33 research outputs found

    Experimental Study of Subcooled Boiling Heat Transfer of Axial and Swirling Flows inside Mini Annular Gaps

    Get PDF
    An experimental study of the subcooled boiling heat transfer of axial and swirling upward flows inside vertical mini annular gaps was conducted using deionized water. The subcooled boiling heat transfer coefficients and the boiling curves of the flow inside mini annular gaps with different gap sizes have been investigated. The experimental results both for the single phase heat transfer and subcooled boiling heat transfer inside mini annular gaps showed very good agreement with correlations in the literature. The results showed that the subcooled boiling heat transfer coefficient for a given heat flux increases as the size of the annular gap is decreased. The maximum wall superheat is also influenced negligibly by mass flux. Furthermore, the effects of swirl flow by using spring insets inside the mini annuli on the single phase and subcooled boiling heat transfer have been studied. The results showed that the single phase and subcooled boiling heat transfer coefficients are increased by having swirl flow inside mini annuli using spring inserts. The obtained results also showed that the heat transfer enhancement by having swirl flow inside the annuli using spring inserts decreases as the applied heat flux is increased in the subcooled boiling heat transfer region

    Comparing the geodetical and geotechnical methods in investigating the deformation of earthfill dams; A case study of Mahabad Earthfill Dam, Iran

    No full text
    The monitoring of an earthfill dam during the various phases of the construction and service is a crucial process to investigate the performance of the dam from the safety point of view. Monitoring is carried out through installing the instruments at the critical locations. In the present paper, instrumentation data and the numerical analyses have been used for the monitoring of Mahabad earthfill dam, Iran. Numerical analyses were carried out using Plaxis and Sigma-W. Considering the good agreement between the measured data and the values predicted by Plaxis and Sigma-W, it can be concluded that the numerical models developed in the present paper are accurate enough to be used for the analysis of earthfill dams

    Flow structure and particle deposition analyses for optimization of a pressurized metered dose inhaler (pMDI) in a model of tracheobronchial airway.

    No full text
    Inhalation therapy plays an important role in management or treatment of respiratory diseases such asthma and chronic obstructive pulmonary diseases (COPDs). For decades, pressurized metered dose inhalers (pMDIs) have been the most popular and prescribed drug delivery devices for inhalation therapy. The main objectives of the present computational work are to study flow structure inside a pMDI, as well as transport and deposition of micron-sized particles in a model of human tracheobronchial airways and their dependence on inhalation air flow rate and characteristic pMDI parameters. The upper airway geometry, which includes the extrathoracic region, trachea, and bronchial airways up to the fourth generation in some branches, was constructed based on computed tomography (CT) images of an adult healthy female. Computational fluid dynamics (CFD) simulation was employed using the k-ω model with low-Reynolds number (LRN) corrections to accomplish the objectives. The deposition results of the present study were verified with the in vitro deposition data of our previous investigation on pulmonary drug delivery using a hollow replica of the same airway geometry as used for CFD modeling. It was found that the flow structure inside the pMDI and extrathoracic region strongly depends on inhalation flow rate and geometry of the inhaler. In addition, regional aerosol deposition patterns were investigated at four inhalation flow rates between 30 and 120 L/min and for 60 L/min yielding highest deposition fractions of 24.4% and 3.1% for the extrathoracic region (EX) and the trachea, respectively. It was also revealed that particle deposition was larger in the right branches of the bronchial airways (right lung) than the left branches (left lung) for all of the considered cases. Also, optimization of spray characteristics showed that the optimum values for initial spray velocity, spray cone angle and spray duration were 100 m/s, 10∘ and 0.1 sec, respectively. Moreover, spray cone angle, more than any other of the investigated pMDI parameters can change the deposition pattern of inhaled particles in the airway model. In conclusion, the present investigation provides a validated CFD model for particle deposition and new insights into the relevance of flow structure for deposition of pMDI-emitted pharmaceutical aerosols in the upper respiratory tract
    corecore