36,168 research outputs found
Furthur development of the dynamic gas temperature measurement system
Candidate concepts capable of generating dynamic temperatures were identified and analyzed for use in verifying experimentally the frequency response of the dynamic gas temperature measurement system. A rotating wheel concept and one other concept will be selected for this purpose. Modifications to the data reduction code algorithms developed were identified and evaluated to reduce substantially the data reduction execution time. These modifications will be incorporated in a new data reduction program to be written in FORTRAN IV
Further development of the dynamic gas temperature measurement system
The objective of this effort was to experimentally verify a dynamic gas temperature measurement system in laboratory experiments. The dynamic gas temperature measurement system verification program is described. A brief description of the sensor geometry and construction is followed by a discussion of the probe heat transfer analysis and subsequent compensation method. The laboratory experiments are described and experimental results are discussed. Finally, directions for further investigation are given
Dynamic gas temperature measurement system
A gas temperature measurement system with compensated frequency response of 1 KHz and capability to operate in the exhaust of a gas turbine combustor was developed. Environmental guidelines for this measurement are presented, followed by a preliminary design of the selected measurement method. Transient thermal conduction effects were identified as important; a preliminary finite-element conduction model quantified the errors expected by neglecting conduction. A compensation method was developed to account for effects of conduction and convection. This method was verified in analog electrical simulations, and used to compensate dynamic temperature data from a laboratory combustor and a gas turbine engine. Detailed data compensations are presented. Analysis of error sources in the method were done to derive confidence levels for the compensated data
Dynamic gas temperature measurement system, volume 1
A gas temperature measurement system with compensated frequency response of 1 kHz and capability to operate in the exhaust of a gas turbine engine combustor was developed. A review of available technologies which could attain this objective was done. The most promising method was identified as a two wire thermocouple, with a compensation method based on the responses of the two different diameter thermocouples to the fluctuating gas temperature field. In a detailed design of the probe, transient conduction effects were identified as significant. A compensation scheme was derived to include the effects of gas convection and wire conduction. The two wire thermocouple concept was tested in a laboratory burner exhaust to temperatures of about 3000 F and in a gas turbine engine to combustor exhaust temperatures of about 2400 F. Uncompensated and compensated waveforms and compensation spectra are presented
Further development of the dynamic gas temperature measurement system. Volume 1: Technical efforts
A compensated dynamic gas temperature thermocouple measurement method was experimentally verified. Dynamic gas temperature signals from a flow passing through a chopped-wheel signal generator and an atmospheric pressure laboratory burner were measured by the dynamic temperature sensor and other fast-response sensors. Compensated data from dynamic temperature sensor thermoelements were compared with fast-response sensors. Results from the two experiments are presented as time-dependent waveforms and spectral plots. Comparisons between compensated dynamic temperature sensor spectra and a commercially available optical fiber thermometer compensated spectra were made for the atmospheric burner experiment. Increases in precision of the measurement method require optimization of several factors, and directions for further work are identified
Further development of the dynamic gas temperature measurement system
Two experiments for verifying the frequency response of a previously-developed dynamic gas temperature measurement system were performed. In both experiments, fine-wire resistance temperature sensors were used as standards. The compensated dynamic temperature sensor data will be compared with the standards to verify the compensation method. The experiments are described in detail
The SPAR thermal analyzer: Present and future
The SPAR thermal analyzer, a system of finite-element processors for performing steady-state and transient thermal analyses, is described. The processors communicate with each other through the SPAR random access data base. As each processor is executed, all pertinent source data is extracted from the data base and results are stored in the data base. Steady state temperature distributions are determined by a direct solution method for linear problems and a modified Newton-Raphson method for nonlinear problems. An explicit and several implicit methods are available for the solution of transient heat transfer problems. Finite element plotting capability is available for model checkout and verification
Critical current of a Josephson junction containing a conical magnet
We calculate the critical current of a
superconductor/ferromagnetic/superconductor (S/FM/S) Josephson junction in
which the FM layer has a conical magnetic structure composed of an in-plane
rotating antiferromagnetic phase and an out-of-plane ferromagnetic component.
In view of the realistic electronic properties and magnetic structures that can
be formed when conical magnets such as Ho are grown with a polycrystalline
structure in thin-film form by methods such as direct current sputtering and
evaporation, we have modeled this situation in the dirty limit with a large
magnetic coherence length (). This means that the electron mean free
path is much smaller than the normalized spiral length which in
turn is much smaller than (with as the length a complete
spiral makes along the growth direction of the FM). In this physically
reasonable limit we have employed the linearized Usadel equations: we find that
the triplet correlations are short ranged and manifested in the critical
current as a rapid oscillation on the scale of . These rapid
oscillations in the critical current are superimposed on a slower oscillation
which is related to the singlet correlations. Both oscillations decay on the
scale of . We derive an analytical solution and also describe a
computational method for obtaining the critical current as a function of the
conical magnetic layer thickness.Comment: Extended version of the published paper. Additional information about
the computational method is included in the appendi
Systematic design of dissipative and regenerative snubbers
Current commutation between diodes and switches is possible in hard-switching power stages over a wide di/dt range (10-1000+A/ mu s) with modern power devices and hardware practice. However, a definitive procedure does not exist for setting di/dt at diode reverse recovery. Diode turn-off performance is therefore examined, using IGBTs (insulated-gate bipolar transistors) to switch the diode current, to establish whether there exists an optimal di/dt that minimizes energy loss associated with diode recovery, when simple snubber-inductance reset circuits are used. Destructive parasitic oscillation, induced in inverse-parallel IGBTs across reverse-recovering freewheel diodes in IGBT modules, was observed during experimentation. The results indicate that snubberless power-stag
- …