11 research outputs found
Fabrication and Model Based Position Estimation of Novel Laser Processed Shape Memory Alloy Actuator with an Embedded Strain Gauge Sensor
Shape Memory Alloys have sparked great amount of interest in the eld of actuation
over the past decades. Until now, sensorless position estimation of SMA actuators under
dynamic unknown applied stresses has not been feasible due to the complexity of the system
and the number of unknown parameters which the proposed extra information obtained
from the embedded sensor solves. In this thesis, a novel laser processed NiTi Shape Memory
Alloy (SMA) actuator is proposed containing two di erent material compositions in one
monolithic piece of actuator wire. Each of these compositions behaves di erently at room
temperature, one exhibits a shape memory e ect (SME) for actuation, and the other is
pseudo-elastic (PE) which is used to enable an embedded sensor. Fabrication of the wire
included laser processing, heat-treatment, and cold-working procedures. The actuator
wire was subsequently trained to stabilize its properties using iso-stress thermal cycling.
Additionally, a novel model-based sensorless position estimation algorithm is presented.
Proposed model can estimate the position of the actuator under varying applied stresses
with an approximate accuracy of 95% only using dual resistance measurements across the
two di erent material compositions. The proposed actuator has signi cant application in
robotics, wearables, haptics, automotive, and any other application which the mechanical
load is not known in advance. Two simple position and force controller schemes using the
proposed dual-resistance measurement position (and force) estimation are discussed and
the control results presented. The proposed position estimation algorithm is used for the
feedback-signal of a simple PID position and force controller scheme. Moreover, another
novel sensorless position estimation of SMA actuator wires are presented using the power
measurement of the standing wave cause by the re
ection of a high-frequency signal at an
un-terminated end
Inverse kinematics solution for trajectory tracking using artificial neural networks for SCORBOT ER-4u
This paper presents the kinematic analysis of the SCORBOT-ER 4u robot arm using a Multi-Layered Feed-Forward (MLFF) Neural Network. The SCORBOT-ER 4u is a 5-DOF vertical articulated educational robot with revolute joints. The Denavit-Hartenberg and Geometrical methods are the forward kinematic algorithms used to generate data and train the neural network. The learning of forward-inverse mapping enables the inverse kinematic solution to be found. The algorithm is tested on hardware (SCORBOT-ER 4u) and reliable results are obtained. The modeling and simulations are done using MATLAB 8.0 software
International Workshop on MicroFactories (IWMF 2012): 17th-20th June 2012 Tampere Hall Tampere, Finland
This Workshop provides a forum for researchers and practitioners in industry working on the diverse issues of micro and desktop factories, as well as technologies and processes applicable for micro and desktop factories. Micro and desktop factories decrease the need of factory floor space, and reduce energy consumption and improve material and resource utilization thus strongly supporting the new sustainable manufacturing paradigm. They can be seen also as a proper solution to point-of-need manufacturing of customized and personalized products near the point of need
Image-Based Force Estimation and Haptic Rendering For Robot-Assisted Cardiovascular Intervention
Clinical studies have indicated that the loss of haptic perception is the prime limitation of robot-assisted cardiovascular intervention technology, hindering its global adoption. It causes compromised situational awareness for the surgeon during the intervention and may lead to health risks for the patients. This doctoral research was aimed at developing technology for addressing the limitation of the robot-assisted intervention technology in the provision of haptic feedback. The literature review showed that sensor-free force estimation (haptic cue) on endovascular devices, intuitive surgeon interface design, and haptic rendering within the surgeon interface were the major knowledge gaps. For sensor-free force estimation, first, an image-based force estimation methods based on inverse finite-element methods (iFEM) was developed and validated. Next, to address the limitation of the iFEM method in real-time performance, an inverse Cosserat rod model (iCORD) with a computationally efficient solution for endovascular devices was developed and validated. Afterward, the iCORD was adopted for analytical tip force estimation on steerable catheters. The experimental studies confirmed the accuracy and real-time performance of the iCORD for sensor-free force estimation. Afterward, a wearable drift-free rotation measurement device (MiCarp) was developed to facilitate the design of an intuitive surgeon interface by decoupling the rotation measurement from the insertion measurement. The validation studies showed that MiCarp had a superior performance for spatial rotation measurement compared to other modalities. In the end, a novel haptic feedback system based on smart magnetoelastic elastomers was developed, analytically modeled, and experimentally validated. The proposed haptics-enabled surgeon module had an unbounded workspace for interventional tasks and provided an intuitive interface. Experimental validation, at component and system levels, confirmed the usability of the proposed methods for robot-assisted intervention systems
Design optimisation of shape memory alloy linear actuator applications
Shape memory alloy (SMA) actuators have drawn much attention and interest in recent decades due to their unique properties; and, are expected to be increasingly integrated within commercial automotive applications. Key advantages of SMA actuators include: potentially simplified construction, whereby the SMA can act as both sensor and actuator simultaneously; compatibility with Joule heating and convective ambient cooling; and, potential mass advantages over competing actuation technologies. These attributes potentially allow for the development of simpler, more reliable and cost effective actuation systems with significant reduction in mechanical complexity and size. SMA is readily available in commercial quantities and exhibits high wear resistance and durability, which make it an ideal candidate for application in automotive grade applications. Despite these identified advantages, SMA actuators are subject to a series of technical challenges associated with:  - Relatively small strain (displacement or stroke)  - Achievable frequency (actuation speed)  - Controllability (and stability)  - Positional accuracy  - Energy efficiency These technical challenges contribute to a relatively low success rate of commercial SMA actuator applications; and, provide motivation for this program to generate relevant research outcomes that enhance the commercialisation of SMA actuators. An extensive literature review of over 500 journal and patent documents was conducted to provide a clear roadmap for the commercial imperatives for SMA design. The formulated research methodology identifies milestones required for achieving the research objectives, which were addressed as research themes. Based on this literature review, the following research themes were identified:  - Design methods to resolve SMA actuator limitations  - Development of simple and practical numerical models for SMA actuator response  - Data for SMA linear actuator design Specific research contributions within these themes are presented within the thesis, with the objective of enhancing the commercial application of shape memory alloy (SMA) linear actuators, and include:  - A comprehensive analysis of SMAs: history, commercial applications, strength and limitations, design challenges and         opportunities.  - A novel investigation of transient heat transfer scenarios for cylindrical systems associated with their crossover and critical radii.  - Development of novel latent heat models for analytical and numerical applications, and proposal of readily applied activation and deactivation charts compatible with the requirements of SMA actuator designers.  - A novel investigation of the morphological effects of SMA-pulley systems (i.e. pulley diameter, SMA and lagging diameter) on structural and functional fatigue
Soft Robotics: Design for Simplicity, Performance, and Robustness of Robots for Interaction with Humans.
