19,844 research outputs found
Method for forming hermetic seals
The firmly adherent film of bondable metal, such as silver, is applied to the surface of glass or other substrate by decomposing a layer of solution of a thermally decomposable metallo-organic deposition (MOD) compound such as silver neodecanoate in xylene. The MOD compound thermally decomposes into metal and gaseous by-products. Sealing is accomplished by depositing a layer of bonding metal, such as solder or a brazing alloy, on the metal film and then forming an assembly with another high melting point metal surface such as a layer of Kovar. When the assembly is heated above the temperature of the solder, the solder flows, wets the adjacent surfaces and forms a hermetic seal between the metal film and metal surface when the assembly cools
Status of SEMI's solar-grade substrate standards
A proposal for a standard specifications listing covering requirements for silicon wafers used in solar cell manufacturing is outlined. The specific contents of the general requirements specifications include: ordering information; dimensions and permissible variations; material and manufacture; physical parameters; sampling; test methods; certification; and packaging and marking
Land use analysis of US urban areas using high-resolution imagery from Skylab
The author has identified the following significant results. The S-190B imagery from Skylab 3 permitted the detection of higher levels of land use detail than any satellite imagery previously evaluated using manual interpretation techniques. Resolution approaches that of 1:100,000 scale infrared aircraft photography, especially regarding urban areas. Nonurban areas are less distinct
Module degradation catalyzed by metal-encapsulation reactions
Four major properties are considered to be relevant in determining service life of a photovoltaic module: (1) Mechanical: creep resistance, modulus, tensile strength; (2) Optical: integrated transmission at 0.4 to 1.1 m wavelength; (3) Chemical: inertness with respect to metals and other components, retention of stabilizers, etc. and (4) Electrical; maintaining effective isolation of conductive components. These properties were measured after exposing polymer specimens to three types of accelerated stress: thermal, ultraviolet radiation and metal catalysts. These conditions give rise to a large number of complex interrelated free-radical reactions that result in the deterioration of polymeric materials
Technique for producing bipolar and MOS field effect transistors on a single chip
Several cycles of photoetching, dopant deposition, and drive-in produce selectively-doped regions and semiconductor junctions within a single chip
Stop-list slicing.
Traditional program slicing requires two parameters: a program location and a variable, or perhaps a set of variables, of interest. Stop-list slicing adds a third parameter to the slicing criterion: those variables that are not of interest. This third parameter is called the stoplist. When a variable in the stop-list is encountered, the data-flow dependence analysis of slicing is terminated for that variable. Stop-list slicing further focuses on the computation of interest, while ignoring computations known or determined to be uninteresting. This has the potential to reduce slice size when compared to traditional forms of slicing. In order to assess the size of the reduction obtained via stop-list slicing, the paper reports the results of three empirical evaluations: a large scale empirical study into the maximum slice size reduction that can be achieved when all program variables are on the stop-list; a study on a real program, to determine the reductions that could be obtained in a typical application; and qualitative case-based studies to illustrate stop-list slicing in the small. The large-scale study concerned a suite of 42 programs of approximately 800KLoc in total. Over 600K slices were computed. Using the maximal stoplist reduced the size of the computed slices by about one third on average. The typical program showed a slice size reduction of about one-quarter. The casebased studies indicate that the comprehension effects are worth further consideration
Increased voltage photovoltaic cell
A photovoltaic cell, such as a solar cell, is provided which has a higher output voltage than prior cells. The improved cell includes a substrate of doped silicon, a first layer of silicon disposed on the substrate and having opposite doping, and a second layer of silicon carbide disposed on the first layer. The silicon carbide preferably has the same type of doping as the first layer
Low-pressure, chemical vapor deposition polysilicon
The low-pressure chemical vapor deposition (LPCVD) of polycrystalline silicon was investigted. The physical system was described, as was the controlling process parameters and requirements for producing films for use as an integral portion of the solar cell contact system
- …