Shrinkage strain – Rates study of dental composites based on (BisGMA/TEGDMA) monomers

AbstractThe viscosity of the initial monomer mixture and the chemical structure of the monomers are both important variables in the kinetic behavior of resin composites. This paper aims to determine the effect of opaque mineral fillers and monomer ratios on the shrinkage strain-rate and time at maximum shrinkage strain (Smax) rate, of experimental composites based on (BisGMA/TEGDMA) monomers. Polymerization shrinkage and the degree of conversion (DC) of resin composites are closely related manifestations of the same process. The proportionality of these two properties was also investigated by studying the variation of the ratio: (total shrinkage strain/degree of conversion): (Smax/DC), as a function of mineral filler contents and monomer ratios.Resin composites were prepared by mixing different monomer ratios of (BisGMA/TEGDMA) with camphoroquinone and dimethyl aminoethyl methacrylate (DMAEMA) as photo-initiator system. Five different radiopacifying filler agents: La2O3, BaO, BaSO4,·SrO and ZrO2 at various volume fractions ranging from 0 to 80wt.% were added. The samples were cured at ca. 550mW/cm2. The shrinkage strain-rate, was calculated from the derivative of shrinkage strain using numerical differentiation. The shrinkage strain was measured by the bonded-disk technique at room temperature. Degree of conversion was calculated using FTIR/ATR spectroscopy.The results revealed that the fraction of opaque filler had no significant effect on the shrinkage strain-rate and on the time at maximum shrinkage strain-rate but these two parameters are closely related to the monomer ratios and viscosity of the organic matrix. The results have confirmed the proportionality of the shrinkage strain and DC and showed that the filler contents and monomer ratios would not affect this proportionality

The Conjoined Microprocessor

Over the last twenty years, the research community has devised sophisticated methods for retrieving secret information from sidechannel emanations, and for resisting such attacks. This paper introduces a new CPU architecture called the Conjoined Microprocessor. The Conjoined Microprocessor can randomly interleave the execution of two programs at very low extra hardware cost. We developed for the Conjoined Microprocessor a preprocessor tool that turns a target algorithm into two (or more) separate queues like $Q_0$ and $Q_1$ that can run in alternation. $Q_0$ and $Q_1$ fulfill the same operation as the original target algorithm. Power-analysis resistance is achieved by randomly alternating the execution of $Q_0$ and $Q_1$, with different runs resulting in different interleavings. Experiments reveal that this architecture is indeed effective against CPA

Comparison and Implementation of a Rigid and a Flexible Multibody Planetary Gearbox Model

We propose algorithms for developing (1) a rigid (constrained) and (2) a flexible planetary gearbox model. The two methods are compared against each other and advantages/disadvantages of each method are discussed. The rigid model (1) has gear tooth reaction forces expressed by Lagrange multipliers. The flexible approach (2) is being compared with the gear tooth forces from the rigid approach, first without damping and second the influence of damping is examined. Variable stiffness as a function of base circle arc length is implemented in the flexible approach such that it handles the realistic switch between one and two gear teeth in mesh. The final results are from modelling the planetary gearbox in a 500 kW wind turbine which we also described in Jørgensen et.al (2013)

Finite Element Analysis of Bone and Experimental Validation

This chapter describes the application of the finite element (FE) method to bone tissues. The aspects that differ the most between bone and other materials’ FE analysis are the type of elements used, constitutive models, and experimental validation. These aspects are looked at from a historical evolution stand point. Several types of elements can be used to simulate similar bone structures and within the same analysis many types of elements may be needed to realistically simulate an anatomical part. Special attention is made to constitutive models, including the use of density-elasticity relationships made possible through CT-scanned images. Other more complex models are also described that include viscoelasticity and anisotropy. The importance of experimental validation is discussed, describing several methods used by different authors in this challenging field. The use of cadaveric human bones is not always possible or desirable and other options are described, as the use of animal or artificial bones. Strain and strain rate measuring methods are also discussed, such as rosette strain gauges and optical devices.publishe

Leptin Administration Favors Muscle Mass Accretion by Decreasing FoxO3a and Increasing PGC-1α in ob/ob Mice

