Meeting Review: Airborne Aerosol Inlet Workshop

Proceedings from the Airborne Aerosol Inlet Workshop are presented. The two central topics of discussion were the role of aerosols in atmospheric processes and the difficulties in characterizing aerosols. The following topics were discussed during the working sessions: airborne observations to date; identification of inlet design issues; inlet modeling needs and directions; objectives for aircraft experiments; and future laboratory and wind tunnel studies

High-Speed Low-Voltage Line Driver for SerDes Applications

The driving factor behind this research was to design & develop a line driver capable of meeting the demanding specifications of the next generation of SerDes devices. In this thesis various line driver topologies were analysed to identify a topology suited for a high-speed low-voltage operating environment. This thesis starts of by introducing a relatively new high-speed communication Device called SerDes. SerDes is used in wired chip-to-chip communications and operates by converting a parallel data stream in a serial data stream that can be then transmitted at a higher bit rate, existing SerDes devices operate up to 12.5Gbps. A matching SerDes device at the destination will then convert the serial data stream back into a parallel data stream to be read by the destination ASIC. SerDes typically uses a line driver with a differential output. Using a differential line driver increases the resilience to outside sources of noise and reduces the amount of EM radiation produced by transmission. The focus of this research is to design and develop a line driver that can operate at 40Gbps and can function with a power supply of less than IV. This demanding specification was decided to be an accurate representation of future requirements that a line driver in a SerDes device will have to conform to. A suitable line driver with a differential output was identified to meet the demanding specifications and was modified so that it can perfonn an equalisation technique called pre-distortion. Two variations of the new topology were outlined and a behavioural model was created for both using Matlab Simulink. The behavioural model for both variants proved the concept, however only one variant maintained its perfomance once the designs were implemented at transistor level in Cadence, using a 65nm CMOS technology provided by Texas Instruments. The final line driver design was then converted into a layout design, again using Cadence, and RC parasitics were extracted to perfom a post-layout simulation. The post layout simulation shows that the novel line driver can operate at 40Gbps with a power supply of 1 V - O.8V and has a power consumption of 4.54m W /Gbps. The Deterministic Jitter added by the line driver is 12.9ps

Volume 74- Issue 4- January 1963

The Rose Thorn, Rose-Hulman\u27s independent student newspaper.https://scholar.rose-hulman.edu/rosethorn/2055/thumbnail.jp

Mirror - Vol. 13, No. 16 - March 02, 1989

The Mirror (sometimes called the Fairfield Mirror) is the official student newspaper of Fairfield University, and is published weekly during the academic year (September - May). It runs from 1977 - the present; current issues are available online.https://digitalcommons.fairfield.edu/archives-mirror/1281/thumbnail.jp

Chemical spray pyrolysis of Tl-Ba-Ca-Cu-O high-T(sub c) superconductors for high-field bitter magnets

The deposition of Tl-Ba-Ca-Cu-O thick films by spray pyrolyzing a Ba-Ca-Cu-O precursor film and diffusing thallium into the film to form the superconducting phase is examined. This approach was taken to reduce exposure to thallium and its health and safety hazards. The Tl-Ba-Ca-Cu-O system was selected because it has very attractive features which make it appealing to device and manufacturing engineering. Tl-Ba-Ca-Cu-O will accommodate a number of superconducting phases. This attribute makes it very forgiving to stoichiometric fluctuations in the bulk and film. It has excellent thermal and chemical stability, and appears to be relatively insensitive to chemical impurities. Oxygen is tightly bound into the systems, consequently there is no orthorhombic (conductor) to tetragonal (insulator) transition which would affect a component's lifetime. More significantly, the thallium based superconductors appear to have harder magnetic properties than the other high-Tc oxide ceramics. Estimates using magnetoresistance measurements indicate that at 77 K Tl2Ba2CaCu2O10 will have an upper critical field, H(sub c2) fo 26 Tesla for applied fields parallel to the c-axis and approximately 1000 Tesla for fields oriented in the a-b plane. Results to date have shown that superconducting films can be reproducibly deposited on 100 oriented MgO substrates. One film had a zero resistance temperature of 111.5 K. Furthermore, x ray diffraction analysis of the films showed preferential c-axis orientation parallel to the plane of the substrate. These results have now made it possible to consider the manufacture of a superconducting tape wire which can be configured into a topology useful for high-field magnet designs. The research which leads to the preparation of these films and plans for further development are reviewed

NASA Tech Briefs, October 2000

Topics include: special coverage sections on CAD, CAE, and PDM, and, Composites and Plastics, and sections on electronic components and systems, software, test and measurement, mechanics, manufacturing/fabrication, physical sciences, information sciences, book and reports, and special sections of Electronics Tech Briefs and Motion Control Tech Brief

Complete 2020 Program

Program and schedule of events for the 31st Annual John Wesley Powell Student Research Conference

Utilization of lunar materials and expertise for large scale operations in space: Abstracts

The practicality of exploiting the moon, not only as a source of materials for large habitable structures at Lagrangian points, but also as a base for colonization is discussed in abstracts of papers presented at a special session on lunar utilization. Questions and answers which followed each presentation are included after the appropriate abstract. Author and subject indexes are provided