High efficiency power amplifiers

Postprint (published version

Parallel Doherty RF Power Amplifier For WiMAX Applications

abstract: This work covers the design and implementation of a Parallel Doherty RF Power Amplifier in a GaN HEMT process for medium power macro-cell (16W) base station applications. This work improves the key parameters of a Doherty Power Amplifier including the peak and back-off efficiency, operational instantaneous bandwidth and output power by proposing a Parallel Doherty amplifier architecture. As there is a progression in the wireless communication systems from the first generation to the future 5G systems, there is ever increasing demand for higher data rates which means signals with higher peak-to-average power ratios (PAPR). The present modulation schemes require PAPRs close to 8-10dB. So, there is an urgent need to develop energy efficient power amplifiers that can transmit these high data rate signals. The Doherty Power Amplifier (DPA) is the most common PA architecture in the cellular infrastructure, as it achieves reasonably high back-off power levels with good efficiency. This work advances the DPA architecture by proposing a Parallel Doherty Power Amplifier to broaden the PAs instantaneous bandwidth, designed with frequency range of operation for 2.45 – 2.70 GHz to support WiMAX applications and future broadband signals.Dissertation/ThesisMasters Thesis Electrical Engineering 201

Development of a solid state amplifier for the 3rd harmonic cavity for ALBA synchrotron light source

In Synchrotron Light Source facilities with high energy and low emittance electron beams different techniques for improving the quality of the synchrotron light for the users are applied. With this aim ALBA, the Spanish 3rd generation Synchrotron Light Source, is developing a 3rd Harmonic radiofrequency (RF) system as a system additional to the main RF system of the storage ring. This system will consist of four normal conducting active cavities at 1.5 GHz that will provide the required 1.1 MV accelerating voltage to the electron beam and will be fed by four 20 kW power transmitters. This power will be generated by modular Solid State Power Amplifiers (SSPAs) in a continuous wave mode at 1.5 GHz. On the basis of preliminary studies it has been decided that the architecture of each 20 kW power transmitter is a tree diagram made up of primary 1 kW SSPA modules connected in parallel in a combination array. The present PhD thesis is devoted to the design, building and evaluation of a prototype of the 1 kW SSPA module formed four 250 W primary power amplifier modules. Accordingly, all subsystems, namely input and output matching networks of the 250 W primary module, and a four-way power splitter, a four-way power combiner and a novel directivity compensated directional coupler for the non-invasive power monitoring of the 1 kW power amplifier were also designed and their prototypes were tested. A final evaluation of the combined 1 kW SSPA prototype module was successfully carried out and has shown good performance.En las instalaciones de tipo Fuentes de luz de sincrotrón de haz de electrones de alta energía y baja emitancia se aplican diferentes técnicas de mejora de la calidad de la luz de sincrotrón. Con este objetivo, el ALBA, la fuente española de luz de sincrotrón de la tercera generación, está desarrollando un sistema de radiofrecuencia (RF) de la 3ª Harmónica como un sistema adicional al sistema de RF principal del anillo de almacenamiento. Este sistema consistirá de cuatro cavidades activas de conductividad normal de frecuencia 1,5 GHz que suministrarán un voltaje acelerador de 1.1 MV necesario para el haz de electrones y que serán alimentadas por cuatro transmisores de potencia de 20 kW. Esta potencia será generada en modo de onda continua a frecuencia 1.5 GHz por amplificadores de potencia de estado sólido (APES) de estructura modular. A partir de unos estudios preliminares se ha decidido que la arquitectura de cada transmisor de potencia de 20 kW es de tipo diagrama de árbol que consiste de APES primarios de potencia 1 kW conectados en paralelo formando una matriz de combinación. El tema de la presente tesis es el diseño, la construcción y la caracterización de un prototipo del módulo de APES de potencia 1 kW formado por cuatro amplificadores primarios de 250 W de potencia. También, todos subsistemas, concretamente los circuitos de adaptación de entrada y de salida del módulo primario de 250 kW, así como un divisor de cuatro salidas, un combinador de cuatro entradas y un acoplador direccional con una nova solución de compensación de directividad para una monitorización no invasiva han sido diseñados y sus prototipos han sido testeados. La evaluación final de funcionamiento del APES de 1 kW de potencia ha sido realizada con éxito y ha demostrado su buen rendimiento.Postprint (published version

