Improving forwarding mechanisms for mobile personal area networks

This thesis presents novel methods for improving forwarding mechanisms for personal area networks. Personal area networks are formed by interconnecting personal devices such as personal digital assistants, portable multimedia devices, digital cameras and laptop computers, in an ad hoc fashion. These devices are typically characterised by low complexity hardware, low memory and are usually batterypowered. Protocols and mechanisms developed for general ad hoc networking cannot be directly applied to personal area networks as they are not optimised to suit their specific constraints. The work presented herein proposes solutions for improving error control and routing over personal area networks, which are very important ingredients to the good functioning of the network. The proposed Packet Error Correction (PEC) technique resends only a subset of the transmitted packets, thereby reducing the overhead, while ensuring improved error rates. PEC adapts the number of re-transmissible packets to the conditions of the channel so that unnecessary retransmissions are avoided. It is shown by means of computer simulation that PEC behaves better, in terms of error reduction and overhead, than traditional error control mechanisms, which means that it is adequate for low-power personal devices. The proposed C2HR routing protocol, on the other hand, is designed such that the network lifetime is maximised. This is achieved by forwarding packets through the most energy efficient paths. C2HR is a hybrid routing protocol in the sense that it employs table-driven (proactive) as well as on-demand (reactive) components. Proactive routes are the primary routes, i.e., packets are forwarded through those paths when the network is stable; however, in case of failures, the protocol searches for alternative routes on-demand, through which data is routed temporarily. The advantage of C2HR is that data can still be forwarded even when routing is re-converging, thereby increasing the throughput. Simulation results show that the proposed routing method is more energy efficient than traditional least hops routing, and results in higher data throughput. C2HR relies on a network leader for collecting and distributing topology information, which in turn requires an estimate of the underlying topology. Thus, this thesis also proposes a new cooperative leader election algorithm and techniques for estimating network characteristics in mobile environments. The proposed solutions are simulated under various conditions and demonstrate appreciable behaviour

A survey on Bluetooth multi-hop networks

Bluetooth was firstly announced in 1998. Originally designed as cable replacement connecting devices in a point-to-point fashion its high penetration arouses interest in its ad-hoc networking potential. This ad-hoc networking potential of Bluetooth is advertised for years - but until recently no actual products were available and less than a handful of real Bluetooth multi-hop network deployments were reported. The turnaround was triggered by the release of the Bluetooth Low Energy Mesh Profile which is unquestionable a great achievement but not well suited for all use cases of multi-hop networks. This paper surveys the tremendous work done on Bluetooth multi-hop networks during the last 20 years. All aspects are discussed with demands for a real world Bluetooth multi-hop operation in mind. Relationships and side effects of different topics for a real world implementation are explained. This unique focus distinguishes this survey from existing ones. Furthermore, to the best of the authors’ knowledge this is the first survey consolidating the work on Bluetooth multi-hop networks for classic Bluetooth technology as well as for Bluetooth Low Energy. Another individual characteristic of this survey is a synopsis of real world Bluetooth multi-hop network deployment efforts. In fact, there are only four reports of a successful establishment of a Bluetooth multi-hop network with more than 30 nodes and only one of them was integrated in a real world application - namely a photovoltaic power plant. © 2019 The Author

