Variability-driven module selection with joint design time optimization and post-silicon tuning

Abstract—Increasing delay and power variation are significant chal-lenges to the designers as technology scales to the deep sub-micron (DSM) regime. Traditional module selection techniques in high level synthesis use worst case delay/power information to perform the optimization, and therefore may be too pessimistic such that extra resources are used to guarantee design requirements. Parametric yield, which is defined as the probability of the synthesized hardware meeting the performance/power constraints, can be used to guide design space exploration. The para-metric yield can be effectively improved by combining both design-time variation-aware optimization and post silicon tuning techniques (such as adaptive body biasing (ABB)). In this paper, we propose a module selection algorithm that combines design-time optimization with post-silicon tuning (using ABB) to maximize design yield. A variation-aware module selection algorithm based on efficient performance and power yield gradient computation is developed. The post silicon optimization is formulated as an efficient sequential conic program to determine the optimal body bias distribution, which in turn affects design-time module selection. The experiment results show that significant yield can be achieved compared to traditional worst-case driven module selection technique. To the best of our knowledge, this is the first variability-driven high level synthesis technique that considers post-silicon tuning during design time optimization. 1 I

inSense: A Variation and Fault Tolerant Architecture for Nanoscale Devices

Transistor technology scaling has been the driving force in improving the size, speed, and power consumption of digital systems. As devices approach atomic size, however, their reliability and performance are increasingly compromised due to reduced noise margins, difficulties in fabrication, and emergent nano-scale phenomena. Scaled CMOS devices, in particular, suffer from process variations such as random dopant fluctuation (RDF) and line edge roughness (LER), transistor degradation mechanisms such as negative-bias temperature instability (NBTI) and hot-carrier injection (HCI), and increased sensitivity to single event upsets (SEUs). Consequently, future devices may exhibit reduced performance, diminished lifetimes, and poor reliability. This research proposes a variation and fault tolerant architecture, the inSense architecture, as a circuit-level solution to the problems induced by the aforementioned phenomena. The inSense architecture entails augmenting circuits with introspective and sensory capabilities which are able to dynamically detect and compensate for process variations, transistor degradation, and soft errors. This approach creates ``smart\u27\u27 circuits able to function despite the use of unreliable devices and is applicable to current CMOS technology as well as next-generation devices using new materials and structures. Furthermore, this work presents an automated prototype implementation of the inSense architecture targeted to CMOS devices and is evaluated via implementation in ISCAS \u2785 benchmark circuits. The automated prototype implementation is functionally verified and characterized: it is found that error detection capability (with error windows from $\approx$30-400ps) can be added for less than 2\% area overhead for circuits of non-trivial complexity. Single event transient (SET) detection capability (configurable with target set-points) is found to be functional, although it generally tracks the standard DMR implementation with respect to overheads

On Energy Efficient Computing Platforms

In accordance with the Moore's law, the increasing number of on-chip integrated transistors has enabled modern computing platforms with not only higher processing power but also more affordable prices. As a result, these platforms, including portable devices, work stations and data centres, are becoming an inevitable part of the human society. However, with the demand for portability and raising cost of power, energy efficiency has emerged to be a major concern for modern computing platforms. As the complexity of on-chip systems increases, Network-on-Chip (NoC) has been proved as an efficient communication architecture which can further improve system performances and scalability while reducing the design cost. Therefore, in this thesis, we study and propose energy optimization approaches based on NoC architecture, with special focuses on the following aspects. As the architectural trend of future computing platforms, 3D systems have many bene ts including higher integration density, smaller footprint, heterogeneous integration, etc. Moreover, 3D technology can signi cantly improve the network communication and effectively avoid long wirings, and therefore, provide higher system performance and energy efficiency. With the dynamic nature of on-chip communication in large scale NoC based systems, run-time system optimization is of crucial importance in order to achieve higher system reliability and essentially energy efficiency. In this thesis, we propose an agent based system design approach where agents are on-chip components which monitor and control system parameters such as supply voltage, operating frequency, etc. With this approach, we have analysed the implementation alternatives for dynamic voltage and frequency scaling and power gating techniques at different granularity, which reduce both dynamic and leakage energy consumption. Topologies, being one of the key factors for NoCs, are also explored for energy saving purpose. A Honeycomb NoC architecture is proposed in this thesis with turn-model based deadlock-free routing algorithms. Our analysis and simulation based evaluation show that Honeycomb NoCs outperform their Mesh based counterparts in terms of network cost, system performance as well as energy efficiency.Siirretty Doriast

Monitor amb control strategies to reduce the impact of process variations in digital circuits

As CMOS technology scales down, Process, Voltage, Temperature and Ageing (PVTA) variations have an increasing impact on the performance and power consumption of electronic devices. These issues may hold back the continuous improvement of these devices in the near future. There are several ways to face the variability problem: to increase the operating margins of maximum clock frequency, the implementation of lithographic friendly layout styles, and the last one and the focus of this thesis, to adapt the circuit to its actual manufacturing and environment conditions by tuning some of the adjustable parameters once the circuit has been manufactured. The main challenge of this thesis is to develop a low-area variability compensation mechanism to automatically mitigate PVTA variations in run-time, i.e. while integrated circuit is running. This implies the development of a sensor to obtain the most accurate picture of variability, and the implementation of a control block to knob some of the electrical parameters of the circuit.A mesura que la tecnologia CMOS escala, les variacions de Procés, Voltatge, Temperatura i Envelliment (PVTA) tenen un impacte creixent en el rendiment i el consum de potència dels dispositius electrònics. Aquesta problemàtica podria arribar a frenar la millora contínua d'aquests dispositius en un futur proper. Hi ha diverses maneres d'afrontar el problema de la variabilitat: relaxar el marge de la freqüència màxima d'operació, implementar dissenys físics de xips més fàcils de litografiar, i per últim i com a tema principal d'aquesta tesi, adaptar el xip a les condicions de fabricació i d'entorn mitjançant la modificació d'algun dels seus paràmetres ajustables una vegada el circuit ja ha estat fabricat. El principal repte d'aquesta tesi és desenvolupar un mecanisme de compensació de variabilitat per tal de mitigar les variacions PVTA de manera automàtica en temps d'execució, és a dir, mentre el xip està funcionant. Això implica el desenvolupament d'un sensor capaç de mesurar la variabilitat de la manera més acurada possible, i la implementació d'un bloc de control que permeti l'ajust d'alguns dels paràmetres elèctrics dels circuits

Role of wide bandgap materials in power electronics for smart grids applications

At present, the energy transition is leading to the replacement of large thermal power plants by distributed renewable generation and the introduction of different assets. Consequently, a massive deployment of power electronics is expected. A particular case will be the devices destined for urban environments and smart grids. Indeed, such applications have some features that make wide bandgap (WBG) materials particularly relevant. This paper analyzes the most important features expected by future smart applications from which the characteristics that their power semiconductors must perform can be deduced. Following, not only the characteristics and theoretical limits of wide bandgap materials already available on the market (SiC and GaN) have been analyzed, but also those currently being researched as promising future alternatives (Ga2O3, AlN, etc.). Finally, wide bandgap materials are compared under the needs determined by the smart applications, determining the best suited to them. We conclude that, although SiC and GaN are currently the only WBG materials available on the semiconductor portfolio, they may be displaced by others such as Ga2O3 in the near futur