Development of a solid state amplifier for the 3rd harmonic cavity for ALBA synchrotron light source

In Synchrotron Light Source facilities with high energy and low emittance electron beams different techniques for improving the quality of the synchrotron light for the users are applied. With this aim ALBA, the Spanish 3rd generation Synchrotron Light Source, is developing a 3rd Harmonic radiofrequency (RF) system as a system additional to the main RF system of the storage ring. This system will consist of four normal conducting active cavities at 1.5 GHz that will provide the required 1.1 MV accelerating voltage to the electron beam and will be fed by four 20 kW power transmitters. This power will be generated by modular Solid State Power Amplifiers (SSPAs) in a continuous wave mode at 1.5 GHz. On the basis of preliminary studies it has been decided that the architecture of each 20 kW power transmitter is a tree diagram made up of primary 1 kW SSPA modules connected in parallel in a combination array. The present PhD thesis is devoted to the design, building and evaluation of a prototype of the 1 kW SSPA module formed four 250 W primary power amplifier modules. Accordingly, all subsystems, namely input and output matching networks of the 250 W primary module, and a four-way power splitter, a four-way power combiner and a novel directivity compensated directional coupler for the non-invasive power monitoring of the 1 kW power amplifier were also designed and their prototypes were tested. A final evaluation of the combined 1 kW SSPA prototype module was successfully carried out and has shown good performance.En las instalaciones de tipo Fuentes de luz de sincrotrón de haz de electrones de alta energía y baja emitancia se aplican diferentes técnicas de mejora de la calidad de la luz de sincrotrón. Con este objetivo, el ALBA, la fuente española de luz de sincrotrón de la tercera generación, está desarrollando un sistema de radiofrecuencia (RF) de la 3ª Harmónica como un sistema adicional al sistema de RF principal del anillo de almacenamiento. Este sistema consistirá de cuatro cavidades activas de conductividad normal de frecuencia 1,5 GHz que suministrarán un voltaje acelerador de 1.1 MV necesario para el haz de electrones y que serán alimentadas por cuatro transmisores de potencia de 20 kW. Esta potencia será generada en modo de onda continua a frecuencia 1.5 GHz por amplificadores de potencia de estado sólido (APES) de estructura modular. A partir de unos estudios preliminares se ha decidido que la arquitectura de cada transmisor de potencia de 20 kW es de tipo diagrama de árbol que consiste de APES primarios de potencia 1 kW conectados en paralelo formando una matriz de combinación. El tema de la presente tesis es el diseño, la construcción y la caracterización de un prototipo del módulo de APES de potencia 1 kW formado por cuatro amplificadores primarios de 250 W de potencia. También, todos subsistemas, concretamente los circuitos de adaptación de entrada y de salida del módulo primario de 250 kW, así como un divisor de cuatro salidas, un combinador de cuatro entradas y un acoplador direccional con una nova solución de compensación de directividad para una monitorización no invasiva han sido diseñados y sus prototipos han sido testeados. La evaluación final de funcionamiento del APES de 1 kW de potencia ha sido realizada con éxito y ha demostrado su buen rendimiento

Advanced High Efficiency and Broadband Power Amplifiers Based on GaN HEMT for Wireless Applications

