5 research outputs found

    The microstructure and properties of as-cast Sn-Zn-Bi solder alloys

    No full text
    U radu su prikazani rezultati ispitivanja strukturnih i mehaničkih karakteristika bezolovnih lemnih legura u sistemu kalaj-cink-bizmut. Nakon dobijanja legura u indukcionoj peći sa zaštitnom atmosferom, trostrukim pretapanjem odmerene količine čistih metala, izvršena su ispitivanja strukture tako dobijenih uzoraka legura optičkom i skenirajućom electronskom mikroskopijom (SEM). Energetskom disperzivnom spektroskopijom (EDS) određen je hemijski sastav faza prisutnih u strukturi legura. Izvršena su merenja tvrdoće, i zatezne čvrstoće ispitivanih legura. Sva istraživanja su sprovedena sa ciljem boljeg upoznavanja osobina legura u sistemu Sn-Zn-Bi, koji se smatra odgovarajućom zamenom olovnih lemnih legura.Research on the lead-free solders has attracted wide attention, mostly as the result of the implementation of the Directive on the Restriction of the Use of Hazardous Substances in Electrical and Electronic Equipment. The Sn-Zn solder alloys have been considered to be one of the most attractive lead-free solders due to its ability to easily replace Sn-Pb eutectic alloy without increasing the soldering temperature. Furthermore, the mechanical properties are comparable or even superior to those of Sn-Pb solder. However, other problems still persist. The solution to overcoming these drawbacks is to add a small amount of alloying elements (Bi, Ag, Cr, Cu and Sb) to the Sn-Zn alloys. Microstructure, tensile strength, and hardness of the selected Sn-Zn-Bi ternary alloys have been investigated in this study. The SEM-EDS was used for the identification of co-existing phases in the samples. The specimens' microstructures are composed of three phases: Sn-rich solid solution as the matrix, Bi-phase and Zn-rich phase. The Bi precipitates are formed around the Sn-dendrit grains as well as around the Zn-rich phase. The amount of Bi segregation increases with the increase of Bi content. The Sn-Zn-Bi alloys exhibit the high tensile strength and hardness, but the values of these mechanical properties decrease with the increase of Bi content, as well as the reduction of Zn content. The results presented in this paper may offer further knowledge of the effects various parameters have on the properties of lead-free Sn-Zn-Bi solders

    TOTAL HIP ARTHROPLASTY IN PATIENTS SUFFERING FROM RHEUMATOID ARTHRITIS – A REPORT ON TWO CASES

    No full text
    Rheumatoid arthritis is traditionally considered a chronic, inflammatory autoimmune disorder of unknown etiology.It is a disabling and painful inflammatory condition, which can lead to substantial loss of mobility due to pain and joint destruction. Clinical characteristics of the rheumatoid hip are pain, limited range of motion, and rapid onset of cartilage destruction resulting in secondary changes in other lower limb joints and the spine. Radiography showed intensive osteoporosis and later protrusion of acetabulum. Treatment of rheumatoid coxitis is specific, which depends on the stage of disease, subjective and objective complications, and can be medicamentous, functional and operative.The study presents the treatment of two patients with rheumatoid arthritis with total hip arthroplasty at the Clinic of Orthopaedics and Traumatology Clinical Center Nis. In a fifty-five-old patient with the diagnosis of rheumatoid arthritis, the rheumatoid hip joint underwent a cementless total hip arthroplasty. In a sixty-eight-year old patient, the rheumatoid hip joint underwent total hip arthroplasty with cement. In both patients we obtained good functional results.Total hip arthroplasty in patients with rheumatoid coxitis relieves pain and prevents invalidity conditioned by destruction of the hip joint
    corecore