Effect of graphene vs. reduced graphene oxide in gold nanoparticles for optical biosensors: a comparative study

Aiming to develop a nanoparticle-based optical biosensor using gold nanoparticles (AuNPs) synthesized using green methods and supported by carbon-based nanomaterials, we studied the role of carbon derivatives in promoting AuNPs localized surface plasmon resonance (LSPR), as well as their morphology, dispersion, and stability. Carbon derivatives are expected to work as immobilization platforms for AuNPs, improving their analytical performance. Gold nanoparticles (AuNPs) were prepared using an eco-friendly approach in a single step by reduction of HAuCl4·3H2O using phytochemicals (from tea) which act as both reducing and capping agents. UV–Vis spectroscopy, transmission electron microscopy (TEM), zeta potential (ζ-potential), and X-ray photoelectron spectroscopy (XPS) were used to characterize the AuNPs and nanocomposites. The addition of reduced graphene oxide (rGO) resulted in greater dispersion of AuNPs on the rGO surface compared with carbon-based nanomaterials used as a support. Differences in morphology due to the nature of the carbon support were observed and are discussed here. AuNPs/rGO seem to be the most promising candidates for the development of LSPR biosensors among the three composites we studied (AuNPs/G, AuNPs/GO, and AuNPs/rGO). Simulations based on the Mie scattering theory have been used to outline the effect of the phytochemicals on LSPR, showing that when the presence of the residuals is limited to the formation of a thin capping layer, the quality of the plasmonic resonance is not affected. A further discussion of the application framework is presented.info:eu-repo/semantics/publishedVersio

Chemical Modification of Semiconductor Surfaces by Means of Nanometric Cellulose Films

Cellulose films of nanometric thickness were produced by spin-coating on GaAs(100). Films were deposited using cellulose silylated solutions and subsequently regenerated by exposing them to vapors of hydrochloric acid. After regeneration, these films can strongly resist solvents. Modification of the film surface region was performed by immersing the regenerated cellulose films in a solution of phenyl isocyanate in dimethyl sulfoxide. A different functionalization was also successfully achieved through the interaction of the film surface with 4,4′-methylenebis(phenyl isocyanate) (MDI). Surfaces treated with MDI keep an unreacted isocyanate group and can again be modified by amines. For this purpose, 4-bromoaniline was used. All kinetics of the different molecular interactions with the cellulose film on GaAs were followed in situ using FTIRS in ATR/MIR (attenuated total reflection in multiple internal reflections) mode. Besides ATR/MIR having an analysis depth on the order of 1 µm, other surface techniques were used for analyzing these films with other probing depths such as X-ray photoelectron spectroscopy with ∼10 nm and high-resolution electron energy loss spectroscopy with ∼1 nm in the impact regime. The set of methods presented here represents a quite adequate way to study the surface chemistry of cellulose films and the procedures for their functionalization

Optimization of HDPE direct fluorination conditions by XPS studies

Abstract A fluorination reactor was designed and built in the laboratory. The optimal conditions of fluorination within the reactor were selected by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) analysis of fluorinated surfaces of a film and a plaque of pure high-density polyethylene (HDPE). This reactor was used to post-mould fluorinate plaques and films of a range of mixtures of virgin and recycled HDPE with and without (re)introduction of additives. The ability to be fluorinated has shown no dependence on the composition virgin/recycled HDPE. Comparison of in-line and post-mould fluorinated samples showed that fluorine concentration profile in depth is thinner in the in-line fluorinated sample when compared with the post-mould fluorinated sample, though the fluorination degree in the extreme surface is larger in the in-line fluorinated sample. This is attributed to a migration of lower surface energy chain blocks towards the surface in the material at high temperatures, which is the case in the in-line fluorination, hindered in the post-mould fluorination where maximum temperature is below the melting point to keep the macroscopic shape. The additives played a minor role in the ability of the surface to be fluorinated.

