Automatic synthesis of analog layout : a survey

A review of recent research in the automatic synthesis of physical geometry for analog integrated circuits is presented. On introduction, an explanation of the difficulties involved in analog layout as opposed to digital layout is covered. Review of the literature then follows. Emphasis is placed on the exposition of general methods for addressing problems specific to analog layout, with the details of specific systems only being given when they surve to illustrate these methods well. The conclusion discusses problems remaining and offers a prediction as to how technology will evolve to solve them. It is argued that although progress has been and will continue to be made in the automation of analog IC layout, due to fundamental differences in the nature of analog IC design as opposed to digital design, it should not be expected that the level of automation of the former will reach that of the latter any time soon

Desynchronization: Synthesis of asynchronous circuits from synchronous specifications

Asynchronous implementation techniques, which measure logic delays at run time and activate registers accordingly, are inherently more robust than their synchronous counterparts, which estimate worst-case delays at design time, and constrain the clock cycle accordingly. De-synchronization is a new paradigm to automate the design of asynchronous circuits from synchronous specifications, thus permitting widespread adoption of asynchronicity, without requiring special design skills or tools. In this paper, we first of all study different protocols for de-synchronization and formally prove their correctness, using techniques originally developed for distributed deployment of synchronous language specifications. We also provide a taxonomy of existing protocols for asynchronous latch controllers, covering in particular the four-phase handshake protocols devised in the literature for micro-pipelines. We then propose a new controller which exhibits provably maximal concurrency, and analyze the performance of desynchronized circuits with respect to the original synchronous optimized implementation. We finally prove the feasibility and effectiveness of our approach, by showing its application to a set of real designs, including a complete implementation of the DLX microprocessor architectur

Optimizing Scrubbing by Netlist Analysis for FPGA Configuration Bit Classification and Floorplanning

Existing scrubbing techniques for SEU mitigation on FPGAs do not guarantee an error-free operation after SEU recovering if the affected configuration bits do belong to feedback loops of the implemented circuits. In this paper, we a) provide a netlist-based circuit analysis technique to distinguish so-called critical configuration bits from essential bits in order to identify configuration bits which will need also state-restoring actions after a recovered SEU and which not. Furthermore, b) an alternative classification approach using fault injection is developed in order to compare both classification techniques. Moreover, c) we will propose a floorplanning approach for reducing the effective number of scrubbed frames and d), experimental results will give evidence that our optimization methodology not only allows to detect errors earlier but also to minimize the Mean-Time-To-Repair (MTTR) of a circuit considerably. In particular, we show that by using our approach, the MTTR for datapath-intensive circuits can be reduced by up to 48.5% in comparison to standard approaches

Analyzing safety and fault tolerance using time Petri nets

The application of time Petri net modelling and analysis techniques to safety-critical real-time systems is explored and procedures described which allow analysis of safety, recoverability, and fault tolerance. These procedures can be used to help determine software requirements, to guide the use of fault detection and recovery procedures, to determine conditions which require immediate miti gating action to prevent accidents, etc. Thus it is possible to establish important properties duing the synthesis of the system and software design instead of using guesswork and costly a posteriori analysis

Adaptive Latency Insensitive Protocols andElastic Circuits with Early Evaluation: A Comparative Analysis

AbstractLatency Insensitive Protocols (LIP) and Elastic Circuits (EC) solve the same problem of rendering a design tolerant to additional latencies caused by wires or computational elements. They are performance-limited by a firing semantics that enforces coherency through a lazy evaluation rule: Computation is enabled if all inputs to a block are simultaneously available. Adaptive LIP's (ALIP) and EC with early evaluation (ECEE) increase the performance by relaxing the evaluation rule: Computation is enabled as soon as the subset of inputs needed at a given time is available. Their difference in terms of implementation and behavior in selected cases justifies the need for the comparative analysis reported in this paper. Results have been obtained through simple examples, a single representative case-study already used in the context of both LIP's and EC and through extensive simulations over a suite of benchmarks

Designing algorithms to aid discovery by chemical robots

Recently, automated robotic systems have become very efficient, thanks to improved coupling between sensor systems and algorithms, of which the latter have been gaining significance thanks to the increase in computing power over the past few decades. However, intelligent automated chemistry platforms for discovery orientated tasks need to be able to cope with the unknown, which is a profoundly hard problem. In this Outlook, we describe how recent advances in the design and application of algorithms, coupled with the increased amount of chemical data available, and automation and control systems may allow more productive chemical research and the development of chemical robots able to target discovery. This is shown through examples of workflow and data processing with automation and control, and through the use of both well-used and cutting-edge algorithms illustrated using recent studies in chemistry. Finally, several algorithms are presented in relation to chemical robots and chemical intelligence for knowledge discovery

From FPGA to ASIC: A RISC-V processor experience

This work document a correct design flow using these tools in the Lagarto RISC- V Processor and the RTL design considerations that must be taken into account, to move from a design for FPGA to design for ASIC

VSS : a VHDL synthesis system

This report describes a register transfer synthesis system that allows a designer to interact with the design process. The designer can modify the compiled design by changing the input description, selecting optimization and mapping strategies, or graphically changing the generated design schematic. The VHDL language is used for input and output descriptions. An intermediate representation which incorporates signal typing and component attributes simplifies compilation and facilitates design optimization. The compilation process consists of two phases. First, a design composed of generic components is synthesized from the input description. Second, this design is translated into components from a particular library by a mapper and optimized by a logic optimizer. Redesign to new technologies can be accomplished by changing only the component library