Correlation between magnetic interactions and domain structure in A1 FePt ferromagnetic thin films

We have investigated the relationship between the domain structure and the magnetic interactions in a series of FePt ferromagnetic thin films of varying thickness. As-made films grow in the magnetically soft and chemically disordered A1 phase that may have two distinct domain structures. Above a critical thickness $d_{cr}\sim 30$ nm the presence of an out of plane anisotropy induces the formation of stripes, while for $d<d_{cr}$ planar domains occur. Magnetic interactions have been characterized using the well known DCD-IRM remanence protocols, $\delta M$ plots, and magnetic viscosity measurements. We have observed a strong correlation between the domain configuration and the sign of the magnetic interactions. Planar domains are associated with positive exchange-like interactions, while stripe domains have a strong negative dipolar-like contribution. In this last case we have found a close correlation between the interaction parameter and the surface dipolar energy of the stripe domain structure. Using time dependent magnetic viscosity measurements, we have also estimated an average activation volume for magnetic reversal, $\langle V_{ac}\rangle \sim 1.37\times 10^{4}$ nm$^{3},$ which is approximately independent of the film thickness or the stripe period.Comment: 25 pages, 11 figure

Microstructure and mechanical behavior of porous Ti-6Al-4V parts obtained by selective laser melting

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Rapid prototyping allows titanium porous parts with mechanical properties close to that of bone tissue to be obtained. In this article, porous parts of the Ti-6Al-4V alloy with three levels of porosity were obtained by selective laser melting with two different energy inputs. Thermal treatments were performed to determine the influence of the microstructure on the mechanical properties. The porous parts were characterized by both optical and scanning electron microscopy. The effective modulus, yield and ultimate compressive strength were determined by compressive tests. The martensitic alpha' microstructure was observed in all of the as-processed parts. The struts resulting from the processing conditions investigated were thinner than those defined by CAD models, and consequently, larger pores and a higher experimental porosity were achieved. The use of the high-energy input parameters produced parts with higher oxygen and nitrogen content, their struts that were even thinner and contained a homogeneous porosity distribution. Greater mechanical properties for a given relative density were obtained using the high-energy input parameters. The as-quenched martensitic parts showed yield and ultimate compressive strengths similar to the as-processed parts, and these were greater than those observed for the fully annealed samples that had the lamellar microstructure of the equilibrium alpha+beta phases. The effective modulus was not significantly influenced by the thermal treatments. A comparison between these results and those of porous parts with similar geometry obtained by selective electron beam melting shows that the use of a laser allows parts with higher mechanical properties for a given relative density to be obtained. (C) 2013 Elsevier Ltd. All rights reserved.2698108Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES

Ductility Improvement Due To Martensite Alpha ' Decomposition In Porous Ti-6al-4v Parts Produced By Selective Laser Melting For Orthopedic Implants

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Ti-6Al-4V parts obtained by selective laser melting typically have an acicular alpha' martensitic microstructure whose ductility is low. Thus, post-heat treatments are useful for increasing ductility. In this work, the effects of sub-beta-transus heat treatments on the mechanical properties of Ti-6Al-4V parts with porous structures are correlated with martensite alpha' phase decomposition. The precipitation of beta phase and the gradual transformation of alpha' into alpha phase by the diffusion of excess vanadium from alpha' to beta phase are proposed to be the main events of martensite alpha' phase decomposition in parts fabricated by selective laser melting. The heat treatment performed at 650 degrees C for 1 h produced no microstructural changes, but the samples treated for at the same temperature 2 h showed alpha fine precipitation of beta phase along the alpha' needle boundaries. The heat treatment performed at 800 degrees C for 1 or 2 h produced alpha fine alpha+beta microstructure, in which beta phase are present as particles fewer in number and larger in size, when compared with the ones present in the sample heat-treated at 650 degrees C for 2 h. Heat-treatment of the parts at 800 degrees C for 2 h proved to be the best condition, which improved the ductility of the samples while only slightly reducing their strength. (C) 2015 Elsevier Ltd. All rights reserved.54149158Sao Paulo State Research Foundation (FAPESP, Brazil) [2011/19982-2]National Council for Scientific and Technological Development (CNPq, Brazil) [483733/2010-5]Brazilian Federal Agency for Support and Improvement of Higher Education (CAPES, Brazil)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES

Ductility Improvement Due To Martensite α' Decomposition In Porous Ti-6al-4v Parts Produced By Selective Laser Melting For Orthopedic Implants.

Ti-6Al-4V parts obtained by selective laser melting typically have an acicular α' martensitic microstructure whose ductility is low. Thus, post-heat treatments are useful for increasing ductility. In this work, the effects of sub-β-transus heat treatments on the mechanical properties of Ti-6Al-4V parts with porous structures are correlated with martensite α' phase decomposition. The precipitation of β phase and the gradual transformation of α' into α phase by the diffusion of excess vanadium from α' to β phase are proposed to be the main events of martensite α' phase decomposition in parts fabricated by selective laser melting. The heat treatment performed at 650°C for 1h produced no microstructural changes, but the samples treated for at the same temperature 2h showed a fine precipitation of β phase along the α' needle boundaries. The heat treatment performed at 800°C for 1 or 2h produced a fine α+β microstructure, in which β phase are present as particles fewer in number and larger in size, when compared with the ones present in the sample heat-treated at 650°C for 2h. Heat-treatment of the parts at 800°C for 2h proved to be the best condition, which improved the ductility of the samples while only slightly reducing their strength.54149-15