In advanced wireless communication systems, a rapid increase in the mobile data traffic and broad information bandwidth requirement can lead to the use of complex spectrally efficient modulation schemes such as orthogonal frequency-division multiplexing (OFDM). Generally, complex non-constant envelope modulated signals have very high peak-to-average ratios (PAPR). Doherty Power Amplifier (DPA) is the most commonly used power amplifier (PA) architecture for meeting high efficiency requirement in advanced communication systems, in the presence of high PAPR signals. However, limited bandwidth of the conventional DPA is often identified as a bottleneck for widespread deployment in base-station application for multi-standard communication signals. The research in this thesis focuses on the development of new designs to overcome the bandwidth limitations of a conventional PA. In particular, the bandwidth limitation factors of a conventional DPA architecture are studied. Moreover, a novel design technique is proposed for DPA’s bandwidth extension. In the first PA design, limited bandwidth and linearity problems are addressed simultaneously. For this purpose, a new Class-AB PA with extended bandwidth and improved linearity is presented for LTE 5 W pico-cell base-station over a frequency range of 1.9–2.5 GHz. A two-tone load/source-pull and bias point optimization techniques are used to extract the sweet spots for optimum efficiency and linearity from the 6 W Cree GaN HEMT device for the whole frequency band. The realized prototype presented saturated PAE higher than 60%, a power gain of 13 dB and an average output power of 36.5 dBm over the desired bandwidth. The proposed PA is also characterized by QAM-256 and LTE input communication signals for linearity characterization. Measured ACPRs are lower than -40 dBc for an input power of 17 dBm. The documented results indicate that the proposed Class-AB architecture is suitable for pico-cell base-station application. In the second PA design, an inherent bandwidth limitation of Class-F power amplifier forced by the improper load harmonics terminations at multiple harmonics is investigated and analyzed. It is demonstrated that the impedance tuning of the second and third harmonics at the drain terminal of a transistor is crucial to achieve a broadband performance. The effect of harmonics terminations on power amplifier’s bandwidth up to fourth harmonics is investigated. The implemented broadband Class-F PA achieved maximum saturated drain efficiency 60-77%, and 10 W output power throughout (1.1-2.1 GHz) band. The simulated and measured results verify that the presented Class-F PA is suitable for a high-efficiency system application in wireless communications over a wide range of frequencies. In the third PA design, a single- and dual-input DPA for LTE application in the 3.5 GHz frequency band are presented and compared. The main goal of this study is to improve the performance of gallium–nitride (GaN) Doherty transmitters over a wide bandwidth in the 3.5 GHz frequency band. For this purpose, the linearity-efficiency trade-off for the two proposed architectures is discussed in detail. Simulated results demonstrate that the single- and dual-input DPA exhibited a peak drain efficiency (DE) of 72.4% and 77%, respectively. Both the circuits showed saturated output power more than 42.9 dBm throughout the designed band. Saturated efficiency, gain and bandwidth of dual-input DPA are higher than that of the single-input DPA. On the other side, dual-input DPA linearity is worse as compared to the single-input DPA. In the last PA design, a novel design methodology for ultra-wide band DPA is presented. The bandwidth limitation factors of the conventional Doherty amplifier are discussed on the ground of broadband matching with impedance variation. To extend the DPA bandwidth, three different methods are used such as post-matching, low impedance transformation ratio and the optimization of offset line for wide bandwidth in the proposed design. The proposed Doherty power amplifier was designed and realized based on two 10 W GaN HEMT devices from Cree Inc. The measured results exhibited 42-57% of efficiency at the 6-dB back-off and saturated output power ranges from 41.5 to 43.1 dBm in the frequency range of 1.15 to 2.35 GHz (68.5% fractional bandwidth). Moreover, less than -25 dBc ACPRs are measured at 42 dBm peak output power throughout the designed band. In a nutshell, all power amplifiers presented in this thesis are suitable for wideband operation and their performances are satisfying the required operational standard. Therefore, this thesis has a significant contribution in the domain of high efficiency and broadband power amplifiers

Direct integration of push-pull amplifier and aperture coupled antenna

The work described in this thesis concerns the integration of push-pull class B amplifier and antenna modules. Push-pull class B is well-known with its fruitful advantages of using differential feeding technique, resulting in low distortion, reasonably high efficiency and high output power. Meanwhile, the antenna module in this work is adapted from the aperture-coupled antenna structure due to its degree of freedom to control the variables which provide the best possible topology that could be realised in system on chip or system in package. More generally, the variables allow good coverage of the Smith Chart so that a wide range of odd-mode matching requirements could be met, for different devices and bias condition of a given transistor. The approach also offers additional filtering up to 3rd harmonic in that it comprises identical harmonic traps on both sides of the aperture using resonant stubs to form bandstop filters, which reduce the ripples at the output waveforms, giving them a significant advantage of neat and tight integration of a push-pull transmitting amplifier

