148 research outputs found
Flexible Receivers in CMOS for Wireless Communication
Consumers are pushing for higher data rates to support more services that are introduced in mobile applications. As an example, a few years ago video-on-demand was only accessed through landlines, but today wireless devices are frequently used to stream video. To support this, more flexible network solutions have merged in 4G, introducing new technical problems to the mobile terminal. New techniques are thus needed, and this dissertation explores five different ideas for receiver front-ends, that are cost-efficient and flexible both in performance and operating frequency. All ideas have been implemented in chips fabricated in 65 nm CMOS technology and verified by measurements. Paper I explores a voltage-mode receiver front-end where sub-threshold positive feedback transistors are introduced to increase the linearity in combination with a bootstrapped passive mixer. Paper II builds on the idea of 8-phase harmonic rejection, but simplifies it to a 6-phase solution that can reject noise and interferers at the 3rd order harmonic of the local oscillator frequency. This provides a good trade-off between the traditional quadrature mixer and the 8- phase harmonic rejection mixer. Furthermore, a very compact inductor-less low noise amplifier is introduced. Paper III investigates the use of global negative feedback in a receiver front-end, and also introduces an auxiliary path that can cancel noise from the main path. In paper IV, another global feedback based receiver front-end is designed, but with positive feedback instead of negative. By introducing global positive feedback, the resistance of the transistors in a passive mixer-first receiver front-end can be reduced to achieve a lower noise figure, while still maintaining input matching. Finally, paper V introduces a full receiver chain with a single-ended to differential LNA, current-mode downconversion mixers, and a baseband circuity that merges the functionalities of the transimpedance amplifier, channel-select filter, and analog-to-digital converter into one single power-efficient block
A 0.1–5.0 GHz flexible SDR receiver with digitally assisted calibration in 65 nm CMOS
© 2017 Elsevier Ltd. All rights reserved.A 0.1–5.0 GHz flexible software-defined radio (SDR) receiver with digitally assisted calibration is presented, employing a zero-IF/low-IF reconfigurable architecture for both wideband and narrowband applications. The receiver composes of a main-path based on a current-mode mixer for low noise, a high linearity sub-path based on a voltage-mode passive mixer for out-of-band rejection, and a harmonic rejection (HR) path with vector gain calibration. A dual feedback LNA with “8” shape nested inductor structure, a cascode inverter-based TCA with miller feedback compensation, and a class-AB full differential Op-Amp with Miller feed-forward compensation and QFG technique are proposed. Digitally assisted calibration methods for HR, IIP2 and image rejection (IR) are presented to maintain high performance over PVT variations. The presented receiver is implemented in 65 nm CMOS with 5.4 mm2 core area, consuming 9.6–47.4 mA current under 1.2 V supply. The receiver main path is measured with +5 dB m/+5dBm IB-IIP3/OB-IIP3 and +61dBm IIP2. The sub-path achieves +10 dB m/+18dBm IB-IIP3/OB-IIP3 and +62dBm IIP2, as well as 10 dB RF filtering rejection at 10 MHz offset. The HR-path reaches +13 dB m/+14dBm IB-IIP3/OB-IIP3 and 62/66 dB 3rd/5th-order harmonic rejection with 30–40 dB improvement by the calibration. The measured sensitivity satisfies the requirements of DVB-H, LTE, 802.11 g, and ZigBee.Peer reviewedFinal Accepted Versio
Dirty RF Signal Processing for Mitigation of Receiver Front-end Non-linearity
Moderne drahtlose Kommunikationssysteme stellen hohe und teilweise
gegensätzliche Anforderungen an die Hardware der Funkmodule, wie z.B.
