Localization in smart dust sensor networks

Our research goal is to design a robust localization system that offers good accuracy even in the harsh indoor and outdoor environments by handling problems in the physical layer. In this respect, localization based on ultra-wide band (UWB) technology with time-based ranging is a good candidate because of the fine delay resolution that is provided by UWB signals

Wi-PoS : a low-cost, open source ultra-wideband (UWB) hardware platform with long range sub-GHz backbone

Ultra-wideband (UWB) localization is one of the most promising approaches for indoor localization due to its accurate positioning capabilities, immunity against multipath fading, and excellent resilience against narrowband interference. However, UWB researchers are currently limited by the small amount of feasible open source hardware that is publicly available. We developed a new open source hardware platform, Wi-PoS, for precise UWB localization based on Decawave’s DW1000 UWB transceiver with several unique features: support of both long-range sub-GHz and 2.4 GHz back-end communication between nodes, flexible interfacing with external UWB antennas, and an easy implementation of the MAC layer with the Time-Annotated Instruction Set Computer (TAISC) framework. Both hardware and software are open source and all parameters of the UWB ranging can be adjusted, calibrated, and analyzed. This paper explains the main specifications of the hardware platform, illustrates design decisions, and evaluates the performance of the board in terms of range, accuracy, and energy consumption. The accuracy of the ranging system was below 10 cm in an indoor lab environment at distances up to 5 m, and accuracy smaller than 5 cm was obtained at 50 and 75 m in an outdoor environment. A theoretical model was derived for predicting the path loss and the influence of the most important ground reflection. At the same time, the average energy consumption of the hardware was very low with only 81 mA for a tag node and 63 mA for the active anchor nodes, permitting the system to run for several days on a mobile battery pack and allowing easy and fast deployment on sites without an accessible power supply or backbone network. The UWB hardware platform demonstrated flexibility, easy installation, and low power consumption

Experimental evaluation of UWB indoor positioning for indoor track cycling

Accurate radio frequency (RF)-based indoor localization systems are more and more applied during sports. The most accurate RF-based localization systems use ultra-wideband (UWB) technology; this is why this technology is the most prevalent. UWB positioning systems allow for an in-depth analysis of the performance of athletes during training and competition. There is no research available that investigates the feasibility of UWB technology for indoor track cycling. In this paper, we investigate the optimal position to mount the UWB hardware for that specific use case. Different positions on the bicycle and cyclist were evaluated based on accuracy, received power level, line-of-sight, maximum communication range, and comfort. Next to this, the energy consumption of our UWB system was evaluated. We found that the optimal hardware position was the lower back, with a median ranging error of 22 cm (infrastructure hardware placed at 2.3 m). The energy consumption of our UWB system is also taken into account. Applied to our setup with the hardware mounted at the lower back, the maximum communication range varies between 32.6 m and 43.8 m. This shows that UWB localization systems are suitable for indoor positioning of track cyclists

COMPARING THE ACCURACY OF BLUETOOTH LOW ENERGY AND UWB TECHNOLOGY FOR IN-ROOM POSITIONING

The purpose of this project is to thoroughly compare the accuracy of UWB and BLE distance estimations. A ranging methodology is used to gather data with both technologies, and complex algorithms are used to realize distance estimations with MATLAB. Cramer Rao Lower Bound theory demonstrates that estimations made using UWB are both more accurate and more precise than those made with BLE, where UWB can correctly locate with centimeter accuracy, while BLE is limited to meter accuracy

UWB-assisted real-time localization in wireless sensor networks

A safety monitoring and accident warning system for underground construction site has been designed in our previous work based on wireless sensor networks (WSNs). Real-time localization of mobile targets is crucial for tracking the related incidents. However, the current RSSI-based localization approach struggles to achieve the required performance. This is due to the limited ranging accuracy of RSSI devices. In this paper, we investigate various ways of improving the localization accuracy and propose our solution of a hybrid UWB-assisted approach. We argue that a hybrid UWB-assisted RSSI ranging has the best overall performance for our application. We show with both mathematical analysis and demonstration system that, instead of implementing a full UWB network, our approach can improve the accuracy to our desired level with only a small number of additional UWB anchor nodes. © 2013 IEEE

