395 research outputs found
No-vent fill pressurization tests using a cryogen simulant
The results are described of an experimental program which studied the performance of various no-vent fill techniques for tank-to-tank liquid transfer. The tests were performed using a cryogen simulant (Freon-114) and a test bed consisting of a multiple tank/plumbing network that enabled studies of a variety of different inlet flow and active mixing regimes. Several results and conclusions were drawn from the 26 transfer experiments comprising the program. Most notable was the significant improvement in fill performance (i.e., minimized fill time and maximized fill fraction) with increased agitation of the liquid surface. Another was the close correlation between measured condensation rates and those predicted by recent theories which express condensation as a function of turbulent eddy effects on the liquid surface. In most cases, test data exhibited strong agreement with an analytical model which accounts for tank heat transfer and thermodynamics in a 1 g environment
Multipurpose electric furnace system
A multipurpose electric furnace system of advanced design for space applications was developed and tested. This system is intended for use in the Apollo-Soyuz Test Program. It consists of the furnace, control package and a helium package for rapid cooldown
Design and analysis report for the RL10-2B breadboard low thrust engine
The breadboard low thrust RL10-2B engine is described. A summary of the analysis and design effort to define the multimode thrust concept applicable to the requirements for the upper stage vehicles is provided. Baseline requirements were established for operation of the RL10-2B engine under the following conditions: (1) tank head idle at low propellant tank pressures without vehicle propellant conditioning or settling thrust; (2) pumped idle at a ten percent thrust level for low G deployment and/or vehicle tank pressurization; and (3) full thrust (15,000 lb.). Several variations of the engine configuration were investigated and results of the analyses are included
High pressure pre-treatments promote higher rate and degree of enzymatic hydrolysis of cellulose
The effect of high pressure (HP) pre-treatments on the subsequent enzymatic hydrolysis of cellulose from bleached kraft Eucalyptus globulus pulp by cellulase from Tricoderma viride was evaluated. Pressure pre-treatments of 300 and 400 MPa during 5–45 min, lead to both an increased rate and degree of hydrolysis, reaching values ranging from 1.5- to 1.9-fold, quantified by the formation of reducing sugars. Both the pressure and time under pressure influenced the enzymatic hydrosability of the cellulosic pulps, with the former being more important. The results indicate that the pressure pre-treatments promoted an increased accessibility of cellulose towards cellulase in the cell wall. The results obtained open promising possibilities, to contribute to overcome conventional limitations of enzymatic cellulose hydrolysis for the production of fermentable glucose, for the production of second generation bioethanol and chemicals by enhancement of both rate and yield of hydrolysis. The results are also of interest for the preparation of “pressure engineered” celullose with incremented tailored hydrolysis patterns
Recommended from our members
New Pellet Injection Schemes on DIII-D
The pellet fueling system on DIII-D has been modified for injection of deuterium pellets from two vertical ports and two inner wall locations on the magnetic high-field side (HFS) of the tokamak. The HFS pellet injection technique was first employed on ASDEX-Upgrade with significant improvements reported in both pellet penetration and fueling efficiency. The new pellet injection schemes on DIII-D required the installation of new guide tubes. These lines are {approx_equal}12.5 m in total length and are made up of complex bends and turns (''roller coaster'' like) to route pellets from the injector to the plasma, including sections inside the torus. The pellet speed at which intact pellets can survive through the curved guide tubes is limited ({approx_equal}200-300 m/s for HFS injection schemes). Thus, one of the three gas guns on the injector was modified to provide pellets in a lower speed regime than the original guns (normal speed range {approx_equal}500 to 1000 m/s). The guide tube installations and gun modifications are described along with the injector operating parameters, and the latest test results are highlighted
Micro-Hall Magnetometry Studies of Thermally Assisted and Pure Quantum Tunneling in Single Molecule Magnet Mn12-Acetate
We have studied the crossover between thermally assisted and pure quantum
tunneling in single crystals of high spin (S=10) uniaxial single molecule
magnet Mn12-acetate using micro-Hall effect magnetometry. Magnetic hysteresis
experiments have been used toinvestigate the energy levels that determine the
magnetization reversal as a function of magnetic field and temperature. These
experiments demonstrate that the crossover occurs in a narrow (~0.1 K) or broad
(~1 K) temperature interval depending on the magnitude and direction of the
applied field. For low external fields applied parallel to the easy axis, the
energy levels that dominate the tunneling shift abruptly with temperature. In
the presence of a transverse field and/or large longitudinal field these energy
levels change with temperature more gradually. A comparison of our experimental
results with model calculations of this crossover suggest that there are
additional mechanisms that enhance the tunneling rate of low lying energy
levels and broaden the crossover for small transverse fields.Comment: 5 pages, 5 figure
Recommended from our members
A two-stage pneumatic repeating pellet injector for refueling magnetically confined plasmas in long-pulse fusion experiments
An experiment to demonstrate the feasibility of a repetitive pneumatic pellet injector at 1 Hz in the velocity range of 2 to 3 knVs was carried out in a collaboration between Oak Ridge National Laboratory and ENEA Frascati, in the context of a cooperative agreement between the US Department of Energy and EURATOM-ENEA Association. The third round of this experiment was completed in May 1995. Both the operation and performance of the equipment were improved, and the original objectives of the collaboration have been met. The facility was also briefly operated with neon pellets to explore the potential for producing fast ``killer`` pellets for disruption amelioration applications. Speeds of 1.7 km/s were achieved using a piston mass of 43 g. Higher speeds should be achievable with a system specifically designed for neon or other higher Z gases. Finally, tests were performed with thin boron carbide coatings (2 {mu}m) on the Ergal pistons. The test results were encouraging because piston friction was reduced was the piston wear
- …