13 research outputs found
Continuous extrusion of a commercially pure titanium powder via the Conform process
It is shown for the first time that cold commercially pure titanium powder can be extruded through a standard Conform machine into fully dense wire with a fine recrystallised microstructure. The grain size has been shown to decrease with increasing wheel speed with an associated increase in tensile strength. The macrostructure of the wire extrudate exhibits a characteristic flow pattern with several regions defined by differences in average grain size and distribution. Finite-element modelling of the process shows the formation of the characteristic macrostructure from powder fed Conform. The process is continuous, utilises standard equipment and does not require powder preheating or inert gas shrouding providing a footing for a true cost reduction in longsection titanium mill product
XCT Analysis of the Influence of Melt Strategies on Defect Population in Ti-6Al-4V Components Manufactured by Selective Electron Beam Melting
Dimensional accuracy of Electron Beam Melting (EBM) additive manufacture with regard to weight optimized truss structures
The Electron Beam (EBM) additive manufacturing process is well suited to fabricating complex structural designs in Tiâ6Alâ4V because of the design freedoms it offers combined with strong and consistent material properties. However it has been observed that complications may arise when manufacturing truss-like structures (such as those produced via structural topology optimization) in the form of undersized features on the finished part. The issue appears to affect truss members that are not aligned with the vertical build direction, with an apparent lack of material on the negative surfaces. This effect appears to worsen with a greater angle between the truss member and the build direction, even with the use of support structures. This investigation has characterized and measured the dimensional errors that result from this issue through 3D scanning techniques. Process modifications have then been made which result in significant improvements in dimensional accuracy. This investigation highlights the importance of heat management at features with negative surfaces to yield parts that are dimensionally accurate without introducing excessive internal melt defects in the form of voids and porosity
The effect of density and feature size on mechanical properties of isostructural metaffic foams produced by additive manufacturing
Simple models describing the relationship between basic mechanical properties and the relative density of various types of porous metals (such as foams, sponges and lattice structures) are well established. Carefully evaluating these relationships experimentally is challenging, however, because of the stochastic structure of foams and the fact that it is difficult to systematically isolate density changes from variations in other factors, such as pore size and pore distribution. Here a new method for producing systematic sets of stochastic foams is employed based on electron beam melting (EBM) additive manufacturing (AM). To create idealised structures, structural blueprints were reverse-engineered by inverting X-ray computed tomographs of a randomly packed bed of glass beads. This three-dimensional structure was then modified by computer to create five foams of different relative density Ïr, but otherwise consistent structure. Yield strength and Youngâs modulus have been evaluated in compression tests and compared to existing models for foams. A power of 3 rather than a squared dependence of stiffness on relative density is found, which agrees with a recent model derived for replicated foams. A similar power of 3 relation was found for yield strength. Further analysis of the strength of nominally fully dense rods of different diameters built by EBM AM suggest that surface defects mean that the minimum size of features that can be created by EBM with similar strengths to machined samples is âŒ1 mm
Application of layout optimization to the design of additively manufactured metallic components
Additive manufacturing (â3D printingâ) techniques provide engineers with unprecedented design freedoms, opening up the possibility for stronger and lighter component designs. In this paper âlayout optimizationâ is used to provide a reference volume and to identify potential design topologies for a given component, providing a useful alternative to continuum based topology optimization approaches (which normally require labour intensive post-processing in order to realise a practical component). Here simple rules are used to automatically transform a line structure layout into a 3D continuum. Two examples are considered: (i) a simple beam component subject to three-point bending; (ii) a more complex air-brake hinge component, designed for the Bloodhound supersonic car. These components were successfully additively manufactured using titanium Ti-6Al-4V, using the Electron Beam Melting (EBM) process. Also, to verify the efficacy of the process and the mechanical performance of the fabricated specimens, a total of 12 beam samples were load tested to failure, demonstrating that the target design load could successfully be met
Spark plasma sintering of commercial and development titanium alloy powders
Emerging lower cost titanium metal powder produced via an electrolytic method has been fully consolidated using spark plasma sintering (SPS) generating microstructures comparable to those observed in Tiâ6Alâ4V PM product. This is the first time powder from an alternative titanium extraction method has been processed via SPS and it is benchmarked with commercial alloys (CPâTi, Tiâ6Alâ4V, and Tiâ5Alâ5Vâ5Moâ3Cr). The effect of powder feedstock size, morphology, and alloy chemistry on the consolidated density and microstructure is presented. Through a design of experiments (DoE) type approach the effect of SPS processing conditions on these alloy powders, including maximum sintering temperature, pressure, heating rate, and dwell time were investigated. The SPS process is found to be largely insensitive to feedstock size and morphology, although very large or highly porous powder particles are more difficult to fully consolidate. The maximum sintering temperature and pressure have the largest contribution to achieving full consolidation, with higher pressures and temperatures increasing the final density. Increasing heating rate increases the final grain size, despite less time being spent at the higher temperature and it is thought this is due to bypassing the traditional first phase of sintering. This paper shows that SPS is a viable step for a low-cost manufacturing route, for example to produce preform billets to be finished with a one-step forging operation, especially when combined with the possibility of lower cost powder. In the long-term, SPS will allow a significant reduction in the processing cost, contributing to an increased usage of titanium powder feedstock for a range of applications. This is reinforced by the successful large scale production of a 5 kg SPS Ti-6-4 billet, demonstrating the potential industrial scalability of the process, particularly for the aerospace industry
X-ray computed tomography characterisation of titanium powders for additive manufacturing
Investigating a Semi-Solid Processing technique using metal powder bed Additive Manufacturing Processes
The work reported investigates in-situ alloying using a semi-solid processing technique with metal powder bed Additive Manufacturing (AM); in this instance Selective Laser Melting (SLM) and Electron Beam Melting (EBM) were employed. This technique utilised customised powder blends that were processed at elevated temperatures. The selection of processing temperature considered specific alloy solidification ranges. As a result, parts with reduced residual stresses can be produced. In addition, the use of customised powder blends explored the feasibility of developing alloys specific to the process/application, thus increasing available material ranges for AM metal powder bed processes
Benchmarking metal powder bed Additive Manufacturing processes (SLM and EBM) to build flat overhanging geometries without supports
Metal powder Additive Manufacturing (AM) allows complex parts to be build from commercial materials. Several industries such as automotive, aerospace and medical have interests in using these technologies. However in metal powder AM, supports/ anchors are required to be melted in place to avoid process failure due to upward warping of flat overhanging geometries. This leads to additional melting of materials, processing time and thus increasing costs of parts build. A series of experiments were conducted to understand capability of processes such as Selective Laser Melting (SLM) and Electron Beam Melting (EBM) to build flat overhang geometries. In addition, effect of preheating the powder feedstock was also performed