The effect of weak inertia on the emptying of a tube (vol 14, pg 2102, 2002): Erratum

International audienceno abstrac

Dust emission in powder handling: Free falling particle plume characterisation

Dust generation during solids handling, principally from the free falling of bulk materials and their impact on stockpiles, can be a health threat for operators and a cause of dust explosions. The proper design of a dust emission control system requires knowledge of the behaviour of the free falling jet, in particular the amount of air entrained by the falling powder and the concentration of dust liberated. The focus in this present paper is on the effect of drop height of a free falling jet on segregation by particle size, particle velocity, changes in particle concentration and entrained air in the dust plume. This gives a quantification of the important parameters and the concentration of dust emitted during a free fall

Granular flows down inclined channels with a strain-rate dependent friction coefficient. Part I: Non-cohesive materials

The flow of a granular material down an incline of finite width with a strain-rate dependent coefficient of friction and a conical yield criterion is semi-analytically obtained using a characteristic method for flows on a deep layer of grains. This analysis leads to a flow field with three distinct zones: a Bagnold-flow zone below the free surface, a dead zone and a matching zone between the two, linked to slippage at the wall. A good agreement between the computed flow field and experimental data is obtained

Slip events and dilatancy in a sheared fine noncohesive powder

International audienceWe present experimental results of the transition from steady-state sliding to oscillatory motion for a fine noncohesive powder, sheared in an annular cell. The onset of instability is compared to the Dieterich-Ruina model for solid friction. We present data showing that at low velocity and close to the transition, the major sliding jumps are preceded by a short or long period of unstable plastic yielding of the granular matter. This ambivalent behavior suggests that the jumps are initiated when the sliding overcomes a critical velocity. During the stick-slip motion, the dilatancy of the powder bed has been also observed: the slippage is associated with a compaction whose value increases with the jump in the friction coefficient

Fluid coating from a polymer solution

International audienceNew experiments on coating of a wire with aqueous poly(ethylene oxide) solutions are reported. If these experiments are compared with coating with a pure Liquid of the same physical characteristics, a strong thickening of the liquid layer is observed. This effect is described by considering the normal stresses, which allows us to obtain an analytical expression for the coated thickness in good agreement with the data

Applied surveying education : documenting cultural heritage in 3D in the city of Ghent (Belgium) using laser scanning and photo modelling

For several years the city of Ghent (Belgium) and the Ghent University, Department of Geography have been working together to document and measure important cultural heritage sites in 3D. The partnership enables master students in Geomatics and Surveying at the Ghent University to take part in a project driven measuring campaign. During the project, students use and compare several 3D data acquisition methods. This allows the students to implement their theoretical knowledge in the field. The used methods are analysed and critically compared by the students. Through this hands-on-training, students are encouraged to think “outside the box”. When problems occur, they are stimulated to think how these problems could have happened and most importantly how they can solve them. The documentation of these historic monuments in Ghent will be used during future renovation works and archaeological research. This paper will discuss the measurements in the Ghent City Museum (Stadsmuseum or STAM). The following methods are applied during the extensive field work: engineering surveying using total station and GNSS, photo modelling and laser scanning. The deliverables are created in a CAD or GIS environment. After successful completion of the course, students have gained a significant expertise concerning the processing of topographic data, 3D point clouds and imagery in an integrated way. This knowledge can be used after their studies to assess which equipment is most suitable for any given survey project. The final products of the photo modelling and the laser scanning process is a 3D model. Furthermore, digital elevation models and orthorectified images of the historic monument can be created. The orthorectified images are visualised and processed into high resolution orthophoto plans, in a CAD or GIS environment

Dust emission by powder handling: Influence of the hopper outlet on the dust plume

Dust generation in solids handling involving free fall of bulk materials and impacts on a stockpile can cause many problems in industry and be a great danger for operators health. This paper describes an experimental set up to characterize the dust plume formed in free fall of powders from a hopper and investigates the influence of various outlet geometries on the dust plume. For this purpose an image analysis technique was developed to quantify the characteristics of the dust plume

Mechanical Resistance due to Shearing of Partially Wet Granular Media

International audienceMixing granular media with a given amount of liquid is an operation conducted and used intensively for the preparation of concrete. The power and time required to obtain good homogeneity of the granular paste are known to have a complex relationship with the physical properties of the particles, with the liquid and with the mixer design. In this paper some of these issues are addressed by evaluating the shear resistance of a granular paste. Using model spherical materials (glass beads) and ground and sieved minerals (calcite CaCO3), we investigate experimentally the impact of the particle size, liquid amount and morphology of the particles. From quasi-static experiments in shear cells, different regimes of shear resistance are revealed. In dry conditions, van der Waals' forces dominate. In wet conditions, a capillary or consolidation regime where shear resistance is dominated by capillary forces is strongly impacted by the morphology of the particles and by the formation of texture. These regimes are qualitatively observed in a bowl mixer for which the variation of the current intensity correlates with the shear resistance observed in quasi-static experiments

Dust emission by powder handling: Comparison between numerical analysis and experimental results

The dust generation occurring during the handling of bulk materials in free falls or at the impact on a stockpile can be a source of danger for the operators health. Proper design of control systems of fugitive dust requires knowledge of the behavior of the free falling powder, the air it entrains, and the concentration of dust liberated. This paper presents first a simple model for a free falling column of bulk solids and compares it with relevant previous research. This two phase model predicts the particle and air velocities, and especially the volumetric flow of induced air in the column without dependence on any empirical constant like the entrainment constant used in the plume model. For small drop heights, the predictions of the theory appear to be in qualitative agreement with the available data for the quantity of air entrained, but the theory needs to be extended in the case of large drop heights, when the expansion of the jet of particles is large. In a second part, the description of an expanded jet of particles is experimentally studied with PIV measurements. The data obtained are well fitted by the model by Liu, when the entrainment constant is taken as the angle of expansion of the jet obtained from the velocity field

Le mouillage dynamique des fibres

International audienceWe discuss how a solid (especially a fiber) is coated when drawn out of a bath of liquid. 1. For slow withdrawals out of pure viscous liquids, the data are found to be fitted by the famous Landau law: then, the coating results from a balance between viscosity and capillarity. For quicker withdrawals, the thickness of the entrained film suddenly diverges, at a velocity on order 1 m/s. Inertia is shown to be responsible for this effect. At still higher velocities, the thickness decreases with the velocity because the solid can only entrain the viscous boundary layer. 2. For complex fluids, surface effects are found in the low velocity regime: out of a surfactant solution, films are thicker than predicted by Landau, by a factor of order 2. The thickening factor is shown to be fixed by the Marangoni flow due to the presence of surfactants; out of an emulsion, the film can be enriched with oil, which can be understood by a simple model of capture; out of a polymer solution, a strong swelling of the film is observed if normal stresses are present. Hence, the problem has two families of solution: (i) at low velocity, the thickness of the layer is fixed by a balance between viscous and surface forces and thus is sensitive to the presence of surfactants, or other heterogeneities; (ii) at high velocity, inertia must be considered and the film thickness is fixed by the bulk properties of the liquid (density and viscosity). In these regimes, it is not affected by the presence of surfactants in the bath