17,777 research outputs found
Experimental investigation at high subsonic speeds of the rolling-stability derivatives of a 1/22 scale model of the Republic F-105 airplane
Stability and control characteristics of an air-breathing missile configuration having a forward located inlet
An investigation was made to determine the aerodynamic characteristics of an airbreathing missile configuration having a forward located inlet. Control was provided by cruciform tail surfaces. Aerodynamic data were obtained for the body-tail configuration alone and with planar or cruciform wings. At Mach numbers from 2.86 to 4.63, the model had internal flow. At Mach numbers from 1.70 to 2.86, the internal duct was closed, and an inlet fairing was installed to simulate boost conditions
Wind-Tunnel Investigation of the Effect of Spin on the Aerodynamic Characteristics of a 60-Millimeter T-24 Mortar Shell with Several Tail-Fin Configurations
Energy efficient engine high-pressure turbine single crystal vane and blade fabrication technology report
The objective of the High-Pressure Turbine Fabrication Program was to demonstrate the application and feasibility of Pratt & Whitney Aircraft-developed two-piece, single crystal casting and bonding technology on the turbine blade and vane configurations required for the high-pressure turbine in the Energy Efficient Engine. During the first phase of the program, casting feasibility was demonstrated. Several blade and vane halves were made for the bonding trials, plus solid blades and vanes were successfully cast for materials evaluation tests. Specimens exhibited the required microstructure and chemical composition. Bonding feasibility was demonstrated in the second phase of the effort. Bonding yields of 75 percent for the vane and 30 percent for the blade were achieved, and methods for improving these yield percentages were identified. A bond process was established for PWA 1480 single crystal material which incorporated a transient liquid phase interlayer. Bond properties were substantiated and sensitivities determined. Tooling die materials were identified, and an advanced differential thermal expansion tooling concept was incorporated into the bond process
High power phase locked laser oscillators
The feasibility of mechanizing an adaptive array of independent laser oscillators for generation of a high power coherent output was experimentally investigated. Tests were structured to evaluate component/system requirements for delivery of energy to a low-earth orbit satellite. Initial experiments addressed the control issues of phase locking unstable resonators at low power levels. A successful phase lock demonstration formed the basis for the design and fabrication of the high power, water-cooled, control mirror subsequently installed in the NASA LeRC high power laser. Tests were performed to characterize the operational limits of the laser system and included quantitative assessment of the frequency stability, noise sources, and optical properties of the beam
Quantum Control of Qubits and Atomic Motion Using Ultrafast Laser Pulses
Pulsed lasers offer significant advantages over CW lasers in the coherent
control of qubits. Here we review the theoretical and experimental aspects of
controlling the internal and external states of individual trapped atoms with
pulse trains. Two distinct regimes of laser intensity are identified. When the
pulses are sufficiently weak that the Rabi frequency is much smaller
than the trap frequency \otrap, sideband transitions can be addressed and
atom-atom entanglement can be accomplished in much the same way as with CW
lasers. By contrast, if the pulses are very strong (\Omega \gg \otrap),
impulsive spin-dependent kicks can be combined to create entangling gates which
are much faster than a trap period. These fast entangling gates should work
outside of the Lamb-Dicke regime and be insensitive to thermal atomic motion.Comment: 16 pages, 15 figure
Inadequacy of Scaling Arguments for Neutrino Cross Sections
The problem with the use of scaling arguments for simultaneous studies of
different weak interaction processes is discussed. When different neutrino
scattering cross sections involving quite different momentum transfers are
being compared it difficult to define a meaningful single scaling factor to
renormalize calculated cross sections. It has been suggested that the use of
such scaling can be used to estimate high energy neutrino cross sections from
low energy neutrino cross sections. This argument has lead to questions on the
consistency of the magnitude of the LSND muon neutrino cross sections on
C relative to other lower energy weak processes. The issue is revisited
here and from inspection of the structure of the form factors involved it is
seen that the problem arises from a poor description of the transition form
factors at high momentum transfer. When wave functions that reproduce the
transverse magnetic inelastic (e,e') scattering form factor for the 15.11 MeV
state in C are used there is no longer a need for scaling the axial
current, and the different weak interactions rates involving the T=1 1
triplet in mass 12 are consistent with one another.Comment: 3 pages, 1 figur
Acoustic spectral analysis and testing techniques
Subjects covered in four reports are described including: (1) mathematical techniques for combining decibel levels of octaves or constant bandwidth: (2) techniques for determining equation for power spectral density function; (3) computer program to analyze acoustical test data; and (4) computer simulation of horn responses utilizing hyperbolic horn theory
Heterogeneity in the growth hormone pituitary gland system of rats and humans: Implications to microgravity based research
The cell separation techniques of velocity sedimentation, flow cytometry and continuous flow electrophoresis were used to obtain enriched populations of growth hormone (GH) cells. The goal was to isolate a GH cell subpopulation which releases GH molecules which are very high in biological activity, it was important to use a method which was effective in processing large numbers of cells over a short time span. The techniques based on sedimentation are limited by cell density overlaps and streaming. While flow cytometry is useful in the analytical mode for objectively establishing cell purity, the numbers of cells which can be processed in the sort mode are so small as to make this approach ineffective in terms of the long term goals. It was shown that continuous flow electrophoresis systems (CFES) can separate GH cells from other cell types on the basis of differences in surface charge. The bioreactive producers appear to be more electrophoretically mobile than the low producers. Current ground based CFES efforts are hampered by cell clumping in low ionic strength buffers and poor cell recoveries from the CFES device
- …