Prediction of position errors for an industrial robot, using a model of the robot with parameters acquired from the clamping procedure

A robot should follow a given path as accurately as possible. There are however almost always deviations from the desired path, and when the deviations become too large it may be a problem. Some of the deviations stem from transmissions of the robot, and the deviations become more pronounced when there are process forces and gravitational forces present, that affect the transmissions. When position is measured and controlled on the motor side, characteristics of the transmission are not accounted for in the control of the robot, resulting in deviations from the desired path. There are also deviations from the desired path that stem from links of the robot, due to process forces and gravitational forces that affect the links. To predict the deviations that stem from the transmissions, models of the transmissions were developed and used. Models that should be able to predict the deviations that stem from the links were also developed. To acquire data about the characteristics of the transmissions of a robot, tailored experiments were performed. To acquire the data, the robot’s end-effector was locked to a stiff point in space, the robot’s motors were run, and the robot’s sensors were used to log the data. This procedure is known as a clamping procedure. The collected data were processed to derive parameters that were used in the models of the transmissions. The robot that was used was a KR 300 R2500 ULTRA, which is an industrial robot with six degrees of freedom. Simulations with the models of the transmissions were able to recreate the data from the clamping procedure with great accuracy. This shows that the models of the transmissions, with the parameters derived from the clamping procedure, capture characteristics of the robot, that are not taken into account in the control of the robot, which leads to deviations from the desired path. The next step, that is not a part of this thesis, is to use a model of the whole robot, that contains the models of the transmissions and the links, and to validate that the robot model can recreate the deviations from a given path that the robot takes

Adaptation and Learning for Manipulators and Machining

This thesis presents methods for improving the accuracy and efficiency of tasks performed using different kinds of industrial manipulators, with a focus on the application of machining. Industrial robots offer a flexible and cost-efficient alternative to machine tools for machining, but cannot achieve as high accuracy out of the box. This is mainly caused by non-ideal properties in the robot joints such as backlash and compliance, in combination with the strong process forces that affect the robot during machining operations. In this thesis, three different approaches to improving the robotic machining accuracy are presented. First, a macro/micro-manipulator approach is considered, where an external compensation mechanism is used in combination with the robot, for compensation of high-frequency Cartesian errors. Two different milling scenarios are evaluated, where a significant increase in accuracy was obtained. The accuracy specification of 50 μm was reached for both scenarios. Because of the limited workspace and the higher bandwidth of the compensation mechanism compared to the robot, two different mid-ranging approaches for control of the relative position between the robot and the compensator are developed and evaluated. Second, modeling and identification of robot joints is considered. The proposed method relies on clamping the manipulator end effector and actuating the joints, while measuring joint motor torque and motor position. The joint stiffness and backlash can subsequently be extracted from the measurements, to be used for compensation of the deflections that occur during machining. Third, a model-based iterative learning control (ILC) approach is proposed, where feedback is provided from three different sensors of varying investment costs. Using position measurements from an optical tracking system, an error decrease of up to 84 % was obtained. Measurements of end-effector forces yielded an error decrease of 55 %, and a force-estimation method based on joint motor torques decreased the error by 38 %. Further investigation of ILC methods is considered for a different kind of manipulator, a marine vibrator, for the application of marine seismic acquisition. A frequency-domain ILC strategy is proposed, in order to attenuate undesired overtones and improve the tracking accuracy. The harmonics were suppressed after approximately 20 iterations of the ILC algorithm, and the absolute tracking error was r educed by a factor of approximately 50. The final problem considered in this thesis concerns increasing the efficiency of machining tasks, by minimizing cycle times. A force-control approach is proposed to maximize the feed rate, and a learning algorithm for path planning of the machining path is employed for the case of machining in non-isotropic materials, such as wood. The cycle time was decreased by 14 % with the use of force control, and on average an additional 28 % decrease was achieved by use of a learning algorithm. Furthermore, by means of reinforcement learning, the path-planning algorithm is refined to provide optimal solutions and to incorporate an increased number of machining directions

Topics in Machining with Industrial Robot Manipulators and Optimal Motion Control