Valorisation of spent tire rubber as carbon adsorbents for Pb(II) and W(VI) in the framework of a Circular Economy

Open access funding provided by FCT|FCCN (b-on). This work was funded by (a) Valorpneu S.A. through the INOV.AÇÃO 2018 Award; Associate Laboratory i4HB (LA/P/0140/2020); Maria Bernardo thanks FCT (Fundação para a Ciência e Tecnologia) for funding through program DL 57/2016 – Norma transitória. A.M. Ferraria thanks Instituto Superior Técnico for Scientific Employment contract IST-ID/131/2018. This work was also financially supported by GREENERING COST Action CA18224.Spent tire rubber-derived chars and their corresponding H3PO4 and CO2-activated chars were used as adsorbents in the recovery of Pb(II) ion and (W(VI)) oxyanion from synthetic solutions. The developed chars (both raw and activated) were thoroughly characterized to have insight about their textural and surface chemistry properties. H3PO4-activated chars presented lower surface areas than the raw chars and an acidic surface chemistry which affected the performance of these samples as they showed the lowest removals of the metallic ions. On the other hand, CO2-activated chars presented increased surface areas and increased mineral content compared to the raw chars, having presented higher uptake capacities for both Pb(II) (103–116 mg/g) and W(VI) (27–31 mg/g) ions. Cation exchange with Ca, Mg and Zn ions was appointed as a mechanism for Pb removal, as well as surface precipitation in the form of hydrocerussite (Pb3(CO3)2(OH)2). W(VI) adsorption might have been ruled by strong electrostatic attractions between the negatively charged tungstate species and the highly positively charged carbons’ surface. The results shown in this work allow concluding that the valorisation of spent tire rubber through pyrolysis and the subsequent activation of the obtained chars is an alternative and a feasible option to generate adsorbent materials with a high uptake capacity of critical metallic elements.publishersversionepub_ahead_of_prin

Ultrasound and radiation-induced catalytic oxidation of 1-phenylethanol to acetophenone with iron-containing particulate catalysts

Este trabalho foi financiado pelo Concurso Anual para Projetos de Investigação, Desenvolvimento, Inovação e Criação Artística (IDI&CA) 2019 do Instituto Politécnico de Lisboa. Código de referência IPL/2019/STREAM_ISELIron-containingparticulatecatalystsof0.1–1 µmsizewerepreparedbywetandball-milling procedures from common salts and characterized by FTIR, TGA, UV-Vis, PXRD, FEG-SEM, and XPS analyses. It was found that when the wet method was used, semi-spherical magnetic nanoparticles were formed, whereas the mechanochemical method resulted in the formation of nonmagnetic microscale needles and rectangles. Catalytic activity of the prepared materials in the oxidation of 1-phenylethanol to acetophenone was assessed under conventional heating, microwave (MW) irradiation, ultrasound (US), and oscillating magnetic field of high frequency (induction heating). In general, the catalysts obtained by wet methods exhibit lower activities, whereas the materials prepared by ball milling afford better acetophenone yields (up to 83%). A significant increase in yield (up to 4 times) was observed under the induction heating if compared to conventional heating. The study demonstrated that MW, US irradiations, and induction heating may have great potential as alternative ways to activate the catalytic system for alcohol oxidation. The possibility of the synthesized material to be magnetically recoverable has been also verified.info:eu-repo/semantics/publishedVersio

Novel organotin-PTA complexes supported on mesoporous carbon materials as recyclable catalysts for solvent-free cyanosilylation of aldehydes

