Passively mode-locked laser using an entirely centred erbium-doped fiber

This paper describes the setup and experimental results for an entirely centred erbium-doped fiber laser with passively mode-locked output. The gain medium of the ring laser cavity configuration comprises a 3 m length of two-core optical fiber, wherein an undoped outer core region of 9.38 μm diameter surrounds a 4.00 μm diameter central core region doped with erbium ions at 400 ppm concentration. The generated stable soliton mode-locking output has a central wavelength of 1533 nm and pulses that yield an average output power of 0.33 mW with a pulse energy of 31.8 pJ. The pulse duration is 0.7 ps and the measured output repetition rate of 10.37 MHz corresponds to a 96.4 ns pulse spacing in the pulse train

Dual wavelength single longitudinal mode Ytterbium-doped fiber laser using a dual-tapered Mach-Zehnder interferometer

This paper describes a dual wavelength single longitudinal mode (SLM) demonstration for a proposed ytterbium-doped fiber laser. A dualtapered Mach-Zehnder interferometer (MZI) was inserted into the laser ring cavity setup to ensure a stable dual wavelength and SLM operation. The consequent dual wavelength lasing operation had a wavelength spacing of 0.94 nm and a side mode suppression ratio (SMSR) of 50 dB, with the linewidth of this setup measured as 294.15 kHz. A stability test allowed for a measurement of max power fluctuation as less than 0.8 dB for each wavelength and which was indicative of a stable dual wavelength operation

Effect of titanium dioxide (TiO₂) nanoparticle coating on the detection performance of microfiber knot resonator sensors for relative humidity measurement

In this study, the sensitivity and the linearity of the un-coated and TiO2-coated microfiber knot resonator (MKR) have been analyzed. The MKR is very sensitive to humidity changes since its refractive index is strongly humidity dependent. As a result, shifts occur in the resonance wavelength and there are also changes in output power. The un-coated MKR showed a sensitivity of 1.3 pm/%RH, in terms of the resonance wavelength, and a sensitivity of 0.0626 dB/%RH for the transmitted output power. The sensitivity increased greatly after the deposition of a porous TiO2 nanoparticle coating on the MKR. The TiO2-coated MKR showed an improved sensitivity of 2.5 pm/%RH, with respect to the resonance wavelength, and 0.0836 dB/%RH for the transmitted output power. This MKR sensor has the potential for use in a variety of humidity sensing applications

Application of graphene oxide based Microfiber-Knot resonator for relative humidity sensing

A relative humidity (RH) sensor is proposed and demonstrated using a micro-knot resonator (MKR) enhanced with a layer graphene oxide (GO) coating. The MKR is fabricated by means of tapering a standard fiber, with the GO coating added by the drop-cast method. The proposed sensor is tested for an RH range of between 0% and 80% at 20% intervals, and the configurations with and without the GO coating achieve sensitivities of 0.0104 nm/% and 0.0095 nm/%, respectively. The MKR configuration without the GO coating has a linear response correlation coefficient of 0.9098 and a resolution of 0.1%, while the configuration with the GO coating has a linear response correlation coefficient of 0.9548 and a resolution of 0.096% which is better. The proposed sensor has multiple applications, especially in the area of climate and atmospheric measurement and monitoring

Generation of stable and narrow spacing dual-wavelength ytterbium-doped fiber laser using a photonic crystal fiber

We demonstrate the design and operation of novel narrow spacing and stable dual-wavelength fiber laser (DWFL). A 70-cm ytterbium-doped fiber has been chosen as the gain medium in a ring cavity arrangement. Our design includes a short length photonic crystal fiber, acting as a dual-wavelength stabilizer based on its birefringence coefficient and nonlinear behavior and tunable band pass filter (TBPF) to achieve narrow spacing spectrum lasing. Our laser output is considered to be highly stable, with power fluctuation less than 0.8 dB over a period of 15 min. The flexibility and tunability of TBPF, together with polarization controller enable the spacing tuning of the DWFL from 0.03 nm up to 0.07 nm for 1040 nm region, and 0.10 nm up to 0.40 nm for 1060 nm region. The tunable wavelength spacing shows the flexibility of the DWFL in addition to stable and reliable properties of fiber laser in 1-m region

Bi2Te3 based passively Q-switched at 1042.76 and 1047 nm wavelength

In this paper, we propose and demonstrate the generation of dual wavelength based photonic crystal fiber passively Q-switched using few-layer TI:Bi2Te3 (bismuth telluride) saturable absorbers in a 1 micron waveband. The system employs a few-layer bismuth, induced onto a fiber ferrule using a dry oven method. A centered dual-wavelength output at 1042.76 and 1047.0 nm was produced from the Ytterbium doped fiber laser setup by incorporating 10 cm of photonic crystal fiber and finely adjusting the polarization controller. The self-started Q-switch had a pump power of 132.15 mW and a frequency ranging from 3.79 to 15.63 kHz. Therefore, TI:Bi2Te3 was suitable as a potential broadband SA in a 1 micron region

Tunable wavelength generation in the 1 μm region incorporating a 16-channel arrayed waveguide grating (AWG)

A tunable single- and dual-wavelength ytterbium-doped fiber laser, incorporating a 16-channel arrayed waveguide grating is proposed and demonstrated. The side mode suppression ratio from the proposed setup has an average value of 52.97 dB (single-wavelength generation) and 58.19 dB (dual-wavelength generation). The tunable dual wavelength ranged from 1039.98 nm to 1047.48 nm with wavelength spacing ranging from 0.50 nm to 7.5 nm. A stability test from the experiment shows a power variation of 0.8 dB, and a wavelength fluctuation of 0.02 nm indicates the stability and reliability of the proposed work

Using a black phosphorus saturable absorber to generate dual wavelengths in a Q-switched ytterbium-doped fiber laser

Using a few-layer black phosphorus (BP) thin film that acts as a saturable absorber (SA) in an ytterbium-doped fiber laser setup, we experimentally demonstrated a passively dual-wavelength Q-switching laser operation. The setup also incorporated a D-shaped polished fiber as a wavelength selective filter. As the SA was used in the ring cavity, a dual-wavelength Q-switch produced consistent outputs at 1038.68 and 1042.05 nm. A maximum pulse energy of 2.09 nJ with a shortest pulse width of 1.16 μs was measured for the achieved pulses. In addition, the repetition rate increased from 52.52 to 58.73 kHz with the increment of the pump level. Throughout the measurement process, the results were obtained consistently and this demonstrates that the BP film is a very good candidate to produce Q-switching pulses for the 1 micron region