17 research outputs found
Casemix, management, and mortality of patients receiving emergency neurosurgery for traumatic brain injury in the Global Neurotrauma Outcomes Study: a prospective observational cohort study
Detecting sub-voxel microvasculature with USPIO-enhanced susceptibility-weighted MRI at 7 T
BACKGROUND: Susceptibility weighted imaging (SWI) combines phase with magnitude information to better image sub-voxel veins. Recently, it has been extended to image very small sub-voxel arteries and veins by injecting intravenously the ultra-small superparamagnetic iron oxide, Ferumoxytol.
OBJECTIVE: To determine practical experimental imaging parameters for sub-voxel cerebral vessels at 7 T.
METHODS: Six Wistar-Kyoto rats aged 7-13 weeks were imaged. For a given spatial resolution, SWI was acquired pre- and post- Ferumoxytol with doses of 2, 4, 6 and 8 mg/kg and echo times (TEs) of 5, 10 and 15 ms at each dose. The spatial resolutions of 62.5 x 125 x 250 mum(3) (acquisition time of 7.5 min) and 62.5 x 62.5 x 125 mum(3) (30 min) were used. Both SWI and quantitative susceptibility mapping (QSM) data were analyzed. Contrast-to-noise ratio (CNR) was measured and used to determine the optimal practical imaging parameters for detection of small cortical penetrating arteries.
RESULTS: For a given spatial resolution with an aspect ratio (frequency: phase: slice) of 2:4:8 relative to the vessel size, we found the TE-dose index (TE x dose) must be at least 40 ms·mg/kg for both SWI and QSM to reveal the most vessels. The higher the TE-dose index, the better the image quality for both SWI and QSM up to 60 ms·mg/kg.
CONCLUSIONS: There is an optimal TE-dose index for improved visualization of sub-voxel vessels. Choosing the smallest TE and the largest allowed dose made it possible to run the sequence efficiently. In practice, the aspect ratio of 2:4:8 and the TE-dose index ranging from 40 to 60 ms·mg/kg provided the optimal and most practical solution
Recommended from our members
Cyclic production of biocompatible few-layer graphene ink with in-line shear-mixing for inkjet-printed electrodes and Li-ion energy storage
AbstractThe scalable production of two-dimensional (2D) materials is needed to accelerate their adoption to industry. In this work, we present a low-cost in-line and enclosed process of exfoliation based on high-shear mixing to create aqueous dispersions of few-layer graphene, on a large scale with a Yw ~ 100% yield by weight and throughput of ϕ ~ 8.3 g h−1. The in-line process minimises basal plane defects compared to traditional beaker-based shear mixing which we attribute to a reduced Reynolds number, Re ~ 105. We demonstrate highly conductive graphene material with conductivities as high as σ ∼ 1.5 × 104 S m−1 leading to sheet-resistances as low as Rs ∼ 2.6 Ω □−1 (t ∼ 25 μm). The process is ideal for formulating non-toxic, biocompatible and highly concentrated (c ∼ 100 mg ml−1) inks. We utilise the graphene inks for inkjet printable conductive interconnects and lithium-ion battery anode composites that demonstrate a low-rate lithium storage capability of 370 mAh g−1, close to the theoretical capacity of graphite. Finally, we demonstrate the biocompatibility of the graphene inks with human colon cells and human umbilical vein endothelial cells at high c ∼ 1 mg ml−1 facilitating a route for the use of the graphene inks in applications that require biocompatibility at high c such as electronic textiles.</jats:p