The influence of clearance on friction, lubrication and squeaking in large diameter metal-on-metal hip replacements

Large diameter metal-on-metal bearings (MOM) are becoming increasingly popular, addressing the needs of young and more active patients. Clinical data has shown excellent short-to-mid-term results, though incidences of transient squeaking have been noted between implantation and up to 2 years post-operative. Geometric design features, such as clearance, have been significant in influencing the performance of the bearings. Sets of MOM bearings with different clearances were investigated in this study using a hip friction simulator to examine the influence of clearance on friction, lubrication and squeaking. The friction factor was found to be highest in the largest clearance bearings under all test conditions. The incidence of squeaking was also highest in the large clearance bearings, with all bearings in this group squeaking throughout the study. A very low incidence of squeaking was observed in the other two clearance groups. The measured lubricating film was found to be lowest in the large clearance bearings. This study suggests that increasing the bearing clearance results in reduced lubricant film thickness, increased friction and an increased incidence of squeaking

Model and experiments to determine lubricant film formation and frictional torque in aircraft landing gear pin joints

Pin joints are found in many large articulating structures. They tend to be under high load and articulate slowly; so, the joints typically operate in the boundary or mixed lubrication regimes. This means that the operating torque depends on the respective proportions of liquid and solid contact between the joint mating faces. In this article, a mixed lubrication model of a grease-lubricated landing gear joint is established to determine a theoretical Stribeck curve, frictional torque and lubricant film thickness under different loads. Parameters describing pin joint working conditions, geometry, lubricant properties and pin/bush texture are used. The model can also predict the proportion of the load that is supported by contacting asperities and lubricant film. The changing proportions of these two parts indicate transformations between different lubrication regimes. Experiments on an instrumented pin joint have been carried out to compare with the predicted friction and torque performance. Theoretical calculation results show good consistency with experimental plots at high load. But under low load, the real friction between pin and bush is significantly lower than theoretical predictions

Transient Tribo-Dynamics of Thermo-Elastic Compliant High-Performance Piston Skirts

Advanced piston technology for motorsport applications is driven through development of lightweight pistons with preferentially compliant short partial skirts. The preferential compliance is achieved through structural stiffening, such that a greater entrainment wedge is achieved at the skirt’s bottom edge through thermo-elastic deformation, whilst better conforming contact geometry at the top of the skirt. In practice, the combination of some of these conditions is intended to improve the load-carrying capacity and reduce friction. The approach is fundamental to the underlying ethos of race and high-performance engine technology. Contact loads of the order of 5 kN and contact kinematics in the range 0–35 m/s result in harsh transient tribological conditions. Therefore, piston design requires detailed transient analysis, which integrates piston dynamics, thermo-elastic distortion and transient elastohydrodynamics. The paper provides such a detailed analysis as well as verification of the same using non-invasive ultrasonic-assisted lubricant film thickness measurement from a fired engine under normal operating conditions, an approach not hitherto reported in literature. Good agreement is noted between measured film thickness and predictions

Effect of different rubber materials on husking dynamics of paddy rice

The conventional way to husk rice is to pass it between two rubber rollers that are rotating with a surface speed differential. The resulting normal pressure and shear stress causes the husk to be peeled away from the kernel. The process is suited to high-rice flow rates, but is energy intensive and can result in considerable wear to the surfaces of the rollers. The operating parameters for machines of this design are usually determined and set empirically. In this article, some experiments and calculations had been carried out in order to explore the mechanisms involved in husking rice grains using this method. A simple sliding friction rig with load cell and high-speed camera was used to observe the mechanisms that occur during husking. The husking performance of different rubbers was compared for changes in the applied normal load. It was found that grains rotate between the rubber counterfaces on initial motion before being husked. In addition, harder rubbers were found to husk a higher proportion of entrained grains at lower applied normal load. By measuring the coefficient of friction between rice and rubber samples, the shear force required to husk a given percentage of grains could be calculated and was shown to be constant regardless of rubber type. Based on the mechanism seen in the high-speed video, it was evident that there was a limiting shear stress that was the governing factor over the husked ratio

Effect of different rubber materials on husking dynamics of paddy rice

The conventional way to husk rice is to pass it between two rubber rollers that are rotating with a surface speed differential. The resulting normal pressure and shear stress causes the husk to be peeled away from the kernel. The process is suited to high-rice flow rates, but is energy intensive and can result in considerable wear to the surfaces of the rollers. The operating parameters for machines of this design are usually determined and set empirically. In this article, some experiments and calculations had been carried out in order to explore the mechanisms involved in husking rice grains using this method. A simple sliding friction rig with load cell and high-speed camera was used to observe the mechanisms that occur during husking. The husking performance of different rubbers was compared for changes in the applied normal load. It was found that grains rotate between the rubber counterfaces on initial motion before being husked. In addition, harder rubbers were found to husk a higher proportion of entrained grains at lower applied normal load. By measuring the coefficient of friction between rice and rubber samples, the shear force required to husk a given percentage of grains could be calculated and was shown to be constant regardless of rubber type. Based on the mechanism seen in the high-speed video, it was evident that there was a limiting shear stress that was the governing factor over the husked ratio

A Concerted HIF-1α/MT1-MMP Signalling Axis Regulates the Expression of the 3BP2 Adaptor Protein in Hypoxic Mesenchymal Stromal Cells

Increased plasticity, migratory and immunosuppressive abilities characterize mesenchymal stromal cells (MSC) which enable them to be active participants in the development of hypoxic solid tumours. Our understanding of the oncogenic adaptation of MSC to hypoxia however lacks the identification and characterization of specific biomarkers. In this study, we assessed the hypoxic regulation of 3BP2/SH3BP2 (Abl SH3-binding protein 2), an immune response adaptor/scaffold protein which regulates leukocyte differentiation and motility. Gene silencing of 3BP2 abrogated MSC migration in response to hypoxic cues and generation of MSC stably expressing the transcription factor hypoxia inducible factor 1alpha (HIF-1α) resulted in increased endogenous 3BP2 expression as well as cell migration. Analysis of the 3BP2 promoter sequence revealed only one potential HIF-1α binding site within the human but none in the murine sequence. An alternate early signalling cascade that regulated 3BP2 expression was found to involve membrane type-1 matrix metalloproteinase (MT1-MMP) transcriptional regulation which gene silencing abrogated 3BP2 expression in response to hypoxia. Collectively, we provide evidence for a concerted HIF-1α/MT1-MMP signalling axis that explains the induction of adaptor protein 3BP2 and which may link protein binding partners together and stimulate oncogenic MSC migration. These mechanistic observations support the potential for malignant transformation of MSC within hypoxic tumour stroma and may contribute to evasion of the immune system by a tumour