found
Method for evaluating the durability of aircraft piston engines
A significant issue in aircraft engines is quantifying residual life to overhaul. The algorithm described in this paper calculates with a good level of reliability the residual life of a petrol piston engine. The method was tested on small, latest-generation, naturally-aspirated aircraft and racing piston engines, and has been effective in several experiments. This method is implemented directly on the electronic control system of the engine with very few lines of C-code. The method can also be used in many industrial engines. This innovative method assumes that only two main factors (power level and wear) affect engine durability or time between overhauls. These two factors are considered as separate and combined with worst case criteria. The wear is assumed to follow a logarithmic law and a formula similar to the Miner’s law for material fatigue is used, making it possible to calculate the power-level curve with knowledge of only two points. The wear-curve is also related to elapsed engine cycles. The algorithm is very simple and can be implemented with just a few lines of software code accessing data collected from existing sensors. The system is currently used to evaluate actual residual life of racing engines
Revised KAD Tool To Optimize F1 Cars Through A Combined-Elitarian Genetic-Fuzzy Algorithm
The KAD(Knowledge Aided Design) tool is developed to predict the performance of an F1 car in different driving conditions and with different configurations. The regulations to put in trimming a car, also in the exasperated technology of the competitions, still demand a remarkable dose of luck and an elevated number of tests. It is then important to know a set of regulations close to the optimal trim before testing the car on the track. The difficult phase of this process is to evaluate the lap time. As a matter of fact driving style, track conditions and car behavior should be simulated. The optimisation of the fuzzy controller that simulates the pilot for an F1 racing car is difficult due to handling problems
and velocity of response. For this purpose a specific Genetic Algorithm (GA) was conceived and tuned to work with a lumped mass model of an F1 racing car for the optimization of the fuzzy controller that simulates the pilot. A new mutation and a new crossover operator were defined to complement the standard crossover and mutation operators of the basic Holland\u2019s GA. This was necessary in order to increase the overall performance of the fuzzy pilot. This approach was tested on an F1 car due to the huge amount of data available (Donnarumma, 1998; Moelenbein, 1989; Lee and Takagi, 1993)
On the Avant-Garde IDeS Method for the Future of Car Design Applied to an SUV Project
This case study aims to develop a new innovative SUV (Sport Utility Vehicle) model exploiting IDeS (Industrial Design Structure), which is an engineering approach conceived to optimize car design projects in the automotive industry like never before. A compact SUV was chosen because it is a type of vehicle that is highly requested by customers, and it is extremely successful in the market due to its versatility. In fact, compact SUVs are mixed vehicles that combine the pragmatism of a car with the typical robustness of an off-road vehicle making them suitable both for urban and off-road scenarios. The following pages will illustrate the steps followed for the realization of the final product using the SDE (Stylistic Design Engineering) method and other various design technologies, such as Quality Function Deployment (QFD), Benchmarking (BM) and Top Flop Analysis (TPA). In the final part of this project, the virtual prototyping of the product is carried out using Additive Manufacturing (AM) with an FDM 3D printer. The combination of these methods forms, to all intents and purposes, the IDeS, a newly developed innovative and cutting-edge discipline capable of schematically guiding the new product development process in companies with unprecedented efficiency
Recommended from our members
Grid computing technologies for renewable electricity generator monitoring and control
In this paper we discuss the use of real-time Grid computing for the monitoring, control and simulation of renewable electricity generators and their associated electrical networks. We discuss briefly the architectural design of GRIDCC and how we have integrated a number of real (solar, CHP) and simulated conventional power generators into the GRIDCC environment. A local weather station has also been attached to an Instrument Manager to alert experts appropriately when the Solar Array is not generating. The customised remote control and monitoring environment (a virtual control room), distributed using a standard web server, is discussed
Developing innovative crutch using IDeS (industrial design structure) methodology
The present study wants to bring to light a new type of crutch designed for a chronic patient with perennial limited mobility, who must use this support every time a move is needed. The main purpose of the project consists in recommending a correct use of the crutch through technology, limiting the damage normally caused by a bad use of crutches and giving a support both for the patient and for the doctor. All of the features of the crutches were defined through relationship matrices and a benchmarking, which helped us for defining the requirements; other important features were defined, taking a look to the technological progresses applied to new, patented crutches. The result is a sensorized crutch, functional and oriented to meet the user's needs in order to prevent an incorrect use of the support avoiding the growth of other pains
Representative volume element (Rve) analysis for mechanical characterization of fused deposition modeled components
