8 research outputs found
Performance of peat biofilters treating ethyl acetate and toluene mixtures under non-steady-state conditions
[Abstract] This paper presents the response of peat biofilters to loading changes corresponding to industrial practices such as overnight and weekend shutdowns, intermittent emission or inlet concentration peaks. Three laboratory-scale reactors fed with air contaminated with ethyl acetate, toluene or a 1:1 mixture of ethyl acetate and toluene were operated under 65 g m-3 h-1 inlet load and 60 s EBRT during 16 h/day, 5 days/week. Dynamic behavior after feed resumption after night and weekend closures showed a 1-2 h period of transient response to recover stable CO2 production values. No increase in VOC emission was observed, except for biofilters treating toluene for which a transient peak in VOC emission during 4-8 h after weekend closures was detected. More stressful conditions such as intermittent emissions (2 h-on/ 2 h-off, 16 h/day, 5 days/week), or inlet concentration peaks (40-min, 50% increase) were successfully handled in the biofilter treating only ethyl acetate; but deterioration in the operation was observed in presence of toluene. The system performance after 15-days starvation period was fully recovered in less than 8 h of re-acclimation period. Living and dead cells monitoring results are also presented
Biodegradation of ethyl acetate and toluene mixtures by a peat biofilter: respirometry monitoring and dynamics of living and dead bacterial cells
Removal of a mixture of oxygenated VOCs in a biotrickling filter
[Abstract] Laboratory scale-studies on the biodegradation of a 1:1:1 wt mixture of three oxygenated volatile organic compounds (VOCs), ethanol, ethyl acetate and methyl-ethyl ketone (MEK) in a biotrickling filter were carried out using two identically sized columns, filled with different polypropylene rings. The reactors were seeded with a two-month preconditioned culture from activated sludge. The performance of the biotrickling filters was examined for a continuous period of 4 months at VOC concentration from 125 mg-C/m3 to 550 mg-C/m3 and at gas flow rates of around 1.0 m3/h, 2.0 m3/h and 4.6 m3/h, which correspond to gas empty bed residence times (EBRT) of 68 s, 33 s and 16 s, respectively. Similar performance was obtained for both supports. Intermittent flow rate of trickling liquid was shown as beneficial to improve the removal efficiency of the system. A stratification in the substrate consumption was observed from gas composition profiles, with MEK % in the emission greater than 78%. Continuous VOC feeding resulted in an excessive accumulation of biomass and high pressure drop was developed in less than 20-30 days of operation. Intermittent VOC loading with night and weekend feed cut-off periods passing dried air, but without water addition, was shown as a successful operational mode to control the biofilm thickness. In this case, operation at high inlet loads was extended for more than 50 days maintaining high removal efficiencies and low pressure drops
Abatement of styrene waste gas emission by biofilter and biotrickling filter: comparison of packing materials and inoculation procedures
The removal of styrene was studied using 2 biofilters packed with peat and coconut fibre (BF1-P and BF2-C, respectively) and 1 biotrickling filter (BTF) packed with plastic rings. Two inoculation procedures were applied: an enriched culture with strain Pseudomonas putida CECT 324 for biofilters and activated sludge from a municipal wastewater treatment plant for the BTF. Inlet loads (ILs) between 10 and 45 g m-3 h-1 and empty bed residence times (EBRTs) from 30 to 120 s were applied. At inlet concentrations ranging between 200 and 400 mg Nm-3, removal efficiencies between 70 and 95% were obtained in the 3 bioreactors. Maximum elimination capacities (ECs) of 81 and 39 g m-3 h-1 were obtained for the first quarter of the BF1-P and BF2-C, respectively (IL of 173 g m-3 h-1 and EBRT of 60 s in BF1-P; IL of 89 g m-3 h-1 and EBRT of 90 s in BF2-C). A maximum EC of 52 g m-3 h-1 was obtained for the first third of the BTF (IL of 116 g m-3 h-1, EBRT of 45 s). Problems regarding high pressure drop appeared in the peat biofilter, whereas drying episodes occurred in the coconut fibre biofilter. DGGE revealed that the pure culture used for biofilter inoculation was not detected by day 105. Although 2 different inoculation procedures were applied, similar styrene removal at the end of the experiments was observed. The use as inoculum of activated sludge from municipal wastewater treatment plant appears a more feasible option