Photodetachment o F- by a few-cycle circularly polarized laser field

We report on calculations of the above threshold detachment of F- by a few-cycle circularly polarized laser field, discussing the effects of both the carrier-envelope relative phase and the number of the cycle contained in a pulse on the angular distribution of ejected photoelectron. The results are analyzed in terms of a two-step semiclassical model: after the electrons are detached through tunnelling their motion is determined by the electric field pulse according to the classical dynamics laws. Anisotropies in the angular distributions of the electrons ejected on the plane perpendicular to the laser propagation direction are found that depend on the number of cycle of the laser pulse

Polarization and angular distribution of the radiation emitted in laser-assisted recombination

The effect of an intense external linear polarized radiation field on the angular distributions and polarization states of the photons emitted during the radiative recombination is investigated. It is predicted, on symmetry grounds, and corroborated by numerical calculations of approximate recombination rates, that emission of elliptically polarized photons occurs when the momentum of the electron beam is not aligned to the direction of the oscillating field. Moreover, strong modifications to the angular distributions of the emitted photons are induced by the external radiation field.Comment: 5 pages, 3 figure

Experimental analysis of the influence of polymer solutions on performances and cavitation of small size pumps for professional appliances

Pumps used in professional appliances process a solution of water, soils residues and detergents. These affect vapor tension, viscosity and rheology of the solution, mainly due to the presence of surfactants and polymers. Only a few studies have been found on how these substances can influence pump performances. Therefore, an experimental analysis has been carried out with aqueous solutions of a detergent component, the Polyox WSR 301, in the concentration range of 100\u20137000 ppm, to evaluate their influence on pump performances and cavitation. Some properties of the solutions have been preliminary characterized with a rheometer. Then, each solution has been tested in a dedicated test rig, to compare the performance curves of a centrifugal pump used in professional warewashing machines with those obtained with pure water. A non-intrusive method, based on the investigation of high frequency vibrations and noise signals, has been developed to detect cavitation at its early stage of inception. It was observed that polymer mitigates cavitating pump vibrations, with a reduction of the acceleration to less than one g. The analysis has provided the data necessary for the successive development of a control strategy for pump operation in professional appliances

Cavitation Detection and Prevention in Professional Warewashing Machines

Cavitation is a phenomenon characterised by the presence of vapour bubbles in the fluid led by a local drop in pressure. In literature it is well known the impact on cavitation of pressure and temperature of pure water, but there are only few studies analysing how the presence of certain components of detergents and additives can influence the phenomenon. The impact of detergents and additives could be explained by the modified viscosity and rheology of the solution but also by the variation in the vapour tension. Most of these effects are due to the presence of surfactants and polymers in the solution. Cavitation in dynamic pumps is an important aspect that needs to be monitored and prevented, because it can cause damages affecting pump performances and inducing an increment in the level of vibration and noise. In professional warewashing machines, as for example the models of Electrolux Rack Type, this phenomenon can affect the operating functionalities of the machine. An experimental pump test rig has been realized with the aim of studying and monitoring the influence of these parameters on cavitation inception. This test rig permits measuring the pump performances at various operating conditions, in order to obtain its characteristic curves, and also forcing cavitation to measure its Net Positive Suction Head required (NPSHr) at different flow rates. The pump test rig allows also testing various configurations of the pump at different cavitation conditions, obtained by changing not only the suction pressure and temperature of the fluid but also its properties, adding detergents and additives. Cavitation inception can be detected measuring both the corresponding prevalence decrease and the change of vibration and noise level

The faster the narrower: characteristic bulk velocities and jet opening angles of Gamma Ray Bursts

The jet opening angle theta_jet and the bulk Lorentz factor Gamma_0 are crucial parameters for the computation of the energetics of Gamma Ray Bursts (GRBs). From the ~30 GRBs with measured theta_jet or Gamma_0 it is known that: (i) the real energetic E_gamma, obtained by correcting the isotropic equivalent energy E_iso for the collimation factor ~theta_jet^2, is clustered around 10^50-10^51 erg and it is correlated with the peak energy E_p of the prompt emission and (ii) the comoving frame E'_p and E'_gamma are clustered around typical values. Current estimates of Gamma_0 and theta_jet are based on incomplete data samples and their observed distributions could be subject to biases. Through a population synthesis code we investigate whether different assumed intrinsic distributions of Gamma_0 and theta_jet can reproduce a set of observational constraints. Assuming that all bursts have the same E'_p and E'_gamma in the comoving frame, we find that Gamma_0 and theta_jet cannot be distributed as single power-laws. The best agreement between our simulation and the available data is obtained assuming (a) log-normal distributions for theta_jet and Gamma_0 and (b) an intrinsic relation between the peak values of their distributions, i.e theta_jet^2.5*Gamma_0=const. On average, larger values of Gamma_0 (i.e. the "faster" bursts) correspond to smaller values of theta_jet (i.e. the "narrower"). We predict that ~6% of the bursts that point to us should not show any jet break in their afterglow light curve since they have sin(theta_jet)<1/Gamma_0. Finally, we estimate that the local rate of GRBs is ~0.3% of all local SNIb/c and ~4.3% of local hypernovae, i.e. SNIb/c with broad-lines.Comment: 15 pages, 8 figures, 1 table. Accepted for publication in MNRA

Transient model of a Professional Oven

Tackling the climate change by reducing energy consumption is among the biggest, most urgent challenges society is facing and requires a continuous efficiency improvement of thermal systems. Appropriate design strategies, developed a priori and then experimentally validated according to suitable test protocols on a prototype, are needed in order to reach potential energy saving targets. These strategies can successfully be implemented in the food service sector, where cooking appliances, in particular, present many possibilities for improving energy savings. Therefore, a valuable design methodology should take into account not only steady state operating conditions but also the transient behaviours of the device, which must be described by means of specially developed theoretical dynamic models. The operating profile of an oven, for example, consists of a sequence of unsteady phases (cavity heating-up, food introduction and extraction, switching from one cooking mode to another) interspersed with steady cooking phases. The dynamic model presented in this paper defines the energy conservation equations of a professional oven, where a high temperature thermal source positioned inside its cavity produces thermal power radiated and modulated over time, according to a suitable control strategy. In particular, when the temperature in the cooking zone of the cavity has reached a specified set point, this is thermostatically controlled in time, depending on the cooking phase. The resulting equation system is then solved by means of numerical methods. With this code, it is possible to support the design phase of both the structure and the control strategy of the oven. It permits, for example, to get a general understanding of the best possible configurations and combinations of insulation materials for the cavity walls or, with reference to the control strategy, to simulate different cooking procedures, with the aim of optimizing the operating sequence of the oven, reaching the maximum energy saving without reducing the cooking quality. The code, validated by comparison with a set of experimental data obtained with a current production model, will be applied in the design phase of a new line of high efficiency professional ovens