45 research outputs found
Systematic Comparison of HF CMOS Transconductors
Transconductors are commonly used as active elements in high-frequency (HF) filters, amplifiers, mixers, and oscillators. This paper reviews transconductor design by focusing on the V-I kernel that determines the key transconductor properties. Based on bandwidth considerations, simple V-I kernels with few or no internal nodes are preferred. In a systematic way, virtually all simple kernels published in literature are generated. This is done in two steps: 1) basic 3-terminal transconductors are covered and 2) then five different techniques to combine two of them in a composite V-I kernel. In order to compare transconductors in a fair way, a normalized signal-to-noise ratio (NSNR) is defined. The basic V-I kernels and the five classes of composite V-I kernels are then compared, leading to insight in the key mechanisms that affect NSNR. Symbolic equations are derived to estimate NSNR, while simulations with more advanced MOSFET models verify the results. The results show a strong tradeoff between NSNR and transconductance tuning range. Resistively generated MOSFETs render the best NSNR results and are robust for future technology developments
Available Techniques for Magnetic Hard Disk Drive Read Channel Equalization
This paper presents an extensive, non-exhaustive, study of available hard disk drive read channel equalization techniques used in the storage and readback of magnetically stored information. The physical elements and basic principles of the storage processes are introduced together with the basic theoretical definitions and models. Both read and write processes in magnetic storage are explained along with the definition of simple key concepts such as user bit density, intersymbol interference, linear and areal density, read head pulse response models, and coding algorithm
Design of adaptive analog filters for magnetic front-end read channels
Esta tese estuda o projecto e o comportamento de filtros em tempo contínuo de
muito-alta-frequência. A motivação deste trabalho foi a investigação de soluções de filtragem
para canais de leitura em sistemas de gravação e reprodução de dados em suporte
magnético, com custos e consumo (tamanho total inferior a 1 mm2 e consumo inferior a
1mW/polo), inferiores aos circuitos existentes. Nesse sentido, tal como foi feito neste
trabalho, o rápido desenvolvimento das tecnologias de microelectrónica suscitou esforços
muito significativos a nível mundial com o objectivo de se investigarem novas técnicas
de realização de filtros em circuito integrado monolítico, especialmente em tecnologia
CMOS (Complementary Metal Oxide Semiconductor). Apresenta-se um estudo comparativo
a diversos níveis hierárquicos do projecto, que conduziu à realização e caracterização
de soluções com as características desejadas.
Num primeiro nível, este estudo aborda a questão conceptual da gravação e transmissão
de sinal bem como a escolha de bons modelos matemáticos para o tratamento da
informação e a minimização de erro inerente às aproximações na conformidade aos princípios
físicos dos dispositivos caracterizados.
O trabalho principal da tese é focado nos níveis hierárquicos da arquitectura do
canal de leitura e da realização em circuito integrado do seu bloco principal – o bloco de
filtragem. Ao nível da arquitectura do canal de leitura, apresenta-se um estudo alargado
sobre as metodologias existentes de adaptação de sinal e recuperação de dados em suporte
magnético. Este desígnio aparece no âmbito da proposta de uma solução de baixo custo,
baixo consumo, baixa tensão de alimentação e baixa complexidade, alicerçada em tecnologia
digital CMOS, para a realização de um sistema DFE (Decision Feedback Equalization)
com base na igualização de sinal utilizando filtros integrados analógicos em tempo
contínuo.
Ao nível do projecto de realização do bloco de filtragem e das técnicas de implementação
de filtros e dos seus blocos constituintes em circuito integrado, concluiu-se que
a técnica baseada em circuitos de transcondutância e condensadores, também conhecida como filtros gm-C (ou transcondutância-C), é a mais adequada para a realização de filtros
adaptativos em muito-alta-frequência. Definiram-se neste nível hierárquico mais baixo,
dois subníveis de aprofundamento do estudo no âmbito desta tese, nomeadamente: a pesquisa
e análise de estruturas ideais no projecto de filtros recorrendo a representações no
espaço de estados; e, o estudo de técnicas de realização em tecnologia digital CMOS de
circuitos de transcondutância para a implementação de filtros integrados analógicos em
tempo contínuo.