niedriger Energieverbrauch, große Bandbreite und hohe Linearität. Die
Gewährleistung einer ausreichenden Linearität ist, neben anderen analogen
Parametern, eine Herausforderung im praktischen Design der Funkmodule. Der
Fokus der Dissertation liegt auf breitbandigen HF-Frontends für
Software-konfigurierbare Funkmodule, die seit einigen Jahren kommerziell
verfügbar sind. Die praktischen Herausforderungen und Grenzen solcher
flexiblen Funkmodule offenbaren sich vor allem im realen Experiment. Eines
der Hauptprobleme ist die Sicherstellung einer ausreichenden analogen
Performanz über einen weiten Frequenzbereich. Aus einer Vielzahl an
analogen Störeffekten behandelt die Arbeit die Analyse und Minderung von
Nichtlinearitäten in Empfängern mit direkt-umsetzender Architektur. Im
Vordergrund stehen dabei Signalverarbeitungsstrategien zur Minderung
nichtlinear verursachter Interferenz - ein Algorithmus, der besser unter
"Dirty RF"-Techniken bekannt ist. Ein digitales Verfahren nach der
Vorwärtskopplung wird durch intensive Simulationen, Messungen und
Implementierung in realer Hardware verifiziert. Um die Lücken zwischen
Theorie und praktischer Anwendbarkeit zu schließen und das Verfahren in
reale Funkmodule zu integrieren, werden verschiedene Untersuchungen
durchgeführt. Hierzu wird ein erweitertes Verhaltensmodell entwickelt, das
die Struktur direkt-umsetzender Empfänger am besten nachbildet und damit
alle Verzerrungen im HF- und Basisband erfasst. Darüber hinaus wird die
Leistungsfähigkeit des Algorithmus unter realen Funkkanal-Bedingungen
untersucht. Zusätzlich folgt die Vorstellung einer ressourceneffizienten
Echtzeit-Implementierung des Verfahrens auf einem FPGA. Abschließend
diskutiert die Arbeit verschiedene Anwendungsfelder, darunter spektrales
Sensing, robuster GSM-Empfang und GSM-basiertes Passivradar. Es wird
gezeigt, dass nichtlineare Verzerrungen erfolgreich in der digitalen
Domäne gemindert werden können, wodurch die Bitfehlerrate gestörter
modulierter Signale sinkt und der Anteil nichtlinear verursachter
Interferenz minimiert wird. Schließlich kann durch das Verfahren die
effektive Linearität des HF-Frontends stark erhöht werden. Damit wird der
zuverlässige Betrieb eines einfachen Funkmoduls unter dem Einfluss der
Empfängernichtlinearität möglich. Aufgrund des flexiblen Designs ist der
Algorithmus für breitbandige Empfänger universal einsetzbar und ist nicht
auf Software-konfigurierbare Funkmodule beschränkt.Today's wireless communication systems place high requirements on the
radio's hardware that are largely mutually exclusive, such as low power
consumption, wide bandwidth, and high linearity. Achieving a sufficient
linearity, among other analogue characteristics, is a challenging issue in
practical transceiver design. The focus of this thesis is on wideband
receiver RF front-ends for software defined radio technology, which became
commercially available in the recent years. Practical challenges and
limitations are being revealed in real-world experiments with these radios.
One of the main problems is to ensure a sufficient RF performance of the
front-end over a wide bandwidth. The thesis covers the analysis and
mitigation of receiver non-linearity of typical direct-conversion receiver
architectures, among other RF impairments. The main focus is on DSP-based
algorithms for mitigating non-linearly induced interference, an approach
also known as "Dirty RF" signal processing techniques. The conceived
digital feedforward mitigation algorithm is verified through extensive
simulations, RF measurements, and implementation in real hardware. Various
studies are carried out that bridge the gap between theory and practical
applicability of this approach, especially with the aim of integrating that
technique into real devices. To this end, an advanced baseband behavioural
model is developed that matches to direct-conversion receiver architectures
as close as possible, and thus considers all generated distortions at RF
and baseband. In addition, the algorithm's performance is verified under
challenging fading conditions. Moreover, the thesis presents a
resource-efficient real-time implementation of the proposed solution on an
FPGA. Finally, different use cases are covered in the thesis that includes
spectrum monitoring or sensing, GSM downlink reception, and GSM-based
passive radar. It is shown that non-linear distortions can be successfully
mitigated at system level in the digital domain, thereby decreasing the bit
error rate of distorted modulated signals and reducing the amount of
non-linearly induced interference. Finally, the effective linearity of the
front-end is increased substantially. Thus, the proper operation of a
low-cost radio under presence of receiver non-linearity is possible. Due to
the flexible design, the algorithm is generally applicable for wideband
receivers and is not restricted to software defined radios
Recommended from our members
Noise and Blocker Cancellation Techniques for Power and Area Efficient Wireless Receivers
The design of mobile wireless devices has always focused on reducing power, area, and cost. This dissertation proposes two techniques that are leveraged to save power and area and therefore cost. The first techniques reduces the noise in the receiver and results in a relaxed power requirement. The second technique filters the blocker on-chip and allows for the removal of bulky off-chip components in a wireless system.