The work was also funded by national funds through FCT, under the Scientific Employment Stimulus-Institutional Call (CEEC-INST/00102/2018). AGM is grateful to Associação do Instituto Superior Técnico para a Investigação e Desenvolvimento ( IST-ID ) for his post-doctoral fellowship through grant no. BL133/2021-IST-ID . AP and AMF are grateful to FCT and Instituto Superior Técnico (IST), Portugal through DL/57/2017 (Contract no. IST-ID/197/2019 and IST-ID/131/2018). This publication is also supported by the RUDN University Strategic Academic Leadership Program (recipient AJLP, preparation). The authors also acknowledge the Portuguese NMR Network (IST-UL Centre) for access to the NMR facility. Publisher Copyright: © 2023 Elsevier B.V.New organotin compounds with general formula [(PTA-CH2-C6H4-p-COO)SnR3]Br (where R is Me for 3 and Ph for 4; PTA = 1,3,5-triaza-7-phosphaadamantane), bearing the methylene benzoate PTA derivative, were synthesized through a mild two-step process. The compounds were characterized by Fourier transform infrared spectroscopy, electrospray ionization mass spectrometry, elemental analysis and nuclear magnetic resonance spectroscopy (NMR). They were heterogenized on commercially available activated carbon (AC) and multi-walled carbon nanotubes (CNT), as well as on their chemically modified analogues. The obtained materials were characterized by scanning electron microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy. Complex 3 supported on activated carbon (3-AC) was found to be an active and recyclable catalyst for the cyanosilylation of several aromatic and aliphatic aldehydes. Using 3-AC with a low loading of 0.1 mol% several substrates were quantitatively converted, within just 5 min at 50 °C and under microwave irradiation in solvent-free conditions. Multinuclear NMR analysis suggested a mechanism that potentially involves a double activation process, where the nucleophilic phosphorus at the PTA derivative acts as a Lewis base and the Sn(IV) metal centre as a Lewis acid.publishersversionpublishe

Silver Nanoparticles on Cellulose Surfaces: Quantitative Measurements

In this work, cellulose films pre-activated with carbonyldiimidazole (CDI) and grafted with 1,6-hexanediamine, were decorated with silver nanoparticles (AgNPs). The generation of AgNPs was followed by quartz crystal microbalance (QCM). The obtained films were characterized by X-Ray Photoelectron Spectroscopy (XPS) and imaged by atomic force microscopy (AFM). XPS confirmed the synthesis in situ of AgNPs on the film attesting their oxidation state. The results from the three techniques were compared showing how sound the quantitative treatment of the results issued from these techniques can be. The main objective of this work is exactly to show that the quantitative exploration of the results of different characterization techniques can and should be practiced systematically instead of just comparing them qualitatively

Comparison of microwave and mechanochemical energy inputs in the catalytic oxidation of cyclohexane

Este trabalho foi financiado pelo Concurso Anual para Projetos de Investigação, Desenvolvimento, Inovação e Criação Artística (IDI&CA) 2016 do Instituto Politécnico de Lisboa. Código de referência IPL/2016/MechSynCat_ISELThe effect of microwave and mechanochemical ball milling energy inputs was studied for the peroxidative oxidation (with aqueous H2O2) of cyclohexane to cyclohexanol and cyclohexanone, over CoCl2 and/or V2O5 dispersed (μm scale) catalysts. A maximum total yield of cyclohexanol and cyclohexanone of 43% after 1 h of reaction at 30 °C, in acetonitrile and under microwave irradiation (5 W), was achieved over the CoCl2–V2O5 (3 : 1) catalyst prepared by ball milling. Cyclohexanol is the main final product with a selectivity of up to 93% over cyclohexanone. Conducting the oxidation reaction under microwave irradiation under the same conditions but without any mechanochemical treatment of the catalyst prior to use resulted in a lower total yield of 30% with a lower selectivity (69%) towards cyclohexanol over cyclohexanone. The sole application of mechanochemical treatment for the catalyst preparation and the catalytic oxidation of cyclohexane allowed to reach yields of 29% after 1 h of reaction, at room temperature, without microwave irradiation and any additive and in the absence of any organic solvent. Ball milling is shown to provide a convenient, solvent-free method to disperse these solid catalysts and to promote the above cyclohexane oxidation, although, in the latter case, not so effectively as microwave irradiation.info:eu-repo/semantics/publishedVersio