Na sequência deste estudo, apresentam-se e comparam-se duas estruturas de filtros
no espaço de estados, correspondentes a duas soluções alternativas para a realização de
um igualador adaptativo realizado por um filtro contínuo passa-tudo de terceira ordem,
para utilização num canal de leitura de dados em suporte magnético.
Como parte constituinte destes filtros, apresenta-se uma técnica de realização de
circuitos de transcondutância, e de realização de condensadores lineares usando matrizes
de transístores MOSFET para processamento de sinal em muito-alta-frequência realizada
em circuito integrado usando tecnologia digital CMOS submicrométrica. Apresentam-se
métodos de adaptação automática capazes de compensar os erros face aos valores nominais
dos componentes, devidos às tolerâncias inerentes ao processo de fabrico, para os
quais apresentamos os resultados de simulação e de medição experimental obtidos.
Na sequência deste estudo, resultou igualmente a apresentação de um circuito passível
de constituir uma solução para o controlo de posicionamento da cabeça de leitura
em sistemas de gravação/reprodução de dados em suporte magnético. O bloco proposto
é um filtro adaptativo de primeira ordem, com base nos mesmos circuitos de transcondutância
e técnicas de igualação propostos e utilizados na implementação do filtro adaptativo
de igualação do canal de leitura.
Este bloco de filtragem foi projectado e incluído num circuito integrado (Jaguar) de
controlo de posicionamento da cabeça de leitura realizado para a empresa ATMEL em
Colorado Springs, e incluído num produto comercial em parceria com uma empresa escocesa
utilizado em discos rígidos amovíveis.This thesis studies the design and behavior of continuous-time very-high-frequency
filters. The motivation of this work was the search for filtering solutions for the readchannel
in recording and reproduction of data on magnetic media systems, with costs and
consumption (total size less than 1 mm2 and consumption under 1mW/pole), lower than
the available circuits. Accordingly, as was done in this work, the rapid development of
microelectronics technology raised very significant efforts worldwide in order to investigate
new techniques for implementing such filters in monolithic integrated circuit, especially
in CMOS technology (Complementary Metal Oxide Semiconductor). We present
a comparative study on different hierarchical levels of the project, which led to the realization
and characterization of solutions with the desired characteristics.
In the first level, this study addresses the conceptual question of recording and
transmission of signal and the choice of good mathematical models for the processing of
information and minimization of error inherent in the approaches and in accordance with
the principles of the characterized physical devices.
The main work of this thesis is focused on the hierarchical levels of the architecture
of the read channel and the integrated circuit implementation of its main block - the filtering
block. At the architecture level of the read channel this work presents a comprehensive
study on existing methodologies of adaptation and signal recovery of data on
magnetic media. This project appears in the sequence of the proposed solution for a lowcost,
low consumption, low voltage, low complexity, using CMOS digital technology for
the performance of a DFE (Decision Feedback Equalization) based on the equalization of
the signal using integrated analog filters in continuous time.
At the project level of implementation of the filtering block and techniques for implementing
filters and its building components, it was concluded that the technique based
on transconductance circuits and capacitors, also known as gm-C filters is the most appropriate
for the implementation of very-high-frequency adaptive filters. We defined in
this lower level, two sub-levels of depth study for this thesis, namely: research and analysis
of optimal structures for the design of state-space filters, and the study of techniques for the design of transconductance cells in digital CMOS circuits for the implementation
of continuous time integrated analog filters.
Following this study, we present and compare two filtering structures operating in
the space of states, corresponding to two alternatives for achieving a realization of an
adaptive equalizer by the use of a continuous-time third order allpass filter, as part of a
read-channel for magnetic media devices.