In the first technique a two-path noise-cancellation architecture is used that reduces the noise in the receiver front end. A prototype ultra-wideband (UWB) receiver is designed and fabricated based on this idea in a 130 nm CMOS process. The fabricated prototype achieves an energy efficiency of 0.48 nJ/bit with a sensitivity of -82 dBm while operating across a wide data rate range of 0.1-25 Mb/s.
The second technique is a blocker filtering scheme that extracts the clock from the blocker and helps eliminate bulky off-chip surface acoustic wave (SAW) filter components. Implemented in a 65 nm CMOS process, the filter is able to track the blocker within 1 to 1.6 GHz and provides better than 10 dB of rejection at the notch frequency for blockers from -40 dBm to -10 dBm
A 2.4 Ghz Mimo Wireless Transceiver Design [TK5103.2. Q1 2008 f rb].
Kombinasi antara MIMO dan modulasi kesukuan dianggap sebagai salah satu penyelesaian yang paling berkesan bagi memperbaiki kecekapan spektrum dan meningkatkan kadar data untuk sistem komonikasi tanpa wayar bagi generasi akan datang .
The combination of multiple input multiple output (MIMO) and quadrature modulation is regarded as one of the most promising solutions for improving spectrum efficiency and enhancing data rate for next-generation wireless communication systems
Interference-robust CMOS receivers for IoT:Highly linear RF front-ends at low power
Wireless technologies have brought Internet access to more than half of the world’s population in the last decade. Nowadays, Internet-of-Things (IoT) technology extends the internet connectivity to sensor nodes embedded in machines, animals, and plants. It will soon put us in a realm of billions of interconnected sensor nodes networking and communicating with each other. Such unprecedented growth of wireless devices puts a big challenge of sustainable and robust connectivity in front of us. Concretely, this challenge demands a wireless sensor node with low power and robust connectivity. Radios are the physical interface for sensor nodes with the external world and are one of the power-hungry components in sensor nodes. Hence it is imperative to make them energy-efficient and interference-robust. This thesis explores CMOS passive mixer-first receiver topology to enhance the interference tolerance of receivers in IoT radios. The dissertation proposes a novel N-path filter/mixer topology at the circuit level and a multipath cross-correlation technique at the system level. Two test-chips of mixer-first receiver front ends, using these techniques, are implemented in CMOS FDSOI 22nm technology as a proof-of-concept. The experimental prototypes demonstrate voltage gain in passive mixers and exhibit high-Q widely-tunable RF filtering, large out-of-band and harmonic interferer tolerance, and moderate noise figure while consuming much lower power than several state-of-the-art receivers
Reconfigurable Receiver Front-Ends for Advanced Telecommunication Technologies
The exponential growth of converging technologies, including augmented reality, autonomous vehicles, machine-to-machine and machine-to-human interactions, biomedical and environmental sensory systems, and artificial intelligence, is driving the need for robust infrastructural systems capable of handling vast data volumes between end users and service providers. This demand has prompted a significant evolution in wireless communication, with 5G and subsequent generations requiring exponentially improved spectral and energy efficiency compared to their predecessors. Achieving this entails intricate strategies such as advanced digital modulations, broader channel bandwidths, complex spectrum sharing, and carrier aggregation scenarios. A particularly challenging aspect arises in the form of non-contiguous aggregation of up to six carrier components across the frequency range 1 (FR1). This necessitates receiver front-ends to effectively reject out-of-band (OOB) interferences while maintaining high-performance in-band (IB) operation. Reconfigurability becomes pivotal in such dynamic environments, where frequency resource allocation, signal strength, and interference levels continuously change. Software-defined radios (SDRs) and cognitive radios (CRs) emerge as solutions, with direct RF-sampling receivers offering a suitable architecture in which the frequency translation is entirely performed in