To sail the new ocean of space

Space effort by united state

The Exploration of Space

No abstract availabl

Aerodynamic characteristics of circular-arc airfoils at high speeds

The aerodynamic characteristics of eight circular-arc airfoils at speeds of 0.5, 0.8, 0.95, and 1.08 times the speed of sound have been determined in an open-jet air stream 2 inches in diameter, using models of 1-inch chord. The lower surface of each airfoil was plane; the upper surface was cylindrical. As compared with the measurements described in NACA-TR-319, the circular-arc airfoils at speeds of 0.95 and 1.08 times the speed of sound are more efficient than airfoils of the R. A. F. or Clark Y families. At a speed of 0.5 times the speed of sound, the thick circular-arc sections are extremely inefficient, but thin sections compare favorably with those of the R. A. F. family. A moderate round of the sharp edges changes the characteristics very little and is in many instances beneficial. The results indicate that the section of the blades of propellers intended for use at high tip-speeds should be of the circular-arc form for the outer part of the blade and should be changed gradually to the R. A. F. or Clark Y form as the hub is approached

Aerodynamic Characteristics of Twenty-Four Airfoils at High Speeds

The aerodynamic characteristics of 24 airfoils are given for speeds of 0.5, 0.65, 0.8, 0.95, and 1.08 times the speed of sound, as measured in an open-jet air stream 2 inches in diameter, using models of 1-inch chord. The 24 airfoils belong to four general groups. The first is the standard R. A. F. family in general use by the Army and Navy for propeller design, the members of the family differing only in thickness. This family is represented by nine members ranging in thickness from 0.04 to 0.20 inch. The second group consists of five members of the Clark Y family, the members of the family again differing only in thickness. The third group, comprising six members, is a second R. A. F. Family in which the position of the maximum ordinate is varied. Combined with two members of the first R.A.F. family, this group represents a variation of maximum ordinate position from 30 to 60 percent of the chord in two camber ratios, 0.08 and 0.16. The fourth group consists of three geometrical forms, a flat plate, a wedge, and a segment of a right circular cylinder. In addition one section used in the reed metal propeller was included. These measurements form a part of a general program outlined at a Conference on Propeller Research organized by the National Advisory Committee for Aeronautics and the work was carried out with the financial assistance of the committee (author

Investigation of Turbulence in Wind Tunnels by a Study of the Flow About Cylinders

With the assistance and cooperation of the National Advisory Committee for Aeronautics the Bureau of Standards has been engaged for the past year in an investigation of turbulence in wind tunnels, especially in so far as turbulence affects the results of measurements in different wind tunnels. Two methods of making such studies are described in this report together with the results of the use in the 54-inch wind tunnel of the Bureau of Standards. The first method consists in measuring the drag of circular cylinders; the second in measuring the static pressure at some fixed point. Both methods show that the flow is not entirely free from irregularities

Pressure Distribution Over Airfoils at High Speeds

This report deals with the pressure distribution over airfoils at high speeds, and describes an extension of an investigation of the aerodynamic characteristics of certain airfoils which was presented in NACA Technical Report no. 207. The results presented in report no. 207 have been confirmed and extended to higher speeds through a more extensive and systematic series of tests. Observations were also made of the air flow near the surface of the airfoils, and the large changes in lift coefficients were shown to be associated with a sudden breaking away of the flow from the upper surface. The tests were made on models of 1-inch chord and comparison with the earlier measurements on models of 3-inch chord shows that the sudden change in the lift coefficient is due to compressibility and not to a change in the Reynolds number. The Reynolds number still has a large effect, however, on the drag coefficient. The pressure distribution observations furnish the propeller designer with data on the load distribution at high speeds, and also give a better picture of the air-flow changes

Effect of Turbulence in Wind-Tunnel Measurements

This paper gives some quantitative measurements of wind tunnel turbulence and its effect on the air resistance of spheres and airship models, measurements made possible by the hot wire anemometer and associated apparatus in its original form was described in Technical Report no. 320 and some modifications are presented in an appendix to the present paper. One important result of the investigation is a curve by means of which measurements of the air resistance of spheres can be interpreted to give the turbulence quantitatively. Another is the definite proof that the discrepancies in the results on the N. P. L. Standard airship models are due mainly to differences in the turbulences of the wind tunnels in which the tests were made. An attempt is made to interpret the observed results in terms of the boundary layer theory and for this purpose a brief account is given of the physical bases of this theory and of conceptions that have been obtained by analogy with the laws of flow in pipes

The Design of Low-Turbulence Wind Tunnels

Within the past 10 years there have been placed in operation in the United States four low-turbulence wind tunnels of moderate cross-sectional area and speed, one at the National Bureau of Standards, two at the NACA Langley Laboratory, and one at the NACA Ames Laboratory. This paper reviews briefly the state of knowledge and those features which make possible the attainment of low turbulence in wind tunnels. Specific applications to two wind tunnels are described

The effect of area aspect ratio on the yawing moments of rudders at large angles of pitch on three fuselages

This reports presents the results of measurements made of yawing moments produced by rudder displacement for seven rudders mounted on each of three fuselages at angles of pitch of 0 degree, 8 degrees, 12 degrees, 20 degrees, 30 degrees and 40 degrees. The dimensions of the rudders were selected to cover the range of areas and aspect ratios commonly used, while the ratios of rudder area to fin area and of rudder chord to fin chord were kept approximately constant. An important result of the measurements is to show that increased aspect ratio gives increased yawing moments for a given area, provided the maximum rudder displacement does not exceed 25 degrees. If large rudder displacements are used, the effect of aspect ratio is not so great

The Measurement of Fluctuations of Air Speed by the Hot-Wire Anemometer

The hot-wire anemometer suggests itself as a promising method for measuring the fluctuating air velocities found in turbulent flow. The only obstacle is the presence of a lag due to the limited energy input which makes even a fairly small wire incapable of following rapid fluctuations with accuracy. This paper gives the theory of the lag and describes an experimental arrangement for compensating for the lag for frequencies up to 100 or more per second when the amplitude of the fluctuation is not too great. An experimental test of the accuracy of compensation and some results obtained with the apparatus in a wind-tunnel air stream are described. While the apparatus is very bulky in its present form, it is believed possible to develop a more portable arrangement. (author