As a constituent part of these filters, we present a technique for the realization of
transconductance circuits and for the implementation of linear capacitors using arrays of
MOSFET transistors for signal processing in very-high-frequency integrated circuits using
sub-micrometric CMOS technology. We present methods capable of automatic adjustment
and compensation for deviation errors in respect to the nominal values of the
components inherent to the tolerances of the fabrication process, for which we present
the simulation and experimental measurement results obtained.
Also as a result of this study, is the presentation of a circuit that provides a solution
for the control of the head positioning on recording/playback systems of data on magnetic
media. The proposed block is an adaptive first-order filter, based on the same transconductance
circuits and equalization techniques proposed and used in the implementation
of the adaptive filter for the equalization of the read channel.
This filter was designed and included in an integrated circuit (Jaguar) used to control
the positioning of the read-head done for ATMEL company in Colorado Springs, and
part of a commercial product used in removable hard drives fabricated in partnership with a Scottish company
Advances in Solid State Circuit Technologies
This book brings together contributions from experts in the fields to describe the current status of important topics in solid-state circuit technologies. It consists of 20 chapters which are grouped under the following categories: general information, circuits and devices, materials, and characterization techniques. These chapters have been written by renowned experts in the respective fields making this book valuable to the integrated circuits and materials science communities. It is intended for a diverse readership including electrical engineers and material scientists in the industry and academic institutions. Readers will be able to familiarize themselves with the latest technologies in the various fields
Strategies for enhancing DC gain and settling performance of amplifiers
The operational amplifier (op amp) is one of the most widely used and important building blocks in analog circuit design. High gain and high speed are two important properties of op amps because they determine the settling behavior of the op amps. As supply voltages decrease, the realization of high gain amplifiers with large Gain-Bandwidth-Products (GBW) has become challenging. The major focus in this dissertation is on the negative output impedance gain enhancement technique. The negative impedance gain enhancement technique offers potential for achieving very high gain and energy-efficient fast settling and is low-voltage compatible. Misconceptions that have limited the practical adoption of this gain enhancement technique are discussed. A new negative conductance gain enhancement technique was proposed. The proposed circuit generates a negative conductance with matching requirements for achieving very high DC gain that are less stringent than those for existing -g m gain enhancement schemes. The proposed circuit has potential for precise digital control of a very large DC gain. A prototype fully differential CMOS operational amplifier was designed and fabricated based on the proposed gain enhancement technique. Experimental results which showed a DC gain of 85dB and an output swing of 876mVp-p validated the fundamental performance characteristics of this technique. In a separate section, a new amplifier architecture with bandpass feedforward compensation is presented. It is shown that a bandpass feedforward path can be used to substantially extend the unity-gain-frequency of an operational amplifier. Simulation results predict significant improvements in rise time and settling performance and show that the bandpass compensation scheme is reasonably robust. In the final section, a new technique for asynchronous data recovery based upon using a delay line in the incoming data path is introduced. The proposed data recovery system is well suited for tight tolerance channels and coding systems supporting standards that limit the maximum number of consecutive 0\u27s and 1\u27s in a data stream. This system does not require clock recovery, suffers no loss of data during acquisition, has a reduced sensitivity to jitter in the incoming data and does not exhibit jitter enhancement associated with VCO tracking in a PLL
Automatic tuning for linearly tunable filter
A new tuning scheme for linearly tunable high-Q filters is proposed. The tuning method is based on using the phase information for both frequency and Q factor tuning. There is no need to find out the relationship between a filter's passband magnitude and Q. A gm-C biquadratic filter is designed to demonstrate the proposed tuning circuitry. The project includes a phase locked loop (PLL) based frequency tuning loop, reference clock generator, and differential difference amplifier (DDA) for dealing with frequency and Q factor tuning loop and linearly tunable second order gm-C bandpass filter. Simulation results for a 10 MHz prototype filter using AMI 0.5μm process is presented. The chip testing results show that the automatic frequency tuning error is 2.5% for the 10 MHz case