Highly efficient linear CMOS power amplifiers for wireless communications

The rapidly expanding wireless market requires low cost, high integration and high performance of wireless communication systems. CMOS technology provides benefits of cost effectiveness and higher levels of integration. However, the design of highly efficient linear CMOS power amplifier that meets the requirement of advanced communication standards is a challenging task because of the inherent difficulties in CMOS technology. The objective of this research is to realize PAs for wireless communication systems that overcoming the drawbacks of CMOS process, and to develop design approaches that satisfying the demands of the industry. In this dissertation, a cascode bias technique is proposed for improving linearity and reliability of the multi-stage cascode CMOS PA. In addition, to achieve load variation immunity characteristic and to enhance matching and stability, a fully-integrated balanced PA is implemented in a 0.18-m CMOS process. A triple-mode balanced PA using switched quadrature coupler is also proposed, and this work saved a large amount of quiescent current and further improved the efficiency in the back-off power. For the low losses and a high quality factor of passive output combining, a transformer-based quadrature coupler was implemented using integrated passive device (IPD) process. Various practical approaches for linear CMOS PA are suggested with the verified results, and they demonstrate the potential PA design approach for WCDMA applications using a standard CMOS technology.PhDCommittee Chair: Kenney, J. Stevenson; Committee Member: Jongman Kim; Committee Member: Kohl, Paul A.; Committee Member: Kornegay, Kevin T.; Committee Member: Lee, Chang-H

60 Watts Broadband Push Pull RF Power Amplifier Using LTCC Technology

The continuous increase in wireless usage forces an immense pressure on wireless communication in terms of increased demand and spectrum scarcity. Service providers for communication services had no choice but to allocate new parts of the spectrum and present new communication standards that are more spectrally efficient. Communication is not only limited to mobile phones but recently attention has been given to intelligent transportation systems (ITS) where cars will be given a significant place in the communication network. Vehicular Ad-Hoc Network (VANET) is already assigned a slice of the spectrum at 5.9GHz using the IEEE802.11p standard also known as Dedicated Short-Range Communication (DSRC); however, this assignment will have limited range and functionality at first, and users are expected to depend on existing wireless mobile channels for some services such as video streaming and car entertainment. Therefore, it is essential to integrate existing wireless mobile communication standards into the skeleton of ITS at launch and most probably permanently. An investigation was carried out regarding the existing communication standards including wireless local area networks (WLAN) and it was found that frequency bands from 400MHz up to 6GHz are being used in various regions around the world. It is also noted that current state of the art transceivers are composed of several transmitter front-ends targeting certain bands and standards. However, the more standards to be supported the more components to be added and the higher the cost not to mention the limited space in mobile devices. Multimode Multiband (MMMB) transmitters are therefore proposed as a potential solution to the existing redundancy in the number of front-end paths in modern transmitters. Broadband amplifiers are an essential part of any MMMB transmitter and they are also among the most challenging especially for high power requirements. This work explains why single ended topologies with efficiencies higher than 50% have a fundamental bandwidth limit such that the highest frequency of operation must be lower than twice the lowest frequency of operation. Hence, Push-Pull amplifier topology is being proposed as it was found that it has inherent broadband capabilities exceeding those of other topologies with comparable efficiency. The major advantage of Push-Pull power amplifiers is its capability of isolating the even harmonics present in the even mode operation of a Push-Pull amplifier from the less critical odd mode harmonics and the fundamental frequency. This separation between even and odd signals comes from the inclusion of a Balun at the output of push-pull amplifiers. Such separation makes it possible to operate amplifiers beyond the existing limit of single ended power amplifiers. To prove the concept, several Baluns were designed and tested and a comparison was made between different topologies in terms of balance, bandwidth and odd and even mode performances; moreover, to illustrate the concept a Push-Pull power amplifier design was implemented using the multilayer Low Temperature Co-fired Ceramics (LTCC) technology with a bandwidth ratio of more than 100%