Automatic Retraction and Full Cycle Operation for a Class of Airborne Wind Energy Generators

Airborne wind energy systems aim to harvest the power of winds blowing at altitudes higher than what conventional wind turbines reach. They employ a tethered flying structure, usually a wing, and exploit the aerodynamic lift to produce electrical power. In the case of ground-based systems, where the traction force on the tether is used to drive a generator on the ground, a two phase power cycle is carried out: one phase to produce power, where the tether is reeled out under high traction force, and a second phase where the tether is recoiled under minimal load. The problem of controlling a tethered wing in this second phase, the retraction phase, is addressed here, by proposing two possible control strategies. Theoretical analyses, numerical simulations, and experimental results are presented to show the performance of the two approaches. Finally, the experimental results of complete autonomous power generation cycles are reported and compared with first-principle models.Comment: This manuscript is a preprint of a paper submitted for possible publication on the IEEE Transactions on Control Systems Technology and is subject to IEEE Copyright. If accepted, the copy of record will be available at IEEEXplore library: http://ieeexplore.ieee.or

Predictive Control of Autonomous Kites in Tow Test Experiments

In this paper we present a model-based control approach for autonomous flight of kites for wind power generation. Predictive models are considered to compensate for delay in the kite dynamics. We apply Model Predictive Control (MPC), with the objective of guiding the kite to follow a figure-of-eight trajectory, in the outer loop of a two level control cascade. The tracking capabilities of the inner-loop controller depend on the operating conditions and are assessed via a frequency domain robustness analysis. We take the limitations of the inner tracking controller into account by encoding them as optimisation constraints in the outer MPC. The method is validated on a kite system in tow test experiments.Comment: The paper has been accepted for publication in the IEEE Control Systems Letters and is subject to IEEE Control Systems Society copyright. Upon publication, the copy of record will be available at http://ieeexplore.ieee.or

State Estimation for Kite Power Systems with Delayed Sensor Measurements

We present a novel estimation approach for airborne wind energy systems with ground-based control and energy generation. The estimator fuses measurements from an inertial measurement unit attached to a tethered wing and position measurements from a camera as well as line angle sensors in an unscented Kalman filter. We have developed a novel kinematic description for tethered wings to specifically address tether dynamics. The presented approach simultaneously estimates feedback variables for a flight controller as well as model parameters, such as a time-varying delay. We demonstrate the performance of the estimator for experimental flight data and compare it to a state-of-the-art estimator based on inertial measurements

Modeling, identification, estimation and adaptation for the control of power-generating kites

Large-scale kites, flying high-force crosswind trajectories, have been proposed for wind power generation. A two phase operational cycle generates net positive power using a ground-based motor/generator. In the traction phase the kite flies a high-force trajectory while reeling out the generator-connected tethers. A low-force retraction phase reels in the tethers and returns the kite to the start of the cycle. Highly variable conditions and significant uncertainty in the dynamics pose challenges to autonomous, well-controlled flight. The control task is divided into trajectory generation and tracking components and the most uncertain parameters in the model are identified online. The control structure uses these parameters in a robust framework resulting in an experimentally verified adaptive control scheme

Crosswind Kite Control - A Benchmark Problem for Advanced Control and Dynamic Optimization

This article presents a kite control and optimization problem intended as a benchmark problem for advanced control and optimization. We provide an entry point to this exciting renewable energy system for researchers in control and optimization methods looking for a realistic test bench, and/or a useful application case for their theory. The benchmark problem in this paper can be studied in simulation, and a complete Simulink model is provided to facilitate this. The simulated scenario, which reproduces many of the challenges presented by a real system, is based on experimental studies from the literature, industrial data and the first author’s own experience in experimental kite control. In par- ticular, an experimentally validated wind turbulence model is included, which subjects the kite to realistic disturbances. The benchmark problem is that of controlling a kite such that the average line tension is maximized. Two different models are provided: A more comprehensive one is used to simulate the ’plant’, while a simpler ’model’ is used to design and implement control and optimization strategies. This way, uncertainty is present in the form of plant-model mismatch. The outputs of the plant are corrupted by measurement noise. The maximum achievable average line tension for the plant is calculated, which should facilitate the performance comparison of different algorithms. A simple control strategy is implemented on the plant and found to be quite suboptimal, even if the free parameters of the algorithm are well tuned. An open question is whether or not more advanced control algorithms could do better

Airborne Wind Energy Systems: A review of the technologies

Among novel technologies for producing electricity from renewable resources, a new class of wind energy converters has been conceived under the name of Airborne Wind Energy Systems (AWESs). This new generation of systems employs flying tethered wings or aircraft in order to reach winds blowing at atmosphere layers that are inaccessible by traditional wind turbines. Research on AWESs started in the mid seventies, with a rapid acceleration in the last decade. A number of systems based on radically different concepts have been analyzed and tested. Several prototypes have been developed all over the world and the results from early experiments are becoming available. This paper provides a review of the different technologies that have been conceived to harvest the energy of high-altitude winds, specifically including prototypes developed by universities and companies. A classification of such systems is proposed on the basis of their general layout and architecture. The focus is set on the hardware architecture of systems that have been demonstrated and tested in real scenarios. Promising solutions that are likely to be implemented in the close future are also considered

Autonomous take-off and landing of a tethered aircraft: a simulation study

The problem of autonomous launch and landing of a tethered rigid aircraft for airborne wind energy generation is addressed. The system operates with ground-based power conversion and pumping cycles, where the tether is repeatedly reeled in and out of a winch installed on the ground and linked to an electric motor/generator. In order to accelerate the aircraft to take-off speed, the ground station is augmented with a linear motion system composed by a slide translating on rails and controlled by a second motor. An onboard propeller is used to sustain the forward velocity during the ascend of the aircraft. During landing, a slight tension on the line is kept, while the onboard control surfaces are used to align the aircraft with the rails and to land again on them. A model-based, decentralized control approach is proposed, capable to carry out a full cycle of launch, low-tension flight, and landing again on the rails. The derived controller is tested via numerical simulations with a realistic dynamical model of the system, in presence of different wind speeds and turbulence, and its performance in terms of landing accuracy is assessed. This study is part of a project aimed to experimentally verify the launch and landing approach on a small-scale prototype.Comment: This is the longer version of a paper submitted to the 2016 American Control Conference 2016, with more details on the simulation parameter