Accurate Positioning in Ultra-Wideband Systems

Cataloged from PDF version of article.Accurate positioning systems can be realized via ultra-wideband signals due to their high time resolution. In this article, position estimation is studied for UWB systems. After a brief introduction to UWB signals and their positioning applications, two-step positioning systems are investigated from a UWB perspective. It is observed that time-based positioning is well suited for UWB systems. Then time-based UWB ranging is studied in detail, and the main challenges, theoretical limits, and range estimation algorithms are presented. Performance of some practical time-based ranging algorithms is investigated and compared against the maximum likelihood estimator and the theoretical limits. The trade-off between complexity and accuracy is .observe

Detection of UWB ranging measurement quality for collaborative indoor positioning

Wireless communication signals have become popular alternatives for indoor positioning and navigation due to lack of navigation satellite signals in such environments. The signal characteristics determine the method used for positioning as well as the positioning accuracy. Ultra-wideband (UWB) signals, with a typical bandwidth of over 1 GHz, overcome multipath problems in complicated environments. Hence, potentially achieves centimetre-level ranging accuracy in open areas. However, signals can be disrupted when placed in environments with obstructions and cause large ranging errors. This paper proposes a ranging measurement quality indicator (RQI) which detects the UWB measurement quality based on the received signal strength pattern. With a detection validity of more than 83%, the RQI is then implemented in a ranging-based collaborative positioning system. The relative constraint of the collaborative network is adjusted adaptively according to the detected RQI. The proposed detection and positioning algorithm improves positioning accuracy by 80% compared to non-adaptive collaborative positioning

Cooperative Relative Positioning of Mobile Users by Fusing IMU Inertial and UWB Ranging Information

Relative positioning between multiple mobile users is essential for many applications, such as search and rescue in disaster areas or human social interaction. Inertial-measurement unit (IMU) is promising to determine the change of position over short periods of time, but it is very sensitive to error accumulation over long term run. By equipping the mobile users with ranging unit, e.g. ultra-wideband (UWB), it is possible to achieve accurate relative positioning by trilateration-based approaches. As compared to vision or laser-based sensors, the UWB does not need to be with in line-of-sight and provides accurate distance estimation. However, UWB does not provide any bearing information and the communication range is limited, thus UWB alone cannot determine the user location without any ambiguity. In this paper, we propose an approach to combine IMU inertial and UWB ranging measurement for relative positioning between multiple mobile users without the knowledge of the infrastructure. We incorporate the UWB and the IMU measurement into a probabilistic-based framework, which allows to cooperatively position a group of mobile users and recover from positioning failures. We have conducted extensive experiments to demonstrate the benefits of incorporating IMU inertial and UWB ranging measurements.Comment: accepted by ICRA 201

A Low Cost UWB Based Solution for Direct Georeferencing UAV Photogrammetry

Thanks to their flexibility and availability at reduced costs, Unmanned Aerial Vehicles (UAVs) have been recently used on a wide range of applications and conditions. Among these, they can play an important role in monitoring critical events (e.g., disaster monitoring) when the presence of humans close to the scene shall be avoided for safety reasons, in precision farming and surveying. Despite the very large number of possible applications, their usage is mainly limited by the availability of the Global Navigation Satellite System (GNSS) in the considered environment: indeed, GNSS is of fundamental importance in order to reduce positioning error derived by the drift of (low-cost) Micro-Electro-Mechanical Systems (MEMS) internal sensors. In order to make the usage of UAVs possible even in critical environments (when GNSS is not available or not reliable, e.g., close to mountains or in city centers, close to high buildings), this paper considers the use of a low cost Ultra Wide-Band (UWB) system as the positioning method. Furthermore, assuming the use of a calibrated camera, UWB positioning is exploited to achieve metric reconstruction on a local coordinate system. Once the georeferenced position of at least three points (e.g., positions of three UWB devices) is known, then georeferencing can be obtained, as well. The proposed approach is validated on a specific case study, the reconstruction of the façade of a university building. Average error on 90 check points distributed over the building façade, obtained by georeferencing by means of the georeferenced positions of four UWB devices at fixed positions, is 0.29 m. For comparison, the average error obtained by using four ground control points is 0.18 m