A PROTOCOL SUITE FOR WIRELESS PERSONAL AREA NETWORKS

A Wireless Personal Area Network (WPAN) is an ad hoc network that consists of devices that surround an individual or an object. Bluetooth® technology is especially suitable for formation of WPANs due to the pervasiveness of devices with Bluetooth® chipsets, its operation in the unlicensed Industrial, Scientific, Medical (ISM) frequency band, and its interference resilience. Bluetooth® technology has great potential to become the de facto standard for communication between heterogeneous devices in WPANs. The piconet, which is the basic Bluetooth® networking unit, utilizes a Master/Slave (MS) configuration that permits only a single master and up to seven active slave devices. This structure limitation prevents Bluetooth® devices from directly participating in larger Mobile Ad Hoc Networks (MANETs) and Wireless Personal Area Networks (WPANs). In order to build larger Bluetooth® topologies, called scatternets, individual piconets must be interconnected. Since each piconet has a unique frequency hopping sequence, piconet interconnections are done by allowing some nodes, called bridges, to participate in more than one piconet. These bridge nodes divide their time between piconets by switching between Frequency Hopping (FH) channels and synchronizing to the piconet\u27s master. In this dissertation we address scatternet formation, routing, and security to make Bluetooth® scatternet communication feasible. We define criteria for efficient scatternet topologies, describe characteristics of different scatternet topology models as well as compare and contrast their properties, classify existing scatternet formation approaches based on the aforementioned models, and propose a distributed scatternet formation algorithm that efficiently forms a scatternet topology and is resilient to node failures. We propose a hybrid routing algorithm, using a bridge link agnostic approach, that provides on-demand discovery of destination devices by their address or by the services that devices provide to their peers, by extending the Service Discovery Protocol (SDP) to scatternets. We also propose a link level security scheme that provides secure communication between adjacent piconet masters, within what we call an Extended Scatternet Neighborhood (ESN)

Energy efficiency in short and wide-area IoT technologies—A survey

In the last years, the Internet of Things (IoT) has emerged as a key application context in the design and evolution of technologies in the transition toward a 5G ecosystem. More and more IoT technologies have entered the market and represent important enablers in the deployment of networks of interconnected devices. As network and spatial device densities grow, energy efficiency and consumption are becoming an important aspect in analyzing the performance and suitability of different technologies. In this framework, this survey presents an extensive review of IoT technologies, including both Low-Power Short-Area Networks (LPSANs) and Low-Power Wide-Area Networks (LPWANs), from the perspective of energy efficiency and power consumption. Existing consumption models and energy efficiency mechanisms are categorized, analyzed and discussed, in order to highlight the main trends proposed in literature and standards toward achieving energy-efficient IoT networks. Current limitations and open challenges are also discussed, aiming at highlighting new possible research directions

Distributed Topology Organization and Transmission Scheduling in Wireless Ad Hoc Networks

An ad hoc network is a set of nodes that spontaneously form a multi-hop all-wireless infrastructure without centralized administration. We study two fundamental issues arising in this setting: topology organization and transmission scheduling. In topology organization we consider a system where nodes need to coordinate their transmissions on a non-broadcast frequency hopping channel to discover each other. We devise a symmetric technique where two nodes use a randomized schedule to synchronize and connect in minimum time. This forms the basis for a topology construction protocol where a set of initially unsynchronized nodes are quickly grouped in multiple interconnected communication channels such that the resulting topology is connected subject to channel membership constraints imposed by the physical layer. In the transmission scheduling problem we consider Time Division Multiple Access (TDMA)the network operates with a schedule where at each slot transmissions can be scheduled without conflicts at the intended receivers. TDMA can provide deterministic allocations but typically relies on two restrictive assumptions: network-wide slot synchronization and global knowledge of network topology and traffic requirements. We first introduce an asynchronous TDMA communication model where slot reference for each link is provided locally by the clock of one of the node endpoints. We study the overhead introduced when nodes switch among multiple time references and propose algorithms for its minimization. We then introduce a distributed asynchronous TDMA protocol where nodes dynamically adjust the rates their adjacent links via local slot reassignments to reach a schedule that realizes a set of optimal link rates. We introduce fairness models for both links and multi-hop sessions sharing the network and devise convergent distributed algorithms for computing the optimal rates for each model. These rates are enforced by a distributed algorithm that decides the slots reassigned during each link rate adjustment. For tree topologies we introduce an algorithm that incrementally converges to the optimal schedule in finite time; for arbitrary topologies an efficient heuristic is proposed. Both topology organization and transmission scheduling protocols are implemented over Bluetooth, a technology enabling ad hoc networking applications. Through extensive simulations they demonstrate excellent performance in both static and dynamic scenarios

