Development Of A Micro Water Grid (MWG) Pilot Platform For Green Buildings

The objectives of this Micro Water Grid (MWG) pilot platform project are to i) address the need for reliable municipal water supplies, ii) identify and strengthen vulnerable water system elements, and iii) design an optimal micro water grid pilot platform for green buildings. This paper describes the overall context of the MWG and considers appropriate analytical methods for water demand, hydraulic analysis and decision models for optimal MWG pilot platforms. This is an on-going research project and various MWG design scenarios, along with numerical results, will be presented as the research progresses

Experimental Study on Effects of Lubricant Oil in a Domestic Refrigerator-Freezer

Lubricant oil is essential for lubricating moving parts and cooling the components in a refrigerant compressor. However, the oil deteriorates heat transfer performance in the heat exchangers, and increases pressure drop in a refrigeration circuit. In this study, investigation of the effects of lubricant oil circulating in heat exchangers on the performance of the domestic refrigerator-freezer was carried out by performing some experiments. The experiments were conducted for conventional and oil-less systems with using a linear compressor in an environmental chamber to compare the cooling capacity, power consumption, and operating characteristics such as temperatures and pressures at inlets and outlets of each component, mass flow rate, and cooling time. The cooling capacity and power consumption of two systems were measured during the on-off cyclic tests. Comparing the experimental data for the conventional and the oil-less systems, the discharge temperature of the oil-less system is higher than that of the conventional system more than 20℃. However, due to the oil removal, the heat transfer performance was improved and the condenser outlet temperature was measured lower than the conventional about 1℃. The power consumption of the oil-less system was reduced by about 4.0% compared to the system with the lubricant oil

Abrupt metal-insulator transition observed in VO2 thin films induced by a switching voltage pulse

An abrupt metal-insulator transition (MIT) was observed in VO2 thin films during the application of a switching voltage pulse to two-terminal devices. Any switching pulse over a threshold voltage for the MIT of 7.1 V enabled the device material to transform efficiently from an insulator to a metal. The characteristics of the transformation were analyzed by considering both the delay time and rise time of the measured current response. The extrapolated switching time of the MIT decreased down to 9 ns as the external load resistance decreased to zero. Observation of the intrinsic switching time of the MIT in the correlated oxide films is impossible because of the inhomogeneity of the material; both the metallic state and an insulating state co-exist in the measurement volume. This indicates that the intrinsic switching time is in the order of less than a nanosecond. The high switching speed might arise from a strong correlation effect (Coulomb repulsion) between the electrons in the material.Comment: 5 pages, 5 figure

Temperature dependence of Mott transition in VO_2 and programmable critical temperature sensor

The temperature dependence of the Mott metal-insulator transition (MIT) is studied with a VO_2-based two-terminal device. When a constant voltage is applied to the device, an abrupt current jump is observed with temperature. With increasing applied voltages, the transition temperature of the MIT current jump decreases. We find a monoclinic and electronically correlated metal (MCM) phase between the abrupt current jump and the structural phase transition (SPT). After the transition from insulator to metal, a linear increase in current (or conductivity) is shown with temperature until the current becomes a constant maximum value above T_{SPT}=68^oC. The SPT is confirmed by micro-Raman spectroscopy measurements. Optical microscopy analysis reveals the absence of the local current path in micro scale in the VO_2 device. The current uniformly flows throughout the surface of the VO_2 film when the MIT occurs. This device can be used as a programmable critical temperature sensor.Comment: 4 pages, 3 figure

Observation of First-Order Metal-Insulator Transition without Structural Phase Transition in VO_2

An abrupt first-order metal-insulator transition (MIT) without structural phase transition is first observed by current-voltage measurements and micro-Raman scattering experiments, when a DC electric field is applied to a Mott insulator VO_2 based two-terminal device. An abrupt current jump is measured at a critical electric field. The Raman-shift frequency and the bandwidth of the most predominant Raman-active A_g mode, excited by the electric field, do not change through the abrupt MIT, while, they, excited by temperature, pronouncedly soften and damp (structural MIT), respectively. This structural MIT is found to occur secondarily.Comment: 4 pages, 4 figure

Electro-Mechanical Safety Testing of Portable ECG Devices for Home Healthcare Usage

OBJECTIVES: This paper suggests the experimental guidelines to evaluate the electro-mechanical safety of belt type equipment. The electro-mechanical safety was determined by using the International Electrotechnical Commission guidelines, which are widely used as important factors for assessing the electro-mechanical safety of belt type equipment. However, the local guidelines on wearable healthcare sensors are currently not well-established. Therefore, safety guidelines suited for the actual circumstances in Korea are required, and this paper attempts to try a new experimental safety test procedure of the wearable healthcare sensor. METHODS: This belt type device measures the electrocardiogram (ECG) and heart rates by attaching to the chest. Examination lists were selected by analyzing the common standards ofelectro-mechanical safety (IEC 60601-1) and environment tests (IEC 60068-1, IEC 60068-2) of home-healthcare equipment. RESULTS: The essential electrical safety, which was required for the RS300G3 as a medical device, was evaluated, and most of the examination lists were selected by considering the circumstances of the users. The device passed all the selected examinable lists that are applicable to the Korean environment. CONCLUSIONS: This study has limitations to estimate and to conduct electro-mechanical safety experiments because our study focused on the belt type of heart-rates equipment. We are not taking into account the overall electro-mechanical home-healthcare measurements. According to industrial and technological development, there are infinite possibilities for the advancement of home-healthcare equipment, so more examination lists for safety are being added in addition to what we have doneope