Optical control of an 8-element Ka-band phased array using a high-speed optoelectronic interconnect

Optical distribution of control signals in electronically steered phased array antennas is being considered. A demonstration experiment is described in which a high speed hybrid GaAs optoelectronic integrated circuit (OEIC) was used to control an eight element phased array antenna. The OEIC, which accepts a serial optical control signal as input and converts it to 16 demultiplexed parallel outputs, was used to control the monolithic GaAs phase shifters of a Ka-band patch panel array antenna. Antenna pattern switching speeds of 2.25 microsec, limited by interface circuitry, were observed

A high frequency GaAlAs travelling wave electro-optic modulator at 0.82 micrometers

Experimental GaAlAs modulators operating at 0.82 micrometers using a Mach-Zehnder interferometer configuration were designed and fabricated. Coplanar 50 ohm travelling wave microwave electrodes were used to obtain a bandwidth length product of 11.95 GHz-cm. The design, fabrication and dc performance of the GaAlAs travelling wave modulator is presented

Microwave characteristics of GaAs MMIC integratable optical detectors

Interdigitated photoconductive detectors were fabricated on microwave device structures, making them easily integratable with Monolithic Microwave Integrated Circuits (MMIC). Detector responsivity as high as 2.5 A/W and an external quantum efficiency of 3.81 were measured. Response speed was nearly independent of electrode geometry, and all detectors had usable response at frequencies to 6 GHz. A small signal model of the detectors based on microwave measurements was also developed

Capacity strengthening in malaria research: the Gates Malaria Partnership.

The Gates Malaria Partnership (GMP) includes five African and four European partner institutions. Its research programme has five priority areas involving an extensive range of field-based studies. GMP research has contributed significantly to the development of new research consortia investigating strategies for improving means of malaria control, and has already had an impact on policy and practice. A substantial investment in innovative training activities in malaria has enhanced knowledge and practice of malaria control at all levels from policy making to local community involvement. Capacity development, notably through a PhD programme, has been an underlying feature of all aspects of the programme

Measurement techniques for cryogenic Ka-band microstrip antennas

The measurement of cryogenic antennas poses unique logistical problems since the antenna under test must be embedded in a cooling chamber. A method of measuring the performance of cryogenic microstrip antennas using a closed cycle gas cooled refrigerator in a far field range is described. Antenna patterns showing the performance of gold and superconducting Ka-band microstrip antennas at various temperatures are presented

System architecture of MMIC-based large aperture arrays for space application

The persistent trend to use millimeter-wave frequencies for satellite communications presents the challenge to design large-aperture phased arrays for space applications. These arrays, which comprise 100 to 10,000 elements, are now possible due to the advent of lightwave technology and the availability of monolithic microwave integrated circuits. In this paper, system aspects of optically controlled array design are studied. In particular, two architectures for a 40 GHz array are outlined, and the main system-related issues are examined: power budget, synchronization in frequency and phase, and stochastic effects

Evaluation of LS-DYNA MAT162 for Modeling Composite Fastener Joints for High Rates of Loading

In the present work, the behavior of composite-fastener joints in bearing failure at dynamic stroke rates of 500 in/s, 300 in/s and 100 in/s has been evaluated through progressive damage analysis (PDA) material model in LS-DYNA, namely MAT162. Two joint types: titanium pin and Hi-Lok fastener were analyzed to identify the differences between without and with preload conditions. A meso-level approach where each lamina was modeled separately was employed and a contact definition based on fracture toughness data was defined to represent composite delamination behavior. Test fixture had been modeled in a detailed manner to account for the dynamic effects and the simulation results were validated against experimental data. Preliminary test-analysis correlation indicated that MAT162 predicted results conservatively when compared to tests. Debris accumulation were observed to greatly affect the test results which were not considered in the current modelling strategies

Fatal outcome in acute fatty liver of pregnancy and review of literature

Acute fatty liver of pregnancy (AFLP) is an uncommon life-threatening disorder of pregnancy seen commonly in third trimester. When not diagnosed at right time it can lead to hepatic failure, encephalopathy, coagulopathy, maternal and fetal mortality. The clinical symptoms and signs are nonspecific, and it needs to be identified early in order to prevent poor outcome. The gold standard for diagnosis of AFLP is liver biopsy, which is difficult in an acute setting and in abnormal coagulation profile hence the diagnosis is usually based on clinical criteria   Early termination of pregnancy and good intensive care support are the mainstay of management. The authors here presented a case report where even early delivery and good critical care failed to prevent maternal mortality. Review of literature regarding etiopathogenesis, management and recurrences of AFLP are also discussed

Analysis of Microstrip Lines with Alternative Implementation of Conductors and Superconductors

An analysis of microstrip line structures in which either the strip or the ground plane or both are made of a high Tc superconductor is presented. The effect of implementation of a superconductor to the strip and the ground plane is explained with the calculation of a conductor loss of the structure by the Phenomenological Loss Equivalence Method (PEM). The theoretical values are compared with the experimental results from a ring resonator which is made of a gold ground plane and a high Tc superconductor, YBa2Cu3O(7-x), strip

Conductor-backed coplanar waveguide resonators of Y-Ba-Cu-O and Tl-Ba-Ca-Cu-O on LaAlO3

Conductor-backed coplanar waveguide (CBCPW) resonators operating at 10.8 GHz have been fabricated from Tl-Ba-Ca-O (TBCCO) and Y-Ba-Cu-O (YBCO) thin films on LaAlO3. The resonators consist of a coplanar waveguide (CPW) patterned on the superconducting film side of the LaAlO3 substrate with a gold ground plane coated on the opposite side. These resonators were tested in the temperature range from 14 to 106 K. At 77 K, the best of our TBCCO and YBCO resonators have an unloaded quality factor (Qo) 7 and 4 times, respectively, larger than that of a similar all-gold resonator. In this study, the Qo's of the TBCCO resonators were larger than those of their YBCO counterparts throughout the aforementioned temperature range