55 research outputs found
Radio Frequency Magnetron Sputter Deposition as a Tool for Surface Modification of Medical Implants
The resent advances in radio frequency (RF)‐magnetron sputtering of hydroxyapatite films are reviewed and challenges posed. The principles underlying RF‐magnetron sputtering used to prepare calcium phosphate‐based, mainly hydroxyapatite coatings, are discussed in this chapter. The fundamental characteristic of the RF‐magnetron sputtering is an energy input into the growing film. In order to tailor the film properties, one has to adjust the energy input into the substrate depending on the desired film properties. The effect of different deposition control parameters, such as deposition time, substrate temperature, and substrate biasing on the hydroxyapatite (HA) film properties is discussed
Corrosion and tribological performance of quasi-stoichiometric titanium containing carbo-nitride coatings
Zr, Nb and Si doped TiCN coatings, with (C+N)/(metal + Si) ratios of approximately 1, were deposited on stainless steel and Si wafer substrates using a cathodic arc technique in a mixture of N2 and CH4 gases. The coatings were comparatively analysed for elemental and phase composition, adhesion, anticorrosive properties and tribological performance at ambient and 250 °C. Zr, Nb and Si alloying contents in the coatings were in the range 2.9–9.6 at.%. All the coatings exhibited f.c.c. solid solution structures and had a 〈111〉 preferred orientation. In the adhesion tests conducted, critical loads ranged from 20 to 30 N, indicative of a good adhesion to substrate materials. The Ti based coatings with Nb or Si alloying elements proved to be resistant to corrosive attack in 3.5% NaCl and of these coatings the TiNbCN was found to have the best corrosion resistance. TiCN exhibited the best tribological performance at 250 °C, while at ambient temperatures it was TiNbCN. Abrasive and oxidative wear was found to be the main wear mechanism for all of the coatings. Of the tested coatings, TiNbCN coatings would be the most suitable candidate for severe service (high temperature, corrosive, etc.) applications
Biodegradable ceramics consisting of hydroxyapatite for orthopaedic implants
This study aims to analyze hydroxyapatite (HAP) coatings enriched with Mg and Ti
prepared by a magnetron sputtering technique on Ti6Al4V substrate. For preparation of the coatings,
three magnetron targets (HAP, MgO and TiO2) were simultaneously co-worked. The concentration
of Mg added was varied by modifying the power applied to the MgO target. In all coatings, the Ti
concentration was maintained constant by keeping the same cathode power fed during the whole
deposition. The influence of different Mg dopant contents on the formation of phase, microstructure
and morphology of the obtained Ti-doped HAP coatings were characterized by Fourier transform
infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). Moreover, the effects of Mg
addition upon corrosion, mechanical and biological properties were also investigated. Mg- and
Ti-doped HAP coating obtained at low radio-frequency (RF) power fed to the MgO target provided
material with high corrosion resistance compared to other coatings and bare alloy. A slight decrease
in hardness of the coatings was found after the Mg addition, from 8.8 to 5.7 GPa. Also, the values
of elastic modulus were decreased from 87 to 53 GPa, this being an advantage for biomedical
applications. The coatings with low Mg concentration proved to have good deformation to yielding
and higher plastic properties. Biological test results showed that the novel surfaces exhibited excellent
properties for the adhesion and growth of bone cells. Moreover, early adherent vital cell numbers were
significantly higher on both coatings compared to Ti6Al4V, suggesting that Mg ions may accelerate
initial osteoblast adhesion and proliferation
Pectin coatings on titanium alloy scaffolds produced by additive manufacturing:Promotion of human bone marrow stromal cell proliferation
