The Aims of the Criminal Law

Cu2ZnSnS4(CZTS) is an interesting material for sustainable photovoltaics, but efficiencies are limitedby the low open-circuit voltage. A possible cause of this is disorder among the Cu and Zn cations, aphenomenon which is difficult to detect by standard techniques. We show that this issue can beovercome using near-resonant Raman scattering, which lets us estimate a critical temperature of 533±10 K for the transition between ordered and disordered CZTS. These findings have deepsignificance for the synthesis of high-quality material, and pave the way for quantitative investigationof the impact of disorder on the performance of CZTS-based solar cells.kestCa

Surface oxide on thin films of yttrium hydride studied by neutron reflectometry

The applicability of standard methods for compositional analysis is limited for H-containing films. Neutron reflectometry is a powerful, non-destructive method that is especially suitable for these systems due to the large negative scattering length of H. In this work we demonstrate how neutron reflectometry can be used to investigate thin films of yttrium hydride. Neutron reflectometry gives a strong contrast between the film and the surface oxide layer, enabling us to estimate the oxide thickness and oxygen penetration depths. A surface oxide layer of 5-10 nm thickness was found for unprotected yttrium hydride films

“It Keeps Going and Going and Going”: The Expansion of False Advertising Litigation Under the Lanham Act

To improve the conduction band alignment and explore the influence of the buffer-absorber interface, we here investigate an alternative buffer for Cu2ZnSnS4 (CZTS) solar cells. The Zn(O, S) system was chosen since the optimum conduction band alignment with CZTS is predicted to be achievable, by varying oxygen to sulfur ratio. Several sulfur to oxygen ratios were evaluated to find an appropriate conduction band offset. There is a clear trend in open-circuit voltage Voc, with the highest values for the most sulfur rich buffer, before going to the blocking ZnS, whereas the fill factor peaks at a lower S content. The best alternative buffer cell in this series had an efficiency of 4.6% and the best CdS reference gave 7.3%. Extrapolating Voc values to 0 K gave activation energies well below the expected bandgap of 1.5 eV for CZTS, which indicate that recombination at the interface is dominating. However, it is clear that the values are affected by the change of buffer composition and that increasing sulfur content of the Zn(O, S) increases the activation energy for recombination. A series with varying CdS buffer thickness showed the expected behavior for short wavelengths in quantum efficiency measurements but the final variation in efficiency was small

Back and front contacts in kesterite solar cells: state-of-the-art and open questions

We review the present state-of-the-art within back and front contacts in kesterite thin film solar cells, as well as the current challenges. At the back contact, molybdenum (Mo) is generally used, and thick Mo(S, Se)2 films of up to several hundred nanometers are seen in record devices, in particular for selenium-rich kesterite. The electrical properties of Mo(S, Se)2 can vary strongly depending on orientation and indiffusion of elements from the device stack, and there are indications that the back contact properties are less ideal in the sulfide as compared to the selenide case. However, the electronic interface structure of this contact is generally not well-studied and thus poorly understood, and more measurements are needed for a conclusive statement. Transparent back contacts is a relatively new topic attracting attention as crucial component in bifacial and multijunction solar cells. Front illuminated efficiencies of up to 6% have so far been achieved by adding interlayers that are not always fully transparent. For the front contact, a favorable energy level alignment at the kesterite/CdS interface can be confirmed for kesterite absorbers with an intermediate [S]/([S]+[Se]) composition. This agrees with the fact that kesterite absorbers of this composition reach highest efficiencies when CdS buffer layers are employed, while alternative buffer materials with larger band gap, such as Cd1−xZnxS or Zn1−xSnxOy, result in higher efficiencies than devices with CdS buffers when sulfur-rich kesterite absorbers are used. Etching of the kesterite absorber surface, and annealing in air or inert atmosphere before or after buffer layer deposition, has shown strong impact on device performance. Heterojunction annealing to promote interdiffusion was used for the highest performing sulfide kesterite device and air-annealing was reported important for selenium-rich record solar cells