Modeling of the Transmission Delay in Bluetooth Piconets under Serial Port Profile

Bluetooth is a key connectivity technology for the deployment of wireless Personal Area Networks as far as it is the most popular low power communication feature incorporated in devices such as laptops or smartphones. This paper proposes an analytical model to predict the delay of the transmissions in Bluetooth piconets employing Serial Port Profile (SPP), which is massively implemented by Bluetoothenabled equipments. The characterization includes the impact of the overhead and the segmentation imposed by the different protocols involved in the transmission as well as the delay provoked by the polling process that is executed to regulate the activity of the different slaves in the piconet. The model has been empirically evaluated and tested in actual Bluetooth piconetsMinisterio de Educación y Ciencia TEC2009-13763-C02-0

Device Discovery in Frequency Hopping Wireless Ad Hoc Networks

This research develops a method for efficient discovery of wireless devices for a frequency hopping spread spectrum, synchronous, ad hoc network comprised of clustered sub-networks. The Bluetooth wireless protocol serves as the reference protocol. The development of a discovery, or outreach, method for scatternets requires the characterization of performance metrics of Bluetooth piconets, many of which are unavailable in literature. Precise analytical models characterizing the interference caused to Bluetooth network traffic by inquiring devices, the probability mass function of packet error rates between arbitrary pairs of Bluetooth networks, and Bluetooth discovery time distribution are developed. Based on the characterized performance metrics, three scatternet outreach methods are developed and compared. Outreach methods which actively inquire on a regular basis, as proposed in literature, are shown to produce lower goodput, have greater mean packet delay, require more power, and cause significant delays in discovery. By passively remaining available for outreach, each of these disadvantages is avoided

Wireless sensor network for health monitoring

Wireless Sensor Network (WSN) is becoming a significant enabling technology for a wide variety of applications. Recent advances in WSN have facilitated the realization of pervasive health monitoring for both homecare and hospital environments. Current technological advances in sensors, power-efficient integrated circuits, and wireless communication have allowed the development of miniature, lightweight, low-cost, and smart physiological sensor nodes. These nodes are capable of sensing, processing, and communicating one or more vital signs. Furthermore, they can be used in wireless personal area networks (WPANs) or wireless body sensor networks (WBSNs) for health monitoring. Many studies were performed and/or are under way in order to develop flexible, reliable, secure, real-time, and power-efficient WBSNs suitable for healthcare applications. To efficiently control and monitor a patient’s status as well as to reduce the cost of power and maintenance, IEEE 802.15.4/ZigBee, a communication standard for low-power wireless communication, is developed as a new efficient technology in health monitoring systems. The main contribution of this dissertation is to provide a modeling, analysis, and design framework for WSN health monitoring systems. This dissertation describes the applications of wireless sensor networks in the healthcare area and discusses the related issues and challenges. The main goal of this study is to evaluate the acceptance of the current wireless standard for enabling WSNs for healthcare monitoring in real environment. Its focus is on IEEE 802.15.4/ZigBee protocols combined with hardware and software platforms. Especially, it focuses on Carrier Sense Multiple Access with Collision Avoidance mechanism (CSMA/CA) algorithms for reliable communication in multiple accessing networks. The performance analysis metrics are established through measured data and mathematical analysis. This dissertation evaluates the network performance of the IEEE 802.15.4 unslotted CSMA/CA mechanism for different parameter settings through analytical modeling and simulation. For this protocol, a Markov chain model is used to derive the analytical expression of normalized packet transmission, reliability, channel access delay, and energy consumption. This model is used to describe the stochastic behavior of random access and deterministic behavior of IEEE 802.15.4 CSMA/CA. By using it, the different aspects of health monitoring can be analyzed. The sound transmission of heart beat with other smaller data packet transmission is studied. The obtained theoretical analysis and simulation results can be used to estimate and design the high performance health monitoring systems