REMOVED: Mastering Membranes to Command Functions

n/

REMOVED: Modeling the Performance of Flat and Capillary Membrane Modules in Vacuum Membrane Distillation

n/

Controlled Release of Tramadol from Mixed Matrix Membranes

In this work mixed matrix membranes (zeolite loaded) were prepared and tested as potential devices for the controlled release of tramadol hydrochloride. Due to the hydrophilic nature of the drug, a hydrophobic polymer (polydimethylsiloxane) was chosen for the membrane preparation. NaX zeolites was added to PDMS matrix as modulating agent with the aim to obtain a linear and adequate delivery of the drug in the time as required by the therapeutic needs of this opioid. About the different investigated systems, the PDMS membrane containing 17 wt% of zeolite and 0.2 wt% of drug seems to be the most promising for application as transdermal device. Different mathematical models (Zero order, First order, Higuchi, Bhaskar, and Korsemeyer-Peppas) were used to interpret the drug release mechanism from the different Mixed matrix membranes. The experimental data showed good fit with three different models: Higuchi, Bhaskar and Korsemeyer-Peppas

Evaluation the potential and energy efficiency of dual stage pressure retarded osmosis process

© 2017 Power generation by means of Pressure Retarded Osmosis (PRO) has been proposed for harvesting the energy of a salinity gradient. Energy recovery by the PRO process decreases along the membrane module due to depleting of the chemical potential across the membrane and concentration polarization effects. A dual stage PRO (DSPRO) design can be used to rejuvenate the chemical potential difference and reduce the concentration polarization on feed solution. Several design configurations were suggested for the membrane module arrangements in the first and second stage of the PRO process. PRO performance was evaluated for a number of salinity gradients proposed by coupling Dead Sea water or Reverse Osmosis (RO) brine with seawater or wastewater effluent. Maximum specific energy of inlet and outlet feeds was calculated using a developed computer model to identify the amount of recovered and remaining energy. Initially, specific power generation by the PRO process increased by increasing the number of modules of the first stage. Maximum specific energy is calculated along the PRO module to understand the degradation of the maximum specific energy in each module before introducing a second stage PRO process. Adding a second stage PRO process resulted in a sharp increase of the chemical potential difference and the specific energy yield of the process. Between 10% and 13% increase of the specific power generation was achieved by the DSPRO process for the Dead Sea-seawater salinity gradient depending on the dual stage design configuration. For Dead Sea-RO brine, 12–16% increase of the specific power generation was achieved by the dual stage PRO process. For Dead Sea-wastewater and RO brine-wastewater, a neutral and sometimes negative impact occurred when a second stage PRO process was introduced. We concluded that, for a given draw solution concentration, dual stage performs better than the conventional PRO process at high feed salinities, yet requires lower hydraulic pressure

REMOVED: Combination of Pre-Treatments, Membrane Bioreactor and Forward Osmosis for a Less Fouled Valorisation of Olive Mill Wastewater

n/

Polyimide hollow fiber membranes for CO2 separation from wet gas mixtures

Matrimid®5218 hollow fiber membranes were prepared using the dry-wet spinning process. The transport properties were measured with pure gases (H2, CO2, N2, CH4 and O2) and with a mixture (30% CO2 and 70% N2) in dry and wet conditions at 25 ºC, 50 ºC, 60 ºC and 75 ºC and up to 600 kPa. Interesting values of single gas selectivity up to 60 ºC (between 31 and 28 for CO2/N2 and between 33 and 30 for CO2/CH4) in dry condition were obtained. The separation factor measured for the mixture was 20% lower compared to the single gas selectivity, in the whole temperature range analyzed. In saturation conditions the data showed that water influences the performance of the membranes, inducing a reduction of the permeance of all gases. Moreover, the presence of water caused a decrease of single gas selectivity and separation factor, although not so significant, highlighting the very high water resistance of hollow fiber membrane modules

An alternative encapsulation approach for production of active chitosan-propolis beads

Encapsulation is a promising technology to carry natural active substances, preventing their loss and maintaining their stability until use. Beads of chitosan-containing propolis have been prepared using a mono-pore filter device, which permits the encapsulation of natural polyphenols avoiding heat treatments, high shear rates and the use of toxic solvents. Beads proved to be active against Bacillis cereus, Escherichia coli, Listeria innocua, Pseudomonas fluorescens, Yarrovia lipolytica and three moulds strains; the highest effect was found against Staphylococcus aureus (MIC 0.8 mg beads mL-1). Results in liquid cultures of S. aureus evidenced that beads were able to release the flavonoids from propolis: the diffusion of the active compounds is a key factor in the exploitation of the microbial activity. The obtained chitosan-propolis beads represent an example of natural antimicrobial delivery system that could be used to prevent the growth of pathogenic/spoilage bacteria in food applications

Toward the Next Generation of Sustainable Membranes from Green Chemistry Principles

Large-scale membrane technology has been widely implemented and rapidly growing for roughly 40 years. However, considering its entire life cycle, there are aspects being characterized by low sustainability, and this industry certainly cannot be defined as green. In the membrane manufacturing process, raw materials mainly rely on nonbiodegradable petroleum-based polymers and hazardous solvents. These materials are thus associated with the energy crisis and with disposal burdens at the end of their lifetime, and they pose risks to workers and the environment. Therefore, biobased polymers and green solvents should be employed within the membrane preparation process and replace traditional ones. Moreover, the wastewater generated from membrane fabrication processes contains an important amount of organic solvents and should be efficiently treated or recycled before discharge. The application of artificial intelligence in membrane manufacturing and use processes can also improve efficiency significantly. Finally, a large number of spent membrane elements should also be reused and recovered, rather than landfilled. This review critically evaluates the recent advances in methods to improve the sustainability of membrane technology, specifically emphasizing the progresses made, with regard to the above aspects. This review thus analyzes the needs for membrane industry transformations in the light of circular economy