4,239 research outputs found
Acylsulfonamide safety-catch linker : promise and limitations for solid-phase oligosaccharide synthesis
Safety-catch linkers are useful for solid-phase oligosaccharide synthesis as they are orthogonal to many common protective groups. A new acylsulfonamide safety-catch linker was designed, synthesized and employed during glycosylations using an automated carbohydrate synthesizer. The analysis of the cleavage products revealed shortcomings for oligosaccharide synthesis
Leaf Pubescence: The Significance of Lower Surface Hairs for the Spectral Properties of the Upper Surface
The fraction of the global radiation incident on the upper surface of leaves of Tussilago farfara L. which is reflected, varies according to the presence or absence of hairs on the lower surface. Calculations of the radiation fluxes at 550 and 1000 nm wavelengths prove that these differences arise from a partial reflection of the radiation emerging from the lower epidermis by the hair cove
Transpiration and water uptake of Senecio medley-woodii and Aloe jucunda under changing environmental conditions: measurements with a potometric water-budget-meter
Transpiration, water uptake by the roots and CO2 exchange of two leaf succulents, Senecio medleywoodii (Asteraceae) and Aloe jucunda (Asphodeliaceae), were monitored simultaneously and continuously with a gas exchange cuvette combined with an apparatus to quantify water uptake (= waterbudget- meter). Measurements, which are primarily valid for plants with a sufficient water supply, were made with the same plant for up to 29 consecutive days. Ambient air temperature varied between 17 and 35 °C with a constant dewpoint temperature of 13°C of the ambient air and a 12 h photoperiod at 400-500µmol m−2s−1 photon irradiance. The net water flux (Jw(net)=water uptake-transpiration) and the water balance (Jw(net) integrated for a timespan) were calculated. Various tests were made to determine the accuracy of the measurements made with this rather complex equipment. In most cases the errors for transpiration and uptake rates were much lower than 8% determined under the conditions of drastically (about 10 K per 30 min) increased or decreased ambient air temperatures. The experimental set-up proved to be a most valuable tool to determine and analyse interactions between transpiration and water uptake, changes in plant water status and the buffering of negative Jwnet). Increasing the temperature of ambient air resulted, for both species investigated, in a quick and considerably enhanced transpiration, but there was only a minor impact on water uptake. Water loss exceeding uptake was buffered by internal water reserves which were refilled within about 1 d after the plant was relieved of heat and drought stress caused by a period of high ambient air temperatures and high water vapour saturation deficits of the air. Repeated simulation of such stress periods showed that the absolute values of transpiration and the water uptake for 24 h can vary, but the diurnal course of the values showed the same pattern if the environmental conditions were identical. Such standardized diurnal transpiration and water uptake curves could be very useful for the validation of mathematical models used to describe plant water relation
Leaf Temperatures in a Gas Exchange Chamber and in the Open Air
Leaf temperatures in a Koch fully climatized gas-exchange chamber as designed by Siemens and in a similarly equipped open-air reference were measured with horizontally and vertically inserted thermocouples on Nerium oleander L. On a sunny day with only little air movement and an average air temperature of 20.4 °C, leaf over-temperatures in the gas-exchange chamber were lower on average by 2.2 K. The extent of reduction of over-temperature in the chamber is determined by the reduced global radiation in the chamber and the differences of wind velocities in chamber and reference. Differences in the ventilation intensity in the chamber have no demonstrable influence on the leaf over-temperatures. The over-temperatures of the reference leaves, on the other hand, depend to a large degree on air velocity. The changed radiation and air flow conditions in the chamber as compared with open-air conditions have consequences for the physiological reactions of the enclosed plant and must be taken into account when comparing results from gas-exchange measurements with open-air conditions. For further improvements of gas-exchange measurement equipment, air flow conditions and radiation quantity and quality might be starting point
Six-body Light-Front Tamm-Dancoff approximation and wave functions for the massive Schwinger model
The spectrum of the massive Schwinger model in the strong coupling region is
obtained by using the light-front Tamm-Dancoff (LFTD) approximation up to
including six-body states. We numerically confirm that the two-meson bound
state has a negligibly small six-body component. Emphasis is on the usefulness
of the information about states (wave functions). It is used for identifying
the three-meson bound state among the states below the three-meson threshold.
We also show that the two-meson bound state is well described by the wave
function of the relative motion.Comment: 19 pages, RevTeX, 7 figures are available upon request; Minor errors
have been corrected; Final version to appear in Phys.Rev.
Glycosylation efficiencies on different solid supports using a hydrogenolysis-labile linker
Hardness-based plasticity and fracture model for quench-hardenable boron steel (22MnB5)
A comprehensive strain hardening and fracture characterization of different grades of boron steel blanks has been performed, providing the foundation for the implementation into the modular material model (MMM) framework developed by Volkswagen Group Research for an explicit crash code. Due to the introduction of hardness-based interpolation rules for the characterized main grades, the hardening and fracture behavior is solely described by the underlying Vickers hardness. In other words, knowledge of the hardness distribution within a hot-formed component is enough to set up the newly developed computational model. The hardness distribution can be easily introduced via an experimentally measured hardness curve or via hardness mapping from a corresponding hot-forming simulation. For industrial application using rather coarse and computationally inexpensive shell element meshes, the user material model has been extended by a necking/post-necking model with reduced mesh-dependency as an additional failure mode. The present paper mainly addresses the necking/post-necking model
ERTS-1 applications to Minnesota land use mapping
Land use class definitions that can be operationally employed with ERTS-1 imagery are being developed with the cooperation of personnel from several state, regional, and federal agencies with land management responsibilities within the state and the University of Minnesota. Investigations of urban, extractive, forest, and wetlands areas indicate that it is feasible to subdivide each of these classes into several sub-classes with the use of ERTS-1 images from one or more time periods
- …