Absence of leptin has been associated with reduced skeletal muscle mass in leptin-deficient ob/ob mice. The aim of our study was to examine the effect of leptin on the catabolic and anabolic pathways regulating muscle mass. Gastrocnemius, extensor digitorum longus and soleus muscle mass as well as fiber size were significantly lower in ob/ob mice compared to wild type littermates, being significantly increased by leptin administration (P<0.001). This effect was associated with an inactivation of the muscle atrophy-related transcription factor forkhead box class O3 (FoxO3a) (P<0.05), and with a decrease in the protein expression levels of the E3 ubiquitin-ligases muscle atrophy F-box (MAFbx) (P<0.05) and muscle RING finger 1 (MuRF1) (P<0.05). Moreover, leptin increased (P<0.01) protein expression levels of peroxisome proliferator-activated receptor γ coactivator-1α (PGC-1α), a regulator of muscle fiber type, and decreased (P<0.05) myostatin protein, a negative regulator of muscle growth. Leptin administration also activated (P<0.01) the regulators of cell cycle progression proliferating cell nuclear antigen (PCNA) and cyclin D1, and increased (P<0.01) myofibrillar protein troponin T. The present study provides evidence that leptin treatment may increase muscle mass of ob/ob mice by inhibiting myofibrillar protein degradation as well as enhancing muscle cell proliferation

On the constraints violation in forward dynamics of multibody systems

It is known that the dynamic equations of motion for constrained mechanical multibody systems are frequently formulated using the Newton-Euler’s approach, which is augmented with the acceleration constraint equations. This formulation results in the establishment of a mixed set of partial differential and algebraic equations, which are solved in order to predict the dynamic behavior of general multibody systems. The classical resolution of the equations of motion is highly prone to constraints violation because the position and velocity constraint equations are not fulfilled. In this work, a general and comprehensive methodology to eliminate the constraints violation at the position and velocity levels is offered. The basic idea of the described approach is to add corrective terms to the position and velocity vectors with the intent to satisfy the corresponding kinematic constraint equations. These corrective terms are evaluated as function of the Moore-Penrose generalized inverse of the Jacobian matrix and of the kinematic constraint equations. The described methodology is embedded in the standard method to solve the equations of motion based on the technique of Lagrange multipliers. Finally, the effectiveness of the described methodology is demonstrated through the dynamic modeling and simulation of different planar and spatial multibody systems. The outcomes in terms of constraints violation at the position and velocity levels, conservation of the total energy and computational efficiency are analyzed and compared with those obtained with the standard Lagrange multipliers method, the Baumgarte stabilization method, the augmented Lagrangian formulation, the index-1 augmented Lagrangian and the coordinate partitioning method.The first author expresses his gratitude to the Portuguese Foundation for Science and Technology through the PhD grant (PD/BD/114154/2016). This work has been supported by the Portuguese Foundation for Science and Technology with the reference project UID/EEA/04436/2013, by FEDER funds through the COMPETE 2020 – Programa Operacional Competitividade e Internacionalização (POCI) with the reference project POCI-01-0145-FEDER-006941.info:eu-repo/semantics/publishedVersio

An automated coding and classification system with supporting database for effective design of manufacturing systems

The philosophy of group technology (GT) is an important concept in the design of flexible manufacturing systems and manufacturing cells. Group technology is a manufacturing philosophy that identifies similar parts and groups them into families. Beside assigning unique codes to these parts, group technology developers intend to take advantage of part similarities during design and manufacturing processes. GT is not the answer to all manufacturing problems, but it is a good management technique with which to standardize efforts and eliminate duplication. Group technology classifies parts by assigning them to different families based on their similarities in: (1) design attributes (physical shape and size), and/or (2) manufacturing attributes (processing sequence). The manufacturing industry today is process focused; departments and sub units are no longer independent but are interdependent. If the product development process is to be optimized, engineering and manufacturing cannot remain independent any more: they must be coordinated. Each sub-system is a critical component within an integrated manufacturing framework. The coding and classification system is the basis of CAPP and the functioning and reliability of CAPP depends on the robustness of the coding system. The proposed coding system is considered superior to the previously proposed coding systems, in that it has the capability to migrate into multiple manufacturing environments. This article presents the design of a coding and classification system and the supporting database for manufacturing processes based on both design and manufacturing attributes of parts. An interface with the spreadsheet will calculate the machine operation costs for various processes. This menu-driven interactive package is implemented using dBASE-IV. Part Family formation is achieved using a KAMCELL package developed in TURBO Pascal.Peer Reviewedhttp://deepblue.lib.umich.edu/bitstream/2027.42/46606/1/10845_2004_Article_BF00123696.pd