Implementation of the specification and schematics design for the Ethernet Fronthaul Module

Abstract. This Master’s Thesis covers theory and implementation of a device which is designed using a small base station as a reference. The theory chapter consists of the description and theory of a cloud radio access network architecture, a high data rate interface, an active antenna system and a designed device itself. This theory chapter is used to give reasons why the device is designed. The implementation chapter is divided into two chapters, which explains how the implementation specification is done and how the schematics were drawn. The schematics chapter covers the modifications, which are done to the hardware of the original small base station. Ethernet Fronthaul Moduulin implementointispesifikaation ja piirikaavion suunnittelu. Tiivistelmä. Tämä diplomityö käsittelee pienen tukiasemalaitteen pohjalta suunniteltavan laitteen, siihen liittyvän teorian sekä toteutuksen. Laitteeseen liittyvä teoria muodostuu neljästä kappaleesta, jotka käsittelevät cloud radio access network -arkkitehtuuria, nopean data määrän rajapintaa, aktiivi antenni systeemiä sekä itse suunnitellun laitteen teoriaa. Teorialla pyritään pohjustamaan syitä siihen, minkä vuoksi kyseinen laite on haluttu toteuttaa. Laitteen toteutusta käsittelevä kappale on jaettu kahteen osioon, joissa kuvataan implementointispesifikaation toteutus ja piirikaavioiden piirto. Piirikaavio kappaleessa käsitellään muutokset, jotka on tehty pohjana käytettävän tukiaseman laitteistolle

Fast, Accurate and Detailed NoC Simulations

Network-on-Chip (NoC) architectures have a wide variety of parameters that can be adapted to the designer's requirements. Fast exploration of this parameter space is only possible at a high-level and several methods have been proposed. Cycle and bit accurate simulation is necessary when the actual router's RTL description needs to be evaluated and verified. However, extensive simulation of the NoC architecture with cycle and bit accuracy is prohibitively time consuming. In this paper we describe a simulation method to simulate large parallel homogeneous and heterogeneous network-on-chips on a single FPGA. The method is especially suitable for parallel systems where lengthy cycle and bit accurate simulations are required. As a case study, we use a NoC that was modelled and simulated in SystemC. We simulate the same NoC on the described FPGA simulator. This enables us to observe the NoC behavior under a large variety of traffic patterns. Compared with the SystemC simulation we achieved a speed-up of 80-300, without compromising the cycle and bit level accuracy

Ianus: an Adpative FPGA Computer

Dedicated machines designed for specific computational algorithms can outperform conventional computers by several orders of magnitude. In this note we describe {\it Ianus}, a new generation FPGA based machine and its basic features: hardware integration and wide reprogrammability. Our goal is to build a machine that can fully exploit the performance potential of new generation FPGA devices. We also plan a software platform which simplifies its programming, in order to extend its intended range of application to a wide class of interesting and computationally demanding problems. The decision to develop a dedicated processor is a complex one, involving careful assessment of its performance lead, during its expected lifetime, over traditional computers, taking into account their performance increase, as predicted by Moore's law. We discuss this point in detail

FPGA-based module for SURF extraction

We present a complete hardware and software solution of an FPGA-based computer vision embedded module capable of carrying out SURF image features extraction algorithm. Aside from image analysis, the module embeds a Linux distribution that allows to run programs specifically tailored for particular applications. The module is based on a Virtex-5 FXT FPGA which features powerful configurable logic and an embedded PowerPC processor. We describe the module hardware as well as the custom FPGA image processing cores that implement the algorithm's most computationally expensive process, the interest point detection. The module's overall performance is evaluated and compared to CPU and GPU based solutions. Results show that the embedded module achieves comparable disctinctiveness to the SURF software implementation running in a standard CPU while being faster and consuming significantly less power and space. Thus, it allows to use the SURF algorithm in applications with power and spatial constraints, such as autonomous navigation of small mobile robots

JANUS: an FPGA-based System for High Performance Scientific Computing

This paper describes JANUS, a modular massively parallel and reconfigurable FPGA-based computing system. Each JANUS module has a computational core and a host. The computational core is a 4x4 array of FPGA-based processing elements with nearest-neighbor data links. Processors are also directly connected to an I/O node attached to the JANUS host, a conventional PC. JANUS is tailored for, but not limited to, the requirements of a class of hard scientific applications characterized by regular code structure, unconventional data manipulation instructions and not too large data-base size. We discuss the architecture of this configurable machine, and focus on its use on Monte Carlo simulations of statistical mechanics. On this class of application JANUS achieves impressive performances: in some cases one JANUS processing element outperfoms high-end PCs by a factor ~ 1000. We also discuss the role of JANUS on other classes of scientific applications.Comment: 11 pages, 6 figures. Improved version, largely rewritten, submitted to Computing in Science & Engineerin

Design and FPGA Implementation of CORDIC-based 8-point 1D DCT Processor

CORDIC or CO-ordinate Rotation DIgital Computer is a fast, simple, efficient and powerful algorithm used for diverse Digital Signal Processing applications. Primarily developed for real-time airborne computations, it uses a unique computing technique which is especially suitable for solving the trigonometric relationships involved in plane co-ordinate rotation and conversion from rectangular to polar form. It comprises a special serial arithmetic unit having three shift registers, three adders/subtractors, Look-Up table and special interconnections. Using a prescribed sequence of conditional additions or subtractions the CORDIC arithmetic unit can be controlled to solve either of the following equations: Y’=K (Ycos λ+ Xsin λ) X’=K (Xcos λ - Ysin λ); where K is a constant In this project: • A CORDIC-based processor for sine/cosine calculation was designed using VHDL programming in Xilinx ISE 10.1. The CORDIC module was tested for its functionality and correctness by test-bench analysis. Subsequently, FPGA implementation of the CORDIC core followed by ChipScopePro analysis of the output logic waveforms was performed. • Using this CORDIC core a DCT processor was designed to calculate the 8-point 1D DCT. The functionality and operational correctness of this processor was tested, first on the test-bench and then via ChipScopePro analysis, post FPGA implementation. The output obtained in both the cases was compared with the actual values to test for consistency and the percentage of accuracy was established. Power consumption and FPGA resource utilization were observed. The results obtained were discussed