Layer assignment and routing optimization for advanced technologies

As VLSI technology scales to deep sub-micron and beyond, it becomes increasingly challenging to achieve timing closure for VLSI design. Since a complete design flow consists of several phases, such as logic synthesis, placement, and routing, interconnect synthesis plays an important role which includes buffer insertion/sizing and timing-driven routing. Although progress has been achieved by many advanced routing techniques, the following aspects can be exploited sufficiently for further improvement: (1) incremental layer assignment for timing optimization; (2) signal routing with the requirement of regularity; (3) power-efficient optical-electrical interconnect paradigm. Thus, to perform the layer assignment and routing optimization for advanced technologies, an automated routing engine in a global view is essential to benefit the interconnect design while satisfying specific requirements. This dissertation proposes a set of algorithms and methodology on layer assignment and routing optimization for advanced technologies. The research includes two timing-driven incremental layer assignment approaches, synergistic topology generation and routing synthesis for signal groups, and optical-electrical routing design for power efficiency. For incremental layer assignment, most of the conventional approaches target via minimization but neglect the timing issues. Meanwhile, via delays are ignored but should be considered in emerging technology nodes. Then two timing-driven incremental layer assignment frameworks are proposed, where all the nets are solved simultaneously with the integration of via delays: (1) optimization of the total sum of net delays and reduction of slew violations; (2) minimization of critical path timing in selected nets. For on-chip signal routing, the bundled bits in one group may have different pin locations, but they have to be routed in a regular manner by sharing common topologies. Very few previous works target inter-bit regularity via multi-layer topology selection. Furthermore, the routability and wire-length of the signal bits should also be optimized. Then an advanced synergistic routing engine is promoted, which is able to not only control routability and wire-length but also guide each bit routing intelligently for design regularity. For optical-electrical co-design routing, optical interconnect shows its advantage due to the dominance of bandwidth-distance-power properties. The previous works lack a detailed exploration of optical-electrical co-design for on-chip interconnects. During the transmission, signal quality can be affected by various loss sources and Electrical to Optical (EO)/Optical to Electrical (OE) conversion overheads should also be considered. Then a power-efficient routing flow for on-chip signals is presented, where optical connections can collaborate with electrical wires seamlessly. The effectiveness of proposed algorithms and techniques is demonstrated in this dissertation. These approaches are able to achieve the improvements regarding specific metrics and eventually benefit the routing flow.Electrical and Computer Engineerin

Chippe : a system for constraint driven behavioral synthesis

This report describes the Chippe system, gives some background previous work and describes several sample design runs of the system. Also presented are the sources of the design tradeoffs used by Chippe, and overview of the internal design model, and experiences using the system

Cycle time optimization by timing driven placement with simultaneous netlist transformations

We present new concepts to integrate logic synthesis and physical design. Our methodology uses general Boolean transformations as known from technology-independent synthesis, and a recursive bi-partitioning placement algorithm. In each partitioning step, the precision of the layout data increases. This allows effective guidance of the logic synthesis operations for cycle time optimization. An additional advantage of our approach is that no complicated layout corrections are needed when the netlist is changed

Throughput-driven floorplanning with wire pipelining

The size of future high-performance SoC is such that the time-of-flight of wires connecting distant pins in the layout can be much higher than the clock period. In order to keep the frequency as high as possible, the wires may be pipelined. However, the insertion of flip-flops may alter the throughput of the system due to the presence of loops in the logic netlist. In this paper, we address the problem of floorplanning a large design where long interconnects are pipelined by inserting the throughput in the cost function of a tool based on simulated annealing. The results obtained on a series of benchmarks are then validated using a simple router that breaks long interconnects by suitably placing flip-flops along the wires

Low Power Processor Architectures and Contemporary Techniques for Power Optimization – A Review

The technological evolution has increased the number of transistors for a given die area significantly and increased the switching speed from few MHz to GHz range. Such inversely proportional decline in size and boost in performance consequently demands shrinking of supply voltage and effective power dissipation in chips with millions of transistors. This has triggered substantial amount of research in power reduction techniques into almost every aspect of the chip and particularly the processor cores contained in the chip. This paper presents an overview of techniques for achieving the power efficiency mainly at the processor core level but also visits related domains such as buses and memories. There are various processor parameters and features such as supply voltage, clock frequency, cache and pipelining which can be optimized to reduce the power consumption of the processor. This paper discusses various ways in which these parameters can be optimized. Also, emerging power efficient processor architectures are overviewed and research activities are discussed which should help reader identify how these factors in a processor contribute to power consumption. Some of these concepts have been already established whereas others are still active research areas. © 2009 ACADEMY PUBLISHER

Back-annotation for interactive data path synthesis

In order to take into account physical design effects, a designer needs a feedback mechanism during interactive data path synthesis. In this paper, we propose a hypergraph model and a back-annotation algorithm which provide a feedback mechanism for back-annotation from physical designs to behavioral descriptions. Given a control data flow graph and its structural design, this back-annotation technique cannot only evaluate the design quality but can also feedback the delay to each edge and node in the graph. Therefore, a designer can identify the critical paths and improve the design. The hypergraph model and the back-annotation algorithm allow us to bridge the gap between the behavioral description and the physical design

Modeling of thermally induced skew variations in clock distribution network

Clock distribution network is sensitive to large thermal gradients on the die as the performance of both clock buffers and interconnects are affected by temperature. A robust clock network design relies on the accurate analysis of clock skew subject to temperature variations. In this work, we address the problem of thermally induced clock skew modeling in nanometer CMOS technologies. The complex thermal behavior of both buffers and interconnects are taken into account. In addition, our characterization of the temperature effect on buffers and interconnects provides valuable insight to designers about the potential impact of thermal variations on clock networks. The use of industrial standard data format in the interface allows our tool to be easily integrated into existing design flow