Modelling commercial vehicle handling and rolling stability

YesThis paper presents a multi-degrees-of-freedom non-linear multibody dynamic model of a three-axle heavy commercial vehicle tractor unit, comprising a subchassis, front and rear leaf spring suspensions, steering system, and ten wheels/tyres, with a semi-trailer comprising two axles and eight wheels/tyres. The investigation is mainly concerned with the rollover stability of the articulated vehicle. The models incorporate all sources of compliance, stiffness, and damping, all with non-linear characteristics, and are constructed and simulated using automatic dynamic analysis of mechanical systems formulation. A constant radius turn test and a single lane change test (according to the ISO Standard) are simulated. The constant radius turn test shows the understeer behaviour of the vehicle, and the single lane change manoeuvre was conducted to show the transient behaviour of the vehicle. Non-stable roll and yaw behaviour of the vehicle is predicted at test speeds .90 km/h. Rollover stability of the vehicle is also investigated using a constant radius turn test with increasing speed. The articulated laden vehicle model predicted increased understeer behaviour, due to higher load acting on the wheels of the middle and rear axles of the tractor and the influence of the semi-trailer, as shown by the reduced yaw rate and the steering angle variation during the constant radius turn. The rollover test predicted a critical lateral acceleration value where complete rollover occurs. Unstable behaviour of the articulated vehicle is also predicted in the single lane change manoeuvre

Sideslip estimation for articulated heavy vehicles at the limits of adhesion

Various active safety systems proposed for articulated heavy goods vehicles (HGVs) require an accurate estimate of vehicle sideslip angle. However in contrast to passenger cars, there has been minimal published research on sideslip estimation for articulated HGVs. State-of-the-art observers, which rely on linear vehicle models, perform poorly when manoeuvring near the limits of tyre adhesion. This paper investigates three nonlinear Kalman filters (KFs) for estimating the tractor sideslip angle of a tractor–semitrailer. These are compared to the current state-of-the-art, through computer simulations and vehicle test data. An unscented KF using a 5 degrees-of-freedom single-track vehicle model with linear adaptive tyres is found to substantially outperform the state-of-the-art linear KF across a range of test manoeuvres on different surfaces, both at constant speed and during emergency braking. Robustness of the observer to parameter uncertainty is also demonstrated.Engineering and Physical Sciences Research Council, Cambridge Vehicle Dynamics Consortiu

The Potential for Performance-Based Standards as the Basis for Truck Size and Weight Regulation in the United States

This research project examines truck size (dimensions) and weight regulation in other countries, worldwide, to identify size and weight regulations that are based on standards of truck performance. Such standards, known as performance-based regulations, are intended to ensure that the allowable size and weight of trucks is governed by safety standards and/or by standards for infrastructure (pavement and bridges) wear. The primary goals of this study were to identify performance-based size and weight regulatory practices from a widely diverse group of 32 jurisdictions worldwide, to determine the applicability of such standards in the United States (U.S.) size and weight regulatory framework, and to identify the barriers to adopting this type of approach to truck size and weight regulation. Even though adopting some performance-based standards may be difficult, the concepts underlying them offer too many advantages not to move forward and use a performance-based framework as a foundation for future size and weight reform. The experiences in other countries such as New Zealand and the European Union indicate that performance-based size and weight regulations can be successfully developed and enforced. However, due to the size of the U.S. road network and the population of the U.S. heavy vehicle fleet not all standards used in other countries may be successfully implemented in the U.S. size and weight regulatory framework

Compendium in Vehicle Motion Engineering

This compendium is written for the course “MMF062 Vehicle Motion Engineering” at Chalmers University of Technology. The compendium covers more than included in that course; both in terms of subsystem designs and in terms of some teasers for more advanced studies of vehicle dynamics. Therefore, it is also useful for the more advanced courses, such as “TME102 Vehicle Modelling and Control”.The overall objective of the compendium is to educate engineers that understand and can contribute to development of good motion and energy functionality of vehicles. The compendium focuses on road vehicles, primarily passenger cars and commercial vehicles. Smaller road vehicles, such as bicycles and single-person cars, are only very briefly addressed. It can be mentioned that there exist a lot of ground-vehicle types not covered at all, such as: off-road/construction vehicles, tracked vehicles, horse wagons, hovercrafts, and railway vehicles.Functions are needed for requirement setting, design and verification. The overall order within the compendium is that models/methods/tools needed to understand each function are placed before the functions. Chapters 3-5 describes (complete vehicle) “functions”, organised after vehicle motion directions:\ub7\ua0\ua0\ua0\ua0\ua0\ua0\ua0\ua0 Chapter 3:\ua0Longitudinal\ua0dynamics\ub7\ua0\ua0\ua0\ua0\ua0\ua0\ua0\ua0 Chapter 4:\ua0Lateral\ua0dynamics\ub7\ua0\ua0\ua0\ua0\ua0\ua0\ua0\ua0 Chapter 5:\ua0Vertical\ua0dynamicsChapter 1 introduces automotive industry and the overall way of working there and defines required pre-knowledge from “product-generic” engineering, e.g. modelling of dynamic systems.Chapter 2 also describes the subsystems relevant for vehicle dynamics:• Wheels and Tyre\ua0• Suspension\ua0• Propulsion\ua0• Braking System\ua0• Steering System\ua0• Environment Sensing SystemThe compendium is released in a new version each year, around October, which is the version your read now. A "latest draft" is more frequently updated and often includes some more, sometimes unfinished, material: https://chalmersuniversity.box.com/s/6igaen1ugcjzuhjziuon08axxiy817f