A new thin film photochromic material: Oxygen-containing yttrium hydride

In this work we report on photochromism in transparent thin film samples of oxygen-containing yttrium hydride. Exposure to visible and ultraviolet (UV) light at moderate intensity triggers a decrease in the optical transmission of visible and infrared (IR) light. The photo-darkening is colour-neutral. We show that the optical transmission of samples of 500 nm thickness can be reduced by up to 50% after one hour of illumination with light of moderate intensity. The reaction is reversible and samples that are left in the dark return to the initial transparent state. The relaxation time in the dark depends on the temperature of the sample and the duration of the light exposure. The photochromic reaction takes place under ambient conditions in the as-deposited state of the thin-film samples.Comment: Accepted for publication in Solar Energy Materials and Solar Cell

Band Alignment Between ZnO-Based and Cu(In,Ga)Se2 Thin Films for High Efficiency Solar Cells

Thin-film solar cells based on Cu(In,Ga)Se2 contain a thin buffer layer of CdS in their standard configuration. In order to avoid cadmium in the device for environmental reasons, Cd-free alternatives are investigated. In this thesis, ZnO-based films, containing Mg or S, grown by atomic layer deposition (ALD), are shown to be viable alternatives to CdS. The CdS is an n-type semiconductor, which together with the n-type ZnO top-contact layers form the pn-junction with the p-type Cu(In,Ga)Se2. From device modeling it is known that a buffer layer conduction band (CB) position of 0-0.4 eV above that of the Cu(In,Ga)Se2 layer is consistent with high photovoltaic performance. For the Cu(In,Ga)Se2/ZnO interface this position is measured by photoelectron spectroscopy and optical methods to –0.2 eV, resulting in increased interface recombination. By including sulfur into ZnO, a favorable CB position to Cu(In,Ga)Se2 can be obtained for appropriate sulfur contents, and device efficiencies of up to 16.4% are demonstrated in this work. From theoretical calculations and photoelectron spectroscopy measurements, the shift in the valence and conduction bands of Zn(O,S) are shown to be non-linear with respect to the sulfur content, resulting in a large band gap bowing. ALD is a suitable technique for buffer layer deposition since conformal coverage can be obtained even for very thin films and at low deposition temperatures. However, deposition of Zn(O,S) is shown to deviate from an ideal ALD process with much larger sulfur content in the films than expected from the precursor pulsing ratios and with a clear increase of sulfur towards the Cu(In,Ga)Se2 layer. For (Zn,Mg)O, single-phase ZnO-type films are obtained for Mg/(Zn+Mg) < 0.2. In this region, the band gap increases almost linearly with the Mg content resulting in an improved CB alignment at the heterojunction interface with Cu(In,Ga)Se2 and high device efficiencies of up to 14.1%

Band Alignment Between ZnO-Based and Cu(In,Ga)Se2 Thin Films for High Efficiency Solar Cells

Thin-film solar cells based on Cu(In,Ga)Se2 contain a thin buffer layer of CdS in their standard configuration. In order to avoid cadmium in the device for environmental reasons, Cd-free alternatives are investigated. In this thesis, ZnO-based films, containing Mg or S, grown by atomic layer deposition (ALD), are shown to be viable alternatives to CdS. The CdS is an n-type semiconductor, which together with the n-type ZnO top-contact layers form the pn-junction with the p-type Cu(In,Ga)Se2. From device modeling it is known that a buffer layer conduction band (CB) position of 0-0.4 eV above that of the Cu(In,Ga)Se2 layer is consistent with high photovoltaic performance. For the Cu(In,Ga)Se2/ZnO interface this position is measured by photoelectron spectroscopy and optical methods to –0.2 eV, resulting in increased interface recombination. By including sulfur into ZnO, a favorable CB position to Cu(In,Ga)Se2 can be obtained for appropriate sulfur contents, and device efficiencies of up to 16.4% are demonstrated in this work. From theoretical calculations and photoelectron spectroscopy measurements, the shift in the valence and conduction bands of Zn(O,S) are shown to be non-linear with respect to the sulfur content, resulting in a large band gap bowing. ALD is a suitable technique for buffer layer deposition since conformal coverage can be obtained even for very thin films and at low deposition temperatures. However, deposition of Zn(O,S) is shown to deviate from an ideal ALD process with much larger sulfur content in the films than expected from the precursor pulsing ratios and with a clear increase of sulfur towards the Cu(In,Ga)Se2 layer. For (Zn,Mg)O, single-phase ZnO-type films are obtained for Mg/(Zn+Mg) < 0.2. In this region, the band gap increases almost linearly with the Mg content resulting in an improved CB alignment at the heterojunction interface with Cu(In,Ga)Se2 and high device efficiencies of up to 14.1%