Free and Dissolved Gases in Castrocaro Spa Waters (Italy)

Free and dissolved gases in cold water samples from the Castrocaro spa, Northern Italy, were analyzed for their chemical composition. These gases were interpreted as the result of the binary mixing between a N2- and a CH4-rich component. CO2 is generally a minor constituent. N2/Ar ratios below the air typical value suggest that air saturated water (ASW) is the most likely source of atmospheric-derived components. This atmospheric end-member is predominant in low-salinity waters. Conversely, CH4-enriched gases are mainly associated with brackish to saline waters. The occurrence of minor amounts of light hydrocarbons (C2-C3) indicates a predominant biogenic origin of CH4. The He isotopic composition of the CH4-richest sample (3He/4He = 0.22 Ra) is in the range of values measured for cold seeps and mud volcanoes along the Northern Apennines foothills, and indicates a predominant crustal origin of this gas

Occurrence of ochratoxin a in different types of cheese offered for sale in Italy

The detection of Ochratoxin A (OTA) in the milk of ruminants occurs infrequently and at low levels, but its occurrence may be higher in dairy products such as cheese. The aim of this study was to investigate the presence of OTA in cheeses purchased in the metropolitan city of Bologna (Italy) and the surrounding area. For the analysis, a LC-MS/MS method with a limit of quantification (LOQ) of 1 µg/kg was used. OTA was detected in seven out of 51 samples of grated hard cheese (concentration range 1.3–22.4 µg/kg), while it was not found in the 33 cheeses of other types which were also analysed. These data show a low risk of OTA contamination for almost all types of cheese analysed. To improve the safety of cheese marketed in grated form, more regulations on cheese rind, which is the part most susceptible to OTA-producing moulds, should be implemented or, alternatively, producers should consider not using the rind as row material for grated cheese. It would be interesting to continue these investigations particularly on grated hard cheeses to have more data to update the risk assessment of OTA in cheese, as also suggested by EFSA in its 2020 scientific opinion on OTA

Characterization and possible astrophysics applications of UV sensitive SiPM devices

The National Institute of Nuclear Physics (INFN) is involved in the R&D of Silicon Photomultiplier (SiPM) sensors optimized to detect near-UV (NUV) photon radiation in low-intensity photons and high-precision time mesaurements, in collaboration with the Bruno Kessler Foundation (FBK). The performances of 6×6 mm2 NUV-HD SiPMs with 30×30 μm2 microcell area and the possible prospects for production and packaging of multi-sensor modules for astrophysical applications are discussed in this paper

Fabrication of a hydrogenated amorphous silicon detector in 3-d geometry and preliminary test on planar prototypes

Hydrogenated amorphous silicon (a-Si:H) can be produced by plasma-enhanced chemical vapor deposition (PECVD) of SiH4 (silane) mixed with hydrogen. The resulting material shows outstanding radiation hardness properties and can be deposited on a wide variety of substrates. Devices employing a-Si:H technologies have been used to detect many different kinds of radiation, namely, minimum ionizing particles (MIPs), X-rays, neutrons, and ions, as well as low-energy protons and alphas. However, the detection of MIPs using planar a-Si:H diodes has proven difficult due to their unsatisfactory S/N ratio arising from a combination of high leakage current, high capacitance, and limited charge collection efficiency (50% at best for a 30 µm planar diode). To overcome these limitations, the 3D-SiAm collaboration proposes employing a 3D detector geometry. The use of vertical electrodes allows for a small collection distance to be maintained while preserving a large detector thickness for charge generation. The depletion voltage in this configuration can be kept below 400 V with a consequent reduction in the leakage current. In this paper, following a detailed description of the fabrication process, the results of the tests performed on the planar p-i-n structures made with ion implantation of the dopants and with carrier selective contacts are illustrated

Selection of the silicon sensor thickness for the Phase-2 upgrade of the CMS Outer Tracker

During the operation of the CMS experiment at the High-Luminosity LHC the silicon sensors of the Phase-2 Outer Tracker will be exposed to radiation levels that could potentially deteriorate their performance. Previous studies had determined that planar float zone silicon with n-doped strips on a p-doped substrate was preferred over p-doped strips on an n-doped substrate. The last step in evaluating the optimal design for the mass production of about 200 m$^{2}$ of silicon sensors was to compare sensors of baseline thickness (about 300 μm) to thinned sensors (about 240 μm), which promised several benefits at high radiation levels because of the higher electric fields at the same bias voltage. This study provides a direct comparison of these two thicknesses in terms of sensor characteristics as well as charge collection and hit efficiency for fluences up to 1.5 × 10$^{15}$ n$_{eq}$/cm$^{2}$. The measurement results demonstrate that sensors with about 300 μm thickness will ensure excellent tracking performance even at the highest considered fluence levels expected for the Phase-2 Outer Tracker

Comparative evaluation of analogue front-end designs for the CMS Inner Tracker at the High Luminosity LHC

The CMS Inner Tracker, made of silicon pixel modules, will be entirely replaced prior to the start of the High Luminosity LHC period. One of the crucial components of the new Inner Tracker system is the readout chip, being developed by the RD53 Collaboration, and in particular its analogue front-end, which receives the signal from the sensor and digitizes it. Three different analogue front-ends (Synchronous, Linear, and Differential) were designed and implemented in the RD53A demonstrator chip. A dedicated evaluation program was carried out to select the most suitable design to build a radiation tolerant pixel detector able to sustain high particle rates with high efficiency and a small fraction of spurious pixel hits. The test results showed that all three analogue front-ends presented strong points, but also limitations. The Differential front-end demonstrated very low noise, but the threshold tuning became problematic after irradiation. Moreover, a saturation in the preamplifier feedback loop affected the return of the signal to baseline and thus increased the dead time. The Synchronous front-end showed very good timing performance, but also higher noise. For the Linear front-end all of the parameters were within specification, although this design had the largest time walk. This limitation was addressed and mitigated in an improved design. The analysis of the advantages and disadvantages of the three front-ends in the context of the CMS Inner Tracker operation requirements led to the selection of the improved design Linear front-end for integration in the final CMS readout chip