Ti6Al4V is a popular biomaterial for load-bearing implants for bone contact, which can be fabricated by additive manufacturing technologies. Their long-term success depends on their stable anchoring in surrounding bone, which in turn depends on formation of new bone tissue on the implant surface, for which adhesion and proliferation of bone-forming cells is a pre-requisite. Hence, surface coatings which promote cell adhesion and proliferation are desirable. Here, Ti6Al4V discs prepared by additive manufacturing (EBM) were coated with layers of pectins, calcium-binding polysaccharides derived from citrus (C) and apple (A), which also contained alkaline phosphatase (ALP), the enzyme responsible for mineralization of bone tissue. Adhesion and proliferation of human bone marrow stromal cells (hBMSC) were assessed. Proliferation after 7 days was increased by A-ALP coatings and, in particular, by C-ALP coatings. Cell morphology was similar on coated and uncoated samples. In conclusion, ALP-loaded pectin coatings promote hBMSC adhesion and proliferation
Physician migration at its roots: a study on the emigration preferences and plans among medical students in Romania
Effect of calcination time on the physicochemical properties and photocatalytic performance of carbon and nitrogen co-doped TiO2 nanoparticles
The application of highly active nano catalysts in advanced oxidation processes (AOPs)
improves the production of non-selective hydroxyl radicals and co-oxidants for complete remediation
of polluted water. This study focused on the synthesis and characterisation of a highly active visible
light C–N-co-doped TiO2 nano catalyst that we prepared via the sol-gel method and pyrolysed at
350 ◦C for 105 min in an inert atmosphere to prevent combustion of carbon moietie
Synthesis, Characterisation, Photocatalytic Activity, and Aquatic Toxicity Evaluation of TiO2 Nanoparticles
Imidacloprid (IMD) is a toxic pesticide, and is one of the eight most widely used pesticides globally. Heterogeneous photocatalysis has often been investigated in recent years and can be successfully applied to remove imidacloprid from water. However, less investigated is the toxic effect of both the photocatalyst and the pesticide on aquatic life. Titanium dioxide (TiO2) remains the most effective photocatalyst, provided it is not toxic to the aquatic environment. This study investigated the TiO2 synthesis, characterisation, and photocatalytic activity on imidacloprid degradation and the toxicity of TiO2 nanoparticles and imidacloprid on the green algae Chlorella vulgaris. In the photodegradation process of IMD (initial concentration of 20 mg/L), electrons play an essential role; the degradation efficiency of IMD after 6 h increased from 69 to 90% under UV irradiation when holes (h+) scavengers were added, which allowed the electrons to react with the pollutant, resulting in lowering the recombination rate of electron-hole charge carriers. Growth inhibition of Chlorella vulgaris and effective concentration (EC50) were determined to study the toxic effect of TiO2 nanoparticles and imidacloprid. The EC50 increased from 289.338 mg/L in the first 24 h to 1126.75 mg/L after 96 h Chlorella vulgaris algal age, when the toxicant was TiO2. When IMD was the aquatic toxicant, a decrease in EC50 was observed from 22.8 mg/L (24 h) to 0.00777 mg/L (120 h), suggesting a long-term high toxicity level when pesticides in low concentrations are present in an aquatic environment
Solid solution or amorphous phase formation in TiZr-based ternary to quinternary multi-principal-element films
TiZr-based multicomponent metallic films composed of 3–5 constituents with almost equal atomic concentrations were prepared by co-sputtering of pure metallic targets in an Ar atmosphere. X-ray diffraction was employed to determine phase composition, crystalline structure, lattice parameters, texture and crystallite size of the deposited films.
The deposited films exhibited only solid solution (fcc, bcc or hcp) or amorphous phases, no intermetallic components being detected. It was found that the hcp structure was stabilized by the presence of Hf or Y, bcc by Nb or Al and fcc by Cu. For the investigated films, the atomic size difference, mixing enthalpy, mixing entropy, Gibbs free energy of mixing and the electronegativity difference for solid solution and amorphous phases were calculated based on Miedema׳s approach of the regular solution model. It was shown that the atomic size difference and the ratio between the Gibbs free energies of mixing of the solid solution and amorphous phases were the most significant parameters controlling the film crystallinity
- …