Additive manufacturing processes have evolved considerably in the past years, growing into a wide range of products through the use of different materials depending on its application sectors. Nevertheless, the fused deposition modelling (FDM) technique has proven to be an eco-nomically feasible process turning additive manufacture technologies from consumer production into a mainstream manufacturing technique. Current advances in the finite element method (FEM) and the computer-aided engineering (CAE) technology are unable to study three-dimensional (3D) printed models, since the final result is highly dependent on processing and environment parame-ters. Because of that, an in-depth understanding of the printed geometrical mesostructure is needed to extend FEM applications. This study aims to generate a homogeneous structural element that accurately represents the behavior of FDM-processed materials, by means of a representative volume element (RVE). The homogenization summarizes the main mechanical characteristics of the actual 3D printed structure, opening new analysis and optimization procedures. Moreover, the linear RVE results can be used to further analyze the in-deep behavior of the FDM unit cell. Therefore, industries could perform a feasible engineering analysis of the final printed elements, allowing the FDM technology to become a mainstream, low-cost manufacturing process in the near future
Paediatric orthopaedic surgery with 3D printing: Improvements and cost reduction
This paper presents a a novel alghorithm of diagnosis and treatment of rigid flatfoot due to tarsal coalition. It introduces a workflow based on 3D printed models, that ensures more efficiency, not only by reducing costs and time, but also by improving procedures in the preoperative clinical phase. Since this paper concerns the development of a new methodology that integrates both engineering and medical fields, it highlights symmetry. An economic comparison is made between the traditional method and the innovative one; the results demonstrate a reduction in costs with the latter. The current, traditional method faces critical issues in diagnosing the pathologies of a limb (such as the foot) and taking decisions for further treatment of the same limb. The proposed alternative methodology thus uses new technologies that are part of the traditional workflow, only replacing the most obsolete ones. In fact, it is increasingly becoming necessary to introduce new technologies in orthopedics, as in other areas of medicine, to offer improved healthcare services for patients. Similar clinical treatments can be performed using the aforementioned technologies, offering greater effectiveness, more simplicity of approach, shorter times, and lower costs. An important technology that fits into this proposed methodology is 3D printing
Optic pathway glioma in type 1 neurofibromatosis: Review of its pathogenesis, diagnostic assessment, and treatment recommendations
Type 1 neurofibromatosis (NF1) is a dominantly inherited condition predisposing to tumor development. Optic pathway glioma (OPG) is the most frequent central nervous system tumor in children with NF1, affecting approximately 15-20% of patients. The lack of well-established prognostic markers and the wide clinical variability with respect to tumor progression and visual outcome make the clinical management of these tumors challenging, with significant differences among distinct centers. We reviewed published articles on OPG diagnostic protocol, follow-up and treatment in NF1. Cohorts of NF1 children with OPG reported in the literature and patients prospectively collected in our center were analyzed with regard to clinical data, tumor anatomical site, diagnostic workflow, treatment and outcome. In addition, we discussed the recent findings on the pathophysiology of OPG development in NF1. This review provides a comprehensive overview about the clinical management of NF1-associated OPG, focusing on the most recent advances from preclinical studies with genetically engineered models and the ongoing clinical trials
New methodology for diagnosis of orthopedic diseases through additive manufacturing models
Our purpose is to develop the preoperative diagnosis stage for orthopedic surgical treatments using additive manufacturing technology. Our methods involve fast implementations of an additive manufactured bone model, converted from CAT data, through appropriate software use. Then, additive manufacturing of the formed surfaces through special 3D-printers. With the structural model redesigned and printed in three dimensions, the surgeon is able to look at the printed bone and he can handle it because the model perfectly reproduces the real one upon which he will operate. We found that additive manufacturing models can precisely characterize the anatomical structures of fractures or lesions. The studied practice helps the surgeon to provide a complete preoperative valuation and a correct surgery, with minimized duration and risks. This structural model is also an effective device for communication between doctor and patient
GD (Generative design) applied to a plastics recovery drone (PRD) using IDeS (industrial design structure)
The evolution of innovative and systematic design methodologies over time has widened the design concept involvement from the product development phase, which also includes the production and start-up phases. Literature findings have presented to accomplish a Generative Design (GD) approach through the application of an innovative method called Industrial Structure Design (IDeS), a systematic design method able to discover the customer’s needs and the fundamental technical solutions to obtain a good innovative product, involving the whole organization for this achievement. Nevertheless, there is a social demand for solutions to the dramatic and growing problem of marine pollution from plastic materials, encouraging the designers to conceive a new innovative drone for waste collection at sea. Therefore, this study aims to merge all the most advanced design technologies with IDeS in an integrated way, by generating a structure that can also be adopted to plan the organization of a production company. The approach is validated with the design of the Recovery Plastic Drone (RPD) obtained with the IDeS methodology, combining Design and Product development phases, leading to a better and innovative solution for the market
- …