Wear and Friction Modeling on Lifeboat Launch Systems

The RNLI provides search and rescue cover along the UK and RoI coast using a variety of lifeboats and launch techniques. In locations where there is no natural harbour it is necessary to use a slipway to launch the lifeboat into the sea. Lifeboat slipway stations consist of an initial section where the boat is held on rollers followed by an inclined keelway lined with low friction composite materials, the lifeboat is released from the top of the slipway and proceeds under its own weight into the water. The lifeboat is later recovered using a winch line. It is common to manually apply grease to the composite slipway lining before each launch and recovery in order to ensure sufficiently low friction for successful operation. With the introduction of the Tamar class lifeboat it is necessary to upgrade existing boathouses and standardise slipway operational procedures to ensure consistent operation. The higher contact pressures associated with the new lifeboat have led to issues of high friction and wear on the composite slipway linings and the manual application of grease to reduce friction is to be restricted due to environmental impact and cost factors. This paper presents a multidisciplinary approach to modelling slipway panel wear and friction using tribometer testing in conjunction with finite element analysis and slipway condition surveys to incorporate common real-world effects such as panel misalignments. Finally, it is shown that a freshwater lubrication system is effective, reducing cost and environmental impacts while maintaining good friction and wear performance

High temperature superconducting thin film microwave circuits: Fabrication, characterization, and applications

Epitaxial YBa2Cu3O7 films were grown on several microwave substrates. Surface resistance and penetration depth measurements were performed to determine the quality of these films. Here the properties of these films on key microwave substrates are described. The fabrication and characterization of a microwave ring resonator circuit to determine transmission line losses are presented. Lower losses than those observed in gold resonator circuits were observed at temperatures lower than critical transition temperature. Based on these results, potential applications of microwave superconducting circuits such as filters, resonators, oscillators, phase shifters, and antenna elements in space communication systems are identified

Process of making thin film 2H .alpha.-sic by laser ablation

Thin films of 2H .alpha.-silicon carbide are produced by pulsed laser ablation

Millimeter wave transmission studies of YBa2Cu3O7-delta thin films in the 26.5 to 40.0 GHz frequency range

Millimeter wave transmission measurements through YBa2Cu3O(7-delta) thin films on MgO, ZrO2 and LaAlO3 substrates, are reported. The films (approx. 1 micron) were deposited by sequential evaporation and laser ablation techniques. Transition temperatures T sub c, ranging from 89.7 K for the Laser Ablated film on LaAlO3 to approximately 72 K for the sequentially evaporated film on MgO, were obtained. The values of the real and imaginary parts of the complex conductivity, sigma 1 and sigma 2, are obtained from the transmission data, assuming a two fluid model. The BCS approach is used to calculate values for an effective energy gap from the obtained values of sigma sub 1. A range of gap values from 2 DELTA o/K sub B T sub c = 4.19 to 4.35 was obtained. The magnetic penetration depth is evaluated from the deduced values of sigma 2. These results are discussed together with the frequency dependence of the normalized transmission amplitude, P/P sub c, below and above T sub c

Dynamics, dynamic soft elasticity and rheology of smectic-C elastomers

We present a theory for the low-frequency, long-wavelength dynamics of soft smectic-C elastomers with locked-in smectic layers. Our theory, which goes beyond pure hydrodynamics, predicts a dynamic soft elasticity of these elastomers and allows us to calculate the storage and loss moduli relevant for rheology experiments as well as the mode structure.Comment: 4 pages, 2 figure

Deformed Gaussian Orthogonal Ensemble Analysis of the Interacting Boson Model

A Deformed Gaussian Orthogonal Ensemble (DGOE) which interpolates between the Gaussian Orthogonal Ensemble and a Poissonian Ensemble is constructed. This new ensemble is then applied to the analysis of the chaotic properties of the low lying collective states of nuclei described by the Interacting Boson Model (IBM). This model undergoes a transition order-chaos-order from the $SU(3)$ limit to the $O(6)$ limit. Our analysis shows that the quantum fluctuations of the IBM Hamiltonian, both of the spectrum and the eigenvectors, follow the expected behaviour predicted by the DGOE when one goes from one limit to the other.Comment: 10 pages, 4 figures (avaiable upon request), IFUSP/P-1086 Replaced version: in the previous version the name of one of the authors was omitte

Performance and modeling of superconducting ring resonators at millimeter-wave frequencies

Microstrip ring resonators operating at 35 GHz were fabricated from laser ablated YBCO thin films deposited on lanthanum aluminate substrates. They were measured over a range of temperatures and their performance compared to identical resonators made of evaporated gold. Below 60 Kelvin the superconducting strip performed better than the gold, reaching an unloaded Q approximately 1.5 times that of gold at 25 K. A shift in the resonant frequency follows the form predicted by the London equations. The Phenomenological Loss Equivalence Method is applied to the ring resonator and the theoretically calculated Q values are compared to the experimental results