Fractional Order State Feedback Control for Improved Lateral Stability of Semi-Autonomous Commercial Heavy Vehicles

With the growing development of autonomous and semi-autonomous large commercial heavy vehicles, the lateral stability control of articulated vehicles have caught the attention of researchers recently. Active vehicle front steering (AFS) can enhance the handling performance and stability of articulated vehicles for an emergency highway maneuver scenario. However, with large vehicles such tractor-trailers, the system becomes more complex to control and there is an increased occurrence of instabilities. This research investigates a new control scheme based on fractional calculus as a technique that ensures lateral stability of articulated large heavy vehicles during evasive highway maneuvering scenarios. The control method is first implemented to a passenger vehicle model with 2-axles based on the well-known “bicycle model”. The model is then extended and applied onto larger three-axle commercial heavy vehicles in platooning operations. To validate the proposed new control algorithm, the system is linearized and a fractional order PI state feedback control is developed based on the linearized model. Then using Matlab/Simulink, the developed fractional-order linear controller is implemented onto the non-linear tractor-trailer dynamic model. The tractor-trailer system is modeled based on the conventional integer-order techniques and then a non-integer linear controller is developed to control the system. Overall, results confirm that the proposed controller improves the lateral stability of a tractor-trailer response time by 20% as compared to a professional truck driver during an evasive highway maneuvering scenario. In addition, the effects of variable truck cargo loading and longitudinal speed are evaluated to confirm the robustness of the new control method under a variety of potential operating conditions

Compendium in Vehicle Motion Engineering

This compendium is written for the course “MMF062 Vehicle Motion Engineering” at Chalmers University of Technology. The compendium covers more than included in that course; both in terms of subsystem designs and in terms of some teasers for more advanced studies of vehicle dynamics. Therefore, it is also useful for the more advanced course “TME102 Vehicle Modelling and Control”.The overall objective of the compendium is to educate vehicle dynamists, i.e., engineers that understand and can contribute to development of good motion and energy functionality of vehicles. The compendium focuses on road vehicles, primarily passenger cars and commercial vehicles. Smaller road vehicles, such as bicycles and single-person cars, are only very briefly addressed. It should be mentioned that there exist a lot of ground-vehicle types not covered at all, such as: off-road/construction vehicles, tracked vehicles, horse wagons, hovercrafts, or railway vehicles.Functions are needed for requirement setting, design and verification. The overall order within the compendium is that models/methods/tools needed to understand each function are placed before the functions. Chapters 3-5 describes (complete vehicle) “functions”, organised after vehicle motion directions:\ub7\ua0\ua0\ua0\ua0\ua0\ua0\ua0\ua0 Chapter 3:\ua0Longitudinal\ua0dynamics\ub7\ua0\ua0\ua0\ua0\ua0\ua0\ua0\ua0 Chapter 4:\ua0Lateral\ua0dynamics\ub7\ua0\ua0\ua0\ua0\ua0\ua0\ua0\ua0 Chapter 5:\ua0Vertical\ua0dynamicsChapter 1 introduces automotive industry and the overall way of working there and defines required pre-knowledge from “product-generic” engineering, e.g. modelling of dynamic systems.Chapter 2 also describes the subsystems relevant for vehicle dynamics:• Wheels and Tyre\ua0• Suspension\ua0• Propulsion\ua0• Braking System\ua0• Steering System\ua0• Environment Sensing Syste

Computationally Efficient Nonlinear One-and Two-Track Models for Multitrailer Road Vehicles

This paper presents nonlinear mathematical models of one-and two-track multitrailer vehicles. We derive nonlinear equations of motion in the form of a system of implicit ordinary differential equations (ODEs) by using Lagrangian mechanics. The system of ODEs has the minimum number of states and equations that enables efficient computations yet maintains the most important nonlinear vehicle dynamic behavior and allows actuator coordination and energy consumption evaluation. As examples, we build different models of a 4-unit long combination vehicle, i.e., two-track 11-axle and single-track 6-axle nonlinear models as well as a linear single-track 6-axle model. We compare the performance of these models to experimental data of different driving maneuvers. The nonlinear single-track model demonstrates close dynamic behavior to the experiment, which makes it an efficient alternative to the two-track model. The vehicle equations can be generated automatically by using the code provided in this paper and subsequently used for conducting frequency analysis, evaluating energy consumption, deriving performance measures from simulations, and facilitating optimal control applications that involve combined steering, braking and propulsion control