Satellite and ground radiotracking of elk

Radiotracking and monitoring of free-living animals in natural environments is providing an effective new technique for acquiring information on biological processes, including animal orientation and navigation. To test the practicability of extending the technique by using satellite systems for tracking animals, a female elk was instrumented with an electronic collar. It contained both the Interrogation Recording Location System (IRLS) transponder and a Craighead-Varney ground-tracking transmitter. The elk was successfully tracked and monitored by satellite during month of April 1970. This was the first time an animal had been tracked by satellite on the surface of the earth

Grizzly bear habitat analysis. Section 2: Evaluation of grizzly bear food plants, food categories and habitat

There are no author-identified significant results in this report

Design, development and mechanization of a precision deployable truss with optimized structural efficiency for spaceborne applications

A deployable mast concept which meets the weight, size and stability requirements for a feed support structure for offset antennas up to 100 meters in diameter is discussed. A triangulated truss configuration, the use of tapered tubes which exhibit a high strength-to-weight ratio, and low CTE graphite-epoxy material are seen to provide an efficient, lightweight and stable truss suitable for an antenna feed support. A low stowage ratio of 30:1 is achieved through a unique preloaded hinge located at the center of each longeron and an autonomous deployment cage with a drive mechanism. Initial analysis and proof of concept hardware validated the basic mechanism and design assumptions and provided a basis for further investigation. The concept can readily accept variations in member size and thus lends itself to optimization for other potential uses where a stiff, lightweight deployable truss is needed

The Application of a Cylindrical-spherical Floating Ring Bearing as a Device to Control Stability of Turbogenerators

The development of a new device to control stability of turbogenerators is described. The device comprises a floating ring installed between the journal and bearing housing of a fluid film bearing. The journal and the inner surface of the ring are cylindrical while the outer surface of the ring and bearing surface are spherical providing axial location of the ring and self-alignment of the bearing. The employment of this device would lead to a consistent machine performance. System stability may be controlled by changing a number of bearing and floating ring parameters. This device also offers an additional advantage of having a very low frictional characteristic. A feasibility study was carried out to investigate the suitability of the new device to turbogenerator applications. Both theoretical analysis and experimental observations were carried out. Initial results suggest that the new floating ring device is a competitive alternative to other conventional arrangements

Monitoring wood decay in poles by the vibroacoustic method

Despite recent advances in the development of new materials, wood continues to be used globally for the support of overhead cable networks used by telecommunications and electrical utility companies. As a natural material, wood is subject to decay and will eventually fail, causing disruption to services and danger to public and company personnel. The traditional method of testing poles for decay involves hitting them with a hammer and listening to the sound that results. However, evidence suggests that a large number of poles are replaced unnecessarily and a significant number of poles continue to fail unexpectedly in service. Therefore, a more accurate method for assessing the structural integrity of wooden poles is required. The underlying physical principles behind the 'pole tester's approach' have been identified and used in the development of a decay meter to enable objective monitoring of decay in wooden poles

Fabrication of small laterally patterned multiple quantum wells

A technique of high voltage electron beam lithography and BCI_3/Ar reactive ion etching for laterally patterning GaAs/Al_0_3 Ga_(0.7) As multiple quantum wells is described. The resulting structures were analyzed using scanning electron microscopy and a novel reflection electron microscopy technique, and their geometries are shown. Narrow columns 40 nm in diameter etched 230 nm through the quantum wells were reproducibly fabricated

Effect of vasopressin 1b receptor blockade on the hypothalamic-pituitary-adrenal response of chronically stressed rats to a heterotypic stressor

Exposure to chronic restraint (CR) modifies the hypothalamic–pituitary–adrenal (HPA) axis response to subsequent acute stressors with adaptation of the response to a homotypic and sensitization of the response to a heterotypic stressor. Since vasopressin (AVP) activity has been reported to change during chronic stress, we investigated whether this was an important factor in HPA facilitation. We therefore tested whether vasopressin 1b receptor (AVPR1B) blockade altered the ACTH and corticosterone response to heterotypic stressors following CR stress. Adult male rats were exposed to CR, single restraint, or were left undisturbed in the home cage. Twenty-four hours after the last restraint, rats were injected with either a AVPR1B antagonist (Org, 30 mg/kg, s.c.) or vehicle (5% mulgofen in saline, 0.2/kg, s.c.) and then exposed to either restraint, lipopolysaccharide (LPS) or white noise. CR resulted in the adaptation of the ACTH and corticosterone response to restraint and this effect was not prevented by pretreatment with Org. Although we found no effect of CR on LPS-induced ACTH and corticosterone secretion, both repeated and single episodes of restraint induced the sensitization of the ACTH, but not corticosterone response to acute noise. Pretreatment with Org reduced the exaggerated ACTH response to noise after both single and repeated exposure to restraint

Topical Menthol Application Augments Cutaneous Microvascular Blood Flow

Please refer to the pdf version of the abstract located adjacent to the title

Ultranarrow conducting channels defined in GaAs-AlGaAs by low-energy ion damage

We have laterally patterned the narrowest conducting wires of two-dimensional electron gas (2DEG) material reported to date. The depletion induced by low-energy ion etching of GaAs-AlGaAs 2DEG structures was used to define narrow conducting channels. We employed high voltage electron beam lithography to create a range of channel geometries with widths as small as 75 nm. Using ion beam assisted etching by Cl2 gas and Ar ions with energies as low as 150 eV, conducting channels were defined by etching only through the thin GaAs cap layer. This slight etching is sufficient to entirely deplete the underlying material without necessitating exposure of the sidewalls that results in long lateral depletion lengths. At 4.2 K, without illumination, our narrowest wires retain a carrier density and mobility at least as high as that of the bulk 2DEG and exhibit quantized Hall effects. Aharonov–Bohm oscillations are seen in rings defined by this controlled etch-damage patterning. This patterning technique holds promise for creating one-dimensional conducting wires of even smaller sizes