Two main topics are considered in this thesis: Machining with industrial robot manipulators and optimal motion control of robots and vehicles. The motivation for research on the first subject is the need for flexible and accurate production processes employing industrial robots as their main component. The challenge to overcome here is to achieve high-accuracy machining solutions, in spite of the strong process forces required for the task. Because of the process forces, the nonlinear dynamics of the manipulator, such as the joint compliance and backlash, may significantly degrade the achieved machining accuracy of the manufactured part. In this thesis, a macro/micro-manipulator configuration is considered to the purpose of increasing the milling accuracy. In particular, a model-based control architecture is developed for control of the macro/micro-manipulator setup. The considered approach is validated by experimental results from extensive milling experiments in aluminium and steel. Related to the problem of high-accuracy milling is the topic of robot modeling. To this purpose, two different approaches are considered; modeling of the quasi-static joint dynamics and dynamic compliance modeling. The first problem is approached by an identification method for determining the joint stiffness and backlash. The second problem is approached by using gray-box identification based on subspace-identification methods. Both identification algorithms are evaluated experimentally. Finally, online state estimation is considered as a means to determine the workspace position and orientation of the robot tool. Kalman Filters and Rao-Blackwellized Particle Filters are employed to the purpose of sensor fusion of internal robot measurements and measurements from an inertial measurement unit for estimation of the desired states. The approaches considered are fully implemented and evaluated on experimental data. The second part of the thesis discusses optimal motion control applied to robot manipulators and road vehicles. A control architecture for online control of a robot manipulator in high-performance path tracking is developed, and the architecture is evaluated in extensive simulations. The main characteristic of the control strategy is that it combines coordinated feedback control along both the tangential and transversal directions of the path; this separation is achieved in the framework of natural coordinates. One motivation for research on optimal control of road vehicles in time-critical maneuvers is the desire to develop improved vehicle-safety systems. In this thesis, a method for solving optimal maneuvering problems using nonlinear optimization is discussed. More specifically, vehicle and tire modeling and the optimization formulations required to get useful solutions to these problems are investigated. The considered method is evaluated on different combinations of chassis and tire models, in maneuvers under different road conditions, and for investigation of optimal maneuvers in systems for electronic stability control. The obtained optimization results in simulations are evaluated and compared

A Process/Machine coupling approach: Application to Robotized Incremental Sheet Forming

International audienceIn this paper, a Process/Machine coupling approach applied to Robotized Incremental Sheet Forming (RISF) is presented. This approach consists in coupling a Finite Element Analysis (FEA) of the process with an elastic modelling of the robot structure to improve the geometrical accuracy of the formed part. The FEA, assuming a rigid machine, is used to evaluate the forces at the interface between the tool and the sheet during the forming stage. These forces are used as input data for the elastic model, to predict and correct the tool path deviations. In order to make the tool path correction more effective, the weight of three numerical and material parameters of the FEA on the predicted forces is investigated. Finally, the proposed method is validated by the comparison of the numerical and experimental tool paths and geometries obtained with or without correction of the tool path

Annals of Scientific Society for Assembly, Handling and Industrial Robotics 2021

This Open Access proceedings presents a good overview of the current research landscape of assembly, handling and industrial robotics. The objective of MHI Colloquium is the successful networking at both academic and management level. Thereby, the colloquium focuses an academic exchange at a high level in order to distribute the obtained research results, to determine synergy effects and trends, to connect the actors in person and in conclusion, to strengthen the research field as well as the MHI community. In addition, there is the possibility to become acquatined with the organizing institute. Primary audience is formed by members of the scientific society for assembly, handling and industrial robotics (WGMHI)

Annals of Scientific Society for Assembly, Handling and Industrial Robotics 2021

This Open Access proceedings presents a good overview of the current research landscape of assembly, handling and industrial robotics. The objective of MHI Colloquium is the successful networking at both academic and management level. Thereby, the colloquium focuses an academic exchange at a high level in order to distribute the obtained research results, to determine synergy effects and trends, to connect the actors in person and in conclusion, to strengthen the research field as well as the MHI community. In addition, there is the possibility to become acquatined with the organizing institute. Primary audience is formed by members of the scientific society for assembly, handling and industrial robotics (WGMHI)

Human-robot interaction for assistive robotics

This dissertation presents an in-depth study of human-robot interaction (HRI) withapplication to assistive robotics. In various studies, dexterous in-hand manipulation is included, assistive robots for Sit-To-stand (STS) assistance along with the human intention estimation. In Chapter 1, the background and issues of HRI are explicitly discussed. In Chapter 2, the literature review introduces the recent state-of-the-art research on HRI, such as physical Human-Robot Interaction (HRI), robot STS assistance, dexterous in hand manipulation and human intention estimation. In Chapter 3, various models and control algorithms are described in detail. Chapter 4 introduces the research equipment. Chapter 5 presents innovative theories and implementations of HRI in assistive robotics, including a general methodology of robotic assistance from the human perspective, novel hardware design, robotic sit-to-stand (STS) assistance, human intention estimation, and control