1,840 research outputs found
PACE: Simple Multi-hop Scheduling for Single-radio 802.11-based Stub Wireless Mesh Networks
IEEE 802.11-based Stub Wireless Mesh Networks (WMNs) are a cost-effective and flexible solution to extend wired network infrastructures. Yet, they suffer from two major problems: inefficiency and unfairness. A number of approaches have been proposed to tackle these problems, but they are too restrictive, highly complex, or require time synchronization and modifications to the IEEE 802.11 MAC.
PACE is a simple multi-hop scheduling mechanism for Stub WMNs overlaid on the IEEE 802.11 MAC that jointly addresses the inefficiency and unfairness problems. It limits transmissions to a single mesh node at each time and ensures that each node has the opportunity to transmit a packet in each network-wide transmission round. Simulation results demonstrate that PACE can achieve optimal network capacity utilization and greatly outperforms state of the art CSMA/CA-based solutions as far as goodput, delay, and fairness are concerned
CapEst: A Measurement-based Approach to Estimating Link Capacity in Wireless Networks
Estimating link capacity in a wireless network is a complex task because the
available capacity at a link is a function of not only the current arrival rate
at that link, but also of the arrival rate at links which interfere with that
link as well as of the nature of interference between these links. Models which
accurately characterize this dependence are either too computationally complex
to be useful or lack accuracy. Further, they have a high implementation
overhead and make restrictive assumptions, which makes them inapplicable to
real networks.
In this paper, we propose CapEst, a general, simple yet accurate,
measurement-based approach to estimating link capacity in a wireless network.
To be computationally light, CapEst allows inaccuracy in estimation; however,
using measurements, it can correct this inaccuracy in an iterative fashion and
converge to the correct estimate. Our evaluation shows that CapEst always
converged to within 5% of the correct value in less than 18 iterations. CapEst
is model-independent, hence, is applicable to any MAC/PHY layer and works with
auto-rate adaptation. Moreover, it has a low implementation overhead, can be
used with any application which requires an estimate of residual capacity on a
wireless link and can be implemented completely at the network layer without
any support from the underlying chipset
Unified radio and network control across heterogeneous hardware platforms
Experimentation is an important step in the investigation of techniques for handling spectrum scarcity or the development of new waveforms in future wireless networks. However, it is impractical and not cost effective to construct custom platforms for each future network scenario to be investigated. This problem is addressed by defining Unified Programming Interfaces that allow common access to several platforms for experimentation-based prototyping, research, and development purposes. The design of these interfaces is driven by a diverse set of scenarios that capture the functionality relevant to future network implementations while trying to keep them as generic as possible. Herein, the definition of this set of scenarios is presented as well as the architecture for supporting experimentation-based wireless research over multiple hardware platforms. The proposed architecture for experimentation incorporates both local and global unified interfaces to control any aspect of a wireless system while being completely agnostic to the actual technology incorporated. Control is feasible from the low-level features of individual radios to the entire network stack, including hierarchical control combinations. A testbed to enable the use of the above architecture is utilized that uses a backbone network in order to be able to extract measurements and observe the overall behaviour of the system under test without imposing further communication overhead to the actual experiment. Based on the aforementioned architecture, a system is proposed that is able to support the advancement of intelligent techniques for future networks through experimentation while decoupling promising algorithms and techniques from the capabilities of a specific hardware platform
Wireless industrial monitoring and control networks: the journey so far and the road ahead
While traditional wired communication technologies have played a crucial role in industrial monitoring and control networks over the past few decades, they are increasingly proving to be inadequate to meet the highly dynamic and stringent demands of today’s industrial applications, primarily due to the very rigid nature of wired infrastructures. Wireless technology, however, through its increased pervasiveness, has the potential to revolutionize the industry, not only by mitigating the problems faced by wired solutions, but also by introducing a completely new class of applications. While present day wireless technologies made some preliminary inroads in the monitoring domain, they still have severe limitations especially when real-time, reliable distributed control operations are concerned. This article provides the reader with an overview of existing wireless technologies commonly used in the monitoring and control industry. It highlights the pros and cons of each technology and assesses the degree to which each technology is able to meet the stringent demands of industrial monitoring and control networks. Additionally, it summarizes mechanisms proposed by academia, especially serving critical applications by addressing the real-time and reliability requirements of industrial process automation. The article also describes certain key research problems from the physical layer communication for sensor networks and the wireless networking perspective that have yet to be addressed to allow the successful use of wireless technologies in industrial monitoring and control networks
- …