digital domain to avoid analog mixing issues. Moreover, direct RF- sampling receivers facilitate spectrum observation, which is crucial to identify free zones, and detect interferences. Acoustic and distributed filters offer impressive dynamic range and sharp roll off characteristics, but their bulkiness and lack of electronic adjustment capabilities limit their practicality. Active filters, on the other hand, present opportunities for integration in advanced CMOS technology, addressing size constraints and providing versatile programmability. However, concerns about power consumption, noise generation, and linearity in active filters require careful consideration.This thesis primarily focuses on the design and implementation of a low-voltage, low-power RFFE tailored for direct sampling receivers in 5G FR1 applications. The RFFE consists of a balun low-noise amplifier (LNA), a Q-enhanced filter, and a programmable gain amplifier (PGA). The balun-LNA employs noise cancellation, current reuse, and gm boosting for wideband gain and input impedance matching. Leveraging FD-SOI technology allows for programmable gain and linearity via body biasing. The LNA's operational state ranges between high-performance and high-tolerance modes, which are apt for sensitivityand blocking tests, respectively. The Q-enhanced filter adopts noise-cancelling, current-reuse, and programmable Gm-cells to realize a fourth-order response using two resonators. The fourth-order filter response is achieved by subtracting the individual response of these resonators. Compared to cascaded and magnetically coupled fourth-order filters, this technique maintains the large dynamic range of second-order resonators. Fabricated in 22-nm FD-SOI technology, the RFFE achieves 1%-40% fractional bandwidth (FBW) adjustability from 1.7 GHz to 6.4 GHz, 4.6 dB noise figure (NF) and an OOB third-order intermodulation intercept point (IIP3) of 22 dBm. Furthermore, concerning the implementation uncertainties and potential variations of temperature and supply voltage, design margins have been considered and a hybrid calibration scheme is introduced. A combination of on-chip and off-chip calibration based on noise response is employed to effectively adjust the quality factors, Gm-cells, and resonance frequencies, ensuring desired bandpass response. To optimize and accelerate the calibration process, a reinforcement learning (RL) agent is used.Anticipating future trends, the concept of the Q-enhanced filter extends to a multiple-mode filter for 6G upper mid-band applications. Covering the frequency range from 8 to 20 GHz, this RFFE can be configured as a fourth-order dual-band filter, two bandpass filters (BPFs) with an OOB notch, or a BPF with an IB notch. In cognitive radios, the filter’s transmission zeros can be positioned with respect to the carrier frequencies of interfering signals to yield over 50 dB blocker rejection
Design of Analog-to-Digital Converters with Embedded Mixing for Ultra-Low-Power Radio Receivers
In the field of radio receivers, down-conversion methods usually rely on one (or more)
explicit mixing stage(s) before the analog-to-digital converter (ADC). These stages not
only contribute to the overall power consumption but also have an impact on area and can
compromise the receiver’s performance in terms of noise and linearity. On the other hand,
most ADCs require some sort of reference signal in order to properly digitize an analog
input signal. The implementation of this reference signal usually relies on bandgap
circuits and reference buffers to generate a constant, stable, dc signal. Disregarding this
conventional approach, the work developed in this thesis aims to explore the viability
behind the usage of a variable reference signal. Moreover, it demonstrates that not only
can an input signal be properly digitized, but also shifted up and down in frequency,
effectively embedding the mixing operation in an ADC. As a result, ADCs in receiver
chains can perform double-duty as both a quantizer and a mixing stage. The lesser known
charge-sharing (CS) topology, within the successive approximation register (SAR) ADCs,
is used for a practical implementation, due to its feature of “pre-charging” the reference
signal prior to the conversion. Simulation results from an 8-bit CS-SAR ADC designed in
a 0.13 μm CMOS technology validate the proposed technique
- …