This thesis deals with the design possibilities concerning the next generation of advanced Robots. Aim of the work is to study, analyse and realise artificial systems that are essentially simple, performing and robust and can live and coexist with humans. The main design guideline followed in doing so is the Soft Robotics Approach, that implies the design of systems with intrinsic mechanical compliance in their architecture. The first part of the thesis addresses design of new soft robotics actuators, or robotic muscles. At the beginning are provided information about what a robotic muscle is and what is needed to realise it. A possible classification of these systems is analysed and some criteria useful for their comparison are explained. After, a set of functional specifications and parameters is identified and defined, to characterise a specific subset of this kind of actuators, called Variable Stiffness Actuators. The selected parameters converge in a data-sheet that easily defines performance and abilities of the robotic system. A complete strategy for the design and realisation of this kind of system is provided, which takes into account their me- chanical morphology and architecture. As consequence of this, some new actuators are developed, validated and employed in the execution of complex experimental tasks. In particular the actuator VSA-Cube and its add-on, a Variable Damper, are developed as the main com- ponents of a robotics low-cost platform, called VSA-CubeBot, that
v
can be used as an exploratory platform for multi degrees of freedom experiments. Experimental validations and mathematical models of the system employed in multi degrees of freedom tasks (bimanual as- sembly and drawing on an uneven surface), are reported.
The second part of the thesis is about the design of multi fingered hands for robots. In this part of the work the Pisa-IIT SoftHand is introduced. It is a novel robot hand prototype designed with the purpose of being as easily usable, robust and simple as an industrial gripper, while exhibiting a level of grasping versatility and an aspect comparable to that of the human hand. In the thesis the main theo- retical tool used to enable such simplification, i.e. the neuroscience– based notion of soft synergies, are briefly reviewed. The approach proposed rests on ideas coming from underactuated hand design. A synthesis method to realize a desired set of soft synergies through the principled design of adaptive underactuated mechanisms, which is called the method of adaptive synergies, is discussed. This ap- proach leads to the design of hands accommodating in principle an arbitrary number of soft synergies, as demonstrated in grasping and manipulation simulations and experiments with a prototype. As a particular instance of application of the method of adaptive syner- gies, the Pisa–IIT SoftHand is then described in detail. The design and implementation of the prototype hand are shown and its effec- tiveness demonstrated through grasping experiments. Finally, control of the Pisa/IIT Hand is considered. Few different control strategies are adopted, including an experimental setup with the use of surface Electromyographic signals
41st Aerospace Mechanisms Symposium
The proceedings of the 41st Aerospace Mechanisms Symposium are reported. JPL hosted the conference, which was held in Pasadena Hilton, Pasadena, California on May 16-18, 2012. Lockheed Martin Space Systems cosponsored the symposium. Technology areas covered include gimbals and positioning mechanisms, components such as hinges and motors, CubeSats, tribology, and Mars Science Laboratory mechanisms
Molecular phylogeny of horseshoe crab using mitochondrial Cox1 gene as a benchmark sequence
An effort to assess the utility of 650 bp Cytochrome C
oxidase subunit I (DNA barcode) gene in delineating the members horseshoe crabs (Family: xiphosura) with closely related sister taxa was made. A total of 33 sequences were extracted from National Center for Biotechnological Information (NCBI) which include horseshoe crabs, beetles, common crabs and scorpion sequences. Constructed phylogram showed beetles are closely related with horseshoe crabs than
common crabs. Scorpion spp were distantly related to
xiphosurans. Phylogram and observed genetic distance (GD) date were also revealed that Limulus polyphemus was closely related with Tachypleus tridentatus than with T.gigas. Carcinoscorpius rotundicauda was distantly related with
L.polyphemus. The observed mean Genetic Distance (GD) value was higher in 3rd codon position in all the selected group of organisms. Among the horseshoe crabs high GC content was observed in L.polyphemus (38.32%) and lowest was observed in T.tridentatus (32.35%). We conclude that COI sequencing (barcoding) could be used in identifying and delineating evolutionary relatedness with closely related specie