Surface wave dispersion in cement-based media: Inclusion size effect

Abstract This paper presents the experimental study of surface wave propagation in cementitious material with different shape and size but same volume content of thin inclusions that simulate distributed damage. The Rayleigh wave velocity changes almost up to 20% depending on the inclusion shape, while the longitudinal velocity, the experimental variance, as well as the coherence of the signals is also affected. It is demonstrated that the material is strongly dispersive and caution should be taken for the interpretation of the wave measurements since the velocity is sensitive not only to the damage content but also to the ''crack'' size.

Application of Acoustic Emission on the Characterization of Fracture in Textile Reinforced Cement Laminates

This work studies the acoustic emission (AE) behavior of textile reinforced cementitious (TRC) composites under flexural loading. The main objective is to link specific AE parameters to the fracture mechanisms that are successively dominating the failure of this laminated material. At relatively low load, fracture is initiated by matrix cracking while, at the moment of peak load and thereafter, the fiber pull-out stage is reached. Stress modeling of the material under bending reveals that initiation of shear phenomena can also be activated depending on the shape (curvature) of the plate specimens. Preliminary results show that AE waveform parameters like frequency and energy are changing during loading, following the shift of fracturing mechanisms. Additionally, the AE behavior of specimens with different curvature is very indicative of the stress mode confirming the results of modeling. Moreover, AE source location shows the extent of the fracture process zone and its development in relation to the load. It is seen that AE monitoring yields valuable real time information on the fracture of the material and at the same time supplies valuable feedback to the stress modeling

Damage Accumulation in Cyclically-Loaded Glass-Ceramic Matrix Composites Monitored by Acoustic Emission

Barium osumilite (BMAS) ceramic matrix composites reinforced with SiC-Tyranno fibers are tested in a cyclic loading protocol. Broadband acoustic emission (AE) sensors are used for monitoring the occurrence of different possible damage mechanisms. Improved use of AE indices is proposed by excluding low-severity signals based on waveform parameters, rather than only threshold criteria. The application of such improvements enhances the accuracy of the indices as accumulated damage descriptors. RA-value, duration, and signal energy follow the extension cycles indicating moments of maximum or minimum strain, while the frequency content of the AE signals proves very sensitive to the pull-out mechanism

Acoustic emission behavior of steel fibre reinforced concrete under bending

a b s t r a c t The present paper describes the acoustic emission (AE) behavior of concrete under four-point bending. Steel fibres of varying content were used as reinforcement in concrete slabs and their influence on the fracture process and the acoustic activity was investigated. The total acoustic emission (AE) activity was found to be directly proportional to the fibre content. Analysis revealed that particular AE parameters change monotonically with the progress of damage and can be used for the characterization of the failure process

Quantitative analysis of left atrial function in asymptomatic patients with b-thalassemia major using real-time three-dimensional echocardiography

<p>Abstract</p> <p>Background</p> <p>There is strong evidence that left atrial (LA) size is a prognostic marker in a variety of heart diseases. Recently, real-time three-dimensional echocardiography (RT3DE) has been reported as a useful tool for studying the phasic changes of the left atrial volumes. The aim of this study was to investigate the performance of the left atrium in beta-thalassemic patients with preserved left ventricular ejection fraction (EF) and no iron overload, using RT3DE.</p> <p>Methods</p> <p>Twenty-eight asymptomatic b-thalassemic patients (32.2 ± 4.3 years old, 17 men) who were on iron chelating therapy, as well as 20 age- and sex-matched healthy controls underwent transthoracic RT3DE. The patient group had normal echocardiographic systolic and diastolic indices, while there was no myocardial iron disposition according to MRI. Apical full volume data sets were obtained and LA volumes were measured at 3 time points of the cardiac cycle: (1) maximum volume (LAmax) at end-systole, just before mitral valve opening; (2) minimum volume (LAmin) at end-diastole, just before mitral valve closure; and (3) volume before atrial active contraction (LApreA) obtained from the last frame before mitral valve reopening or at time of the P wave on the surface electrocardiogram. From the derived values, left atrial active and passive emptying volumes, as well as the respective emptying fractions were calculated.</p> <p>Results</p> <p>Left ventricular EF (59.2 ± 2.5% patients vs. 60.1 ± 2.1% controls), E/A, E/E' were similar between the two groups. Differences in the LAmax, LAmin and LApreA between b-thalassemic patients and controls were non-significant, LAmax:(35.5 ± 13.4 vs 31.8 ± 9.8)cm³, LAmin:(16.0 ± 6.0 vs. 13.5 ±4.2)cm³, and LApreA:(25.4 ± 9.8 vs. 24.3 ± 7.2)cm³. However, left atrial active emptying fraction was reduced in the patient group as compared to the healthy population (34.3 ± 16.4% vs. 43.2 ± 11.4%, p < 0.05).</p> <p>Conclusion</p> <p>RT3DE may be a novel technique for the evaluation of LA function in asymptomatic patients with b-Thalassemia Major. Among three-dimensional volumes and indices, left atrial active emptying fraction may be an early index of LA dysfunction in the specific patient population.</p

Valorisation of sawdust through the combined microwave-assisted hydrothermal pre-treatment and fermentation using an oleaginous yeast

Oleaginous yeast, cultured on second-generation lignocellulosic resources, has the potential to be a key part of the future energy sector. However, the multiple unit operations necessary to produce concentrated hydrolysates, with a minimum of fermentation inhibitors, limit the applicability to date. In this study, a simple microwave-assisted hydrothermal pre-treatment step of oak or beech sawdust was deployed to produce an oligosaccharide-rich hydrolysate. This was then catabolised by the oleaginous yeast, Metschnikowia pulcherrima, avoiding the need for costly enzymatic or further chemical steps in the processing. Up to 85% of the sawdust’s hemicelluloses could be solubilised under these conditions, and 8 g/L DCW yeast with a 42% lipid content produced. While a number of studies have demonstrated that oleaginous yeasts possess high inhibitor tolerance, using this real lignocellulosic hydrolysate, we demonstrate that lipid production is actually very sensitive to inhibitor and carbon availability, and the optimal system is not the one that gives the highest hydrolysate or cell biomass. Indeed, the yeast was shown to detoxify the inhibitors in the process, but at high inhibitor loading, this leads to very poor lipid production, especially at high furfural levels. These findings clearly highlight the importance of considering multiple variables when real, complex lignocellulosic media are involved, tuning process conditions based on the desired fermentation outcomes

Wave propagation in cementitious material containing artificial distributed damage

The propagation of ultrasonic pulses through highly inhomogeneous mortar is discussed in this paper. The inhomogeneity is introduced by light plastic inclusions in different volume contents to simulate distributed damage. Wave propagation in such media becomes dispersive and therefore, although pulse velocity is influenced, other easily measured features are much more indicative of the inclusion content. These features can certainly improve characterization since they include information from the whole waveform and not only the leading edge