The design and multiplier-less realization of software radio receivers with reduced system delay

This paper studies the design and multiplier-less realization of a new software radio receiver (SRR) with reduced system delay. It employs low-delay finite-impulse response (FIR) and digital allpass filters to effectively reduce the system delay of the multistage decimators in SRRs. The optimal least-square and minimax designs of these low-delay FIR and allpass-based filters are formulated as a semidefinite programming (SDP) problem, which allows zero magnitude constraint at ω = π to be incorporated readily as additional linear matrix inequalities (LMIs). By implementing the sampling rate converter (SRC) using a variable digital filter (VDF) immediately after the integer decimators, the needs for an expensive programmable FIR filter in the traditional SRR is avoided. A new method for the optimal minimax design of this VDF-based SRC using SDP is also proposed and compared with traditional weight least squares method. Other implementation issues including the multiplier-less and digital signal processor (DSP) realizations of the SRR and the generation of the clock signal in the SRC are also studied. Design results show that the system delay and implementation complexities (especially in terms of high-speed variable multipliers) of the proposed architecture are considerably reduced as compared with conventional approaches. © 2004 IEEE.published_or_final_versio

Design and Realization of Fully-digital Microwave and Mm-wave Multi-beam Arrays with FPGA/RF-SOC Signal Processing

There has been a constant increase in data-traffic and device-connections in mobile wireless communications, which led the fifth generation (5G) implementations to exploit mm-wave bands at 24/28 GHz. The next-generation wireless access point (6G and beyond) will need to adopt large-scale transceiver arrays with a combination of multi-input-multi-output (MIMO) theory and fully digital multi-beam beamforming. The resulting high gain array factors will overcome the high path losses at mm-wave bands, and the simultaneous multi-beams will exploit the multi-directional channels due to multi-path effects and improve the signal-to-noise ratio. Such access points will be based on electronic systems which heavily depend on the integration of RF electronics with digital signal processing performed in Field programmable gate arrays (FPGA)/ RF-system-on-chip (SoC). This dissertation is directed towards the investigation and realization of fully-digital phased arrays that can produce wideband simultaneous multi-beams with FPGA or RF-SoC digital back-ends. The first proposed approach is a spatial bandpass (SBP) IIR filter-based beamformer, and is based on the concepts of space-time network resonance. A 2.4 GHz, 16-element array receiver, has been built for real-time experimental verification of this approach. The second and third approaches are respectively based on Discrete Fourier Transform (DFT) theory, and a lens plus focal planar array theory. Lens based approach is essentially an analog model of DFT. These two approaches are verified for a 28 GHz 800 MHz mm-wave implementation with RF-SoC as the digital back-end. It has been shown that for all proposed multibeam beamformer implementations, the measured beams are well aligned with those of the simulated. The proposed approaches differ in terms of their architectures, hardware complexity and costs, which will be discussed as this dissertation opens up. This dissertation also presents an application of multi-beam approaches for RF directional sensing applications to explore white spaces within the spatio-temporal spectral regions. A real-time directional sensing system is proposed to capture the white spaces within the 2.4 GHz Wi-Fi band. Further, this dissertation investigates the effect of electro-magnetic (EM) mutual coupling in antenna arrays on the real-time performance of fully-digital transceivers. Different algorithms are proposed to uncouple the mutual coupling in digital domain. The first one is based on finding the MC transfer function from the measured S-parameters of the antenna array and employing it in a Frost FIR filter in the beamforming backend. The second proposed method uses fast algorithms to realize the inverse of mutual coupling matrix via tridiagonal Toeplitz matrices having sparse factors. A 5.8 GHz 32-element array and 1-7 GHz 7-element tightly coupled dipole array (TCDA) have been employed to demonstrate the proof-of-concept of these algorithms

The Effect of Radiometric Correction on Multicamera Algorithms

We present results confirming the importance of radiometric correction in multicamera applications. Although, we compensate for systematic noise only, we review all noise sources in the video sensor (systematic and random). We use a simple model for radiometric correction of digital images. The correction procedure is tested on the disparity map computation in stereo matching, particularly in a case where stereo usually fails -- almost textureless white surface. Without correcting radiometricly, the matching algorithm matches systematic noise components in the two images. With the correction, after removing the systematic noise, an improvement of 26% to 59% in relative rms of the disparity map is demonstrated (the higher the intensity of the flat field, the better the improvement)

Phase-Locked Loop using a comb filter with fractional delay

A Phase Locked Loop is a feedback system combining a Voltage Controlled Oscillator and a Phase Comparator These are connected so that the oscillator maintains a constant phase angle relative to a reference signal. Phase locked loops can be used, for example to generate stable output frequency signals from a fixed frequency signal. A Comb Filter is a kind of Notch Filter (Non Recursive Filter) that is normally used to remove the harmonic terms from a particular signal. In this Design, a PLL is implemented using a Comb Filter because the main frequencies that are considered noise in the PLL loop are the harmonics of the fundamental frequency. There are 2 objectives of this project report, 1. Implementing Comb Filter Using Fractional Delay 2. Comparision of Frame Based and Typical Discrete Sample Based Implementation of a Comb FilterPostprint (published version

Introduction to Random Signals and Noise

Random signals and noise are present in many engineering systems and networks. Signal processing techniques allow engineers to distinguish between useful signals in audio, video or communication equipment, and interference, which disturbs the desired signal. With a strong mathematical grounding, this text provides a clear introduction to the fundamentals of stochastic processes and their practical applications to random signals and noise. With worked examples, problems, and detailed appendices, Introduction to Random Signals and Noise gives the reader the knowledge to design optimum systems for effectively coping with unwanted signals.\ud \ud Key features:\ud • Considers a wide range of signals and noise, including analogue, discrete-time and bandpass signals in both time and frequency domains.\ud • Analyses the basics of digital signal detection using matched filtering, signal space representation and correlation receiver.\ud • Examines optimal filtering methods and their consequences.\ud • Presents a detailed discussion of the topic of Poisson processed and shot noise.\u

When the Differences in Frequency Domain are Compensated: Understanding and Defeating Modulated Replay Attacks on Automatic Speech Recognition

Automatic speech recognition (ASR) systems have been widely deployed in modern smart devices to provide convenient and diverse voice-controlled services. Since ASR systems are vulnerable to audio replay attacks that can spoof and mislead ASR systems, a number of defense systems have been proposed to identify replayed audio signals based on the speakers' unique acoustic features in the frequency domain. In this paper, we uncover a new type of replay attack called modulated replay attack, which can bypass the existing frequency domain based defense systems. The basic idea is to compensate for the frequency distortion of a given electronic speaker using an inverse filter that is customized to the speaker's transform characteristics. Our experiments on real smart devices confirm the modulated replay attacks can successfully escape the existing detection mechanisms that rely on identifying suspicious features in the frequency domain. To defeat modulated replay attacks, we design and implement a countermeasure named DualGuard. We discover and formally prove that no matter how the replay audio signals could be modulated, the replay attacks will either leave ringing artifacts in the time domain or cause spectrum distortion in the frequency domain. Therefore, by jointly checking suspicious features in both frequency and time domains, DualGuard can successfully detect various replay attacks including the modulated replay attacks. We implement a prototype of DualGuard on a popular voice interactive platform, ReSpeaker Core v2. The experimental results show DualGuard can achieve 98% accuracy on detecting modulated replay attacks.Comment: 17 pages, 24 figures, In Proceedings of the 2020 ACM SIGSAC Conference on Computer and Communications Security (CCS' 20