16,057 research outputs found
A comparative study of educational administration in Jamaica and in the United States of America.
Thesis (Ed.M.)--Boston Universit
Estimation of COVID-19 spread curves integrating global data and borrowing information
Currently, novel coronavirus disease 2019 (COVID-19) is a big threat to
global health. The rapid spread of the virus has created pandemic, and
countries all over the world are struggling with a surge in COVID-19 infected
cases. There are no drugs or other therapeutics approved by the US Food and
Drug Administration to prevent or treat COVID-19: information on the disease is
very limited and scattered even if it exists. This motivates the use of data
integration, combining data from diverse sources and eliciting useful
information with a unified view of them. In this paper, we propose a Bayesian
hierarchical model that integrates global data for real-time prediction of
infection trajectory for multiple countries. Because the proposed model takes
advantage of borrowing information across multiple countries, it outperforms an
existing individual country-based model. As fully Bayesian way has been
adopted, the model provides a powerful predictive tool endowed with uncertainty
quantification. Additionally, a joint variable selection technique has been
integrated into the proposed modeling scheme, which aimed to identify possible
country-level risk factors for severe disease due to COVID-19
Processing of laser formed SiC powder
Superior SiC characteristics can be achieved through the use of ideal constituent powders and careful post-synthesis processing steps. High purity SiC powders of approx. 1000 A uniform diameter, nonagglomerated and spherical were produced. This required major revision of the particle formation and growth model from one based on classical nucleation and growth to one based on collision and coalescence of Si particles followed by their carburization. Dispersions based on pure organic solvents as well as steric stabilization were investigated. Although stable dispersions were formed by both, subsequent part fabrication emphasized the pure solvents since fewer problems with drying and residuals of the high purity particles were anticipated. Test parts were made by the colloidal pressing technique; both liquid filtration and consolidation (rearrangement) stages were modeled. Green densities corresponding to a random close packed structure (approx. 63%) were achieved; this highly perfect structure has a high, uniform coordination number (greater than 11) approaching the quality of an ordered structure without introducing domain boundary effects. After drying, parts were densified at temperatures ranging from 1800 to 2100 C. Optimum densification temperatures will probably be in the 1900 to 2000 C range based on these preliminary results which showed that 2050 C samples had experienced substantial grain growth. Although overfired, the 2050 C samples exhibited excellent mechanical properties. Biaxial tensile strengths up to 714 MPa and Vickers hardness values of 2430 kg/sq mm 2 were both more typical of hot pressed than sintered SiC. Both result from the absence of large defects and the confinement of residual porosity (less than 2.5%) to small diameter, uniformly distributed pores
Processing of laser formed SiC powder
Processing research was undertaken to demonstrate that superior SiC characteristics could be achieved through the use of ideal constituent powders and careful post-synthesis processing steps. Initial research developed the means to produce approximately 1000 A uniform diameter, nonagglomerated, spherical, high purity SiC powders. Accomplishing this goal required major revision of the particle formation and growth model from one based on classical nucleation and growth to one based on collision and coalescence of Si particles followed by their carburization. Dispersions based on pure organic solvents as well as steric stabilization were investigated. Test parts were made by the colloidal pressing technique; both liquid filtration and consolidation (rearrangement) stages were modeled. Green densities corresponding to a random close packed structure were achieved. After drying, parts were densified at temperatures ranging from 1800 to 2100 C. This research program accomplished all of its major objectives. Superior microstructures and properties were attained by using powders having ideal characteristics and special post-synthesis processing procedures
Ion yields and erosion rates for Si1−xGex(0x1) ultralow energy O2+ secondary ion mass spectrometry in the energy range of 0.25–1 keV
We report the SIMS parameters required for the quantitative analysis of Si1−xGex across the range of 0 ≤ x ≤ 1 when using low energy O2+ primary ions at normal incidence. These include the silicon and germanium secondary ion yield [i.e., the measured ion signal (ions/s)] and erosion rate [i.e., the speed at which the material sputters (nm/min)] as a function of x. We show that the ratio Rx of erosion rates, Si1−xGex/Si, at a given x is almost independent of beam energy, implying that the properties of the altered layer are dominated by the interaction of oxygen with silicon. Rx shows an exponential dependence on x. Unsurprisingly, the silicon and germanium secondary ion yields are found to depart somewhat from proportionality to (1−x) and x, respectively, although an approximate linear relationship could be used for quantification across around 30% of the range of x (i.e., a reference material containing Ge fraction x would give reasonably accurate quantification across the range of ±0.15x). Direct comparison of the useful (ion) yields [i.e., the ratio of ion yield to the total number of atoms sputtered for a particular species (ions/atom)] and the sputter yields [i.e., the total number of atoms sputtered per incident primary ion (atoms/ions)] reveals a moderate matrix effect where the former decrease monotonically with increasing x except at the lowest beam energy investigated (250 eV). Here, the useful yield of Ge is found to be invariant with x. At 250 eV, the germanium ion and sputter yields are proportional to x for all x
Recommended from our members
BioNanoAdhesion: atomic force microscopy study of the electrostatic properties of pyridine-and imidazole-based polycationic surfaces
Self-assembled monolayers of pyridine- and imidazole-based disulfides are currently being produced on low roughness gold surfaces. The electrostatic interaction between these surfaces and an atomic force microscope cantilever, modified with a silica microparticle, will subsequently be investigated as a function of environmental pH. The results can be used towards the development of improved nanoparticulate non-viral gene delivery vectors
Report of the Rock Lobster Industry Advisory Committee meeting of 27 January 1987 - Report by the Chairman Mr. B.K. Bowen.
The Rock Lobster Industry Advisory Committee met in Perth on Tuesday 17 January 1987. Committee discussed the following: Policy on 5% pot loss on replacement of vessels less than six years old. Study of industry funded compensation mechanism for fishing capacity reductions. 20 Fathom rule. Future maintenance of the zone E boundary. The recreational Rock Lobster Fishery. Rock Lobster pot distribution. Options for a 10 per cent reduction in fishing effort. 1987 coastal tour. Augusta-Windy Harbour Rock Lobster Working Group. Report on the 1986/87 season
The materials processing research base of the Materials Processing Center
The goals and activities of the center are discussed. The center activities encompass all engineering materials including metals, ceramics, polymers, electronic materials, composites, superconductors, and thin films. Processes include crystallization, solidification, nucleation, and polymer synthesis
Introductory assessment of orbiting reflections for terrestrial power generation
The use of orbiting mirrors for providing energy to ground conversion stations to produce electrical power is shown to be a viable, cost effective and environmentally sound alternative to satellite solar power stations and conventional power sources. This is accomplished with the use of very light weight metal coated polymeric films as mirrors which, after deployment at 800 km, are placed in operational orbit and controlled by solar radiation pressure. Relations are developed showing the influence of a number of parameters (mirror altitude, orbit inclination, period, mirror size and number, and atmospheric effects) on the reflected insolation that may be received by a ground spot as a function of location. Some attractive alternative uses of the reflection are briefly discussed as a beneficial adjuncts to the system
- …