Optimized Training Design for Wireless Energy Transfer

Radio-frequency (RF) enabled wireless energy transfer (WET), as a promising solution to provide cost-effective and reliable power supplies for energy-constrained wireless networks, has drawn growing interests recently. To overcome the significant propagation loss over distance, employing multi-antennas at the energy transmitter (ET) to more efficiently direct wireless energy to desired energy receivers (ERs), termed \emph{energy beamforming}, is an essential technique for enabling WET. However, the achievable gain of energy beamforming crucially depends on the available channel state information (CSI) at the ET, which needs to be acquired practically. In this paper, we study the design of an efficient channel acquisition method for a point-to-point multiple-input multiple-output (MIMO) WET system by exploiting the channel reciprocity, i.e., the ET estimates the CSI via dedicated reverse-link training from the ER. Considering the limited energy availability at the ER, the training strategy should be carefully designed so that the channel can be estimated with sufficient accuracy, and yet without consuming excessive energy at the ER. To this end, we propose to maximize the \emph{net} harvested energy at the ER, which is the average harvested energy offset by that used for channel training. An optimization problem is formulated for the training design over MIMO Rician fading channels, including the subset of ER antennas to be trained, as well as the training time and power allocated. Closed-form solutions are obtained for some special scenarios, based on which useful insights are drawn on when training should be employed to improve the net transferred energy in MIMO WET systems.Comment: 30 pages, 9 figures, to appear in IEEE Trans. on Communication

On Enabling Concurrent Communications in Wireless Networks

Today innumerable devices use the wireless spectrum for communication, including cell-phones, WiFi devices, military radios, public safety radios, satellite phones etc. This crowding is limiting the experience of each device either through interference or by waiting fortheir turn to communicate. So, how do we allow a limited spectral resource to reliably scale to many more devices? This is possible through concurrent communication where multiple links share the spectrum and communicate simultaneously using multi-antenna techniques. One promising technique is Interference Alignment (IA), that has been shown to be Degrees-of-Freedom optimal under some conditions. Still, IA requires accurate channel knowledge to be effective and its ability to achieve high throughput under time varying wireless conditions is yet unproven. We make progress towards understanding these limitations and provide viable solutions.We study an IA system under different models of the time varying channel and derive expressions for the achieved rate over time and the system throughput. Using these, we can arrive at the optimal duration of the data phase that maximizes throughput. We proposetwo strategies that help to counter the effects of a time varying channel. First, data aided receiver beam-tracking along with link adaptation provides a sizable improvement in the received signal to interference and noise ratio. Second, updating the transmit beams during data transmission using short feedback pilots improves alignment at the receivers. In faster varying channels, we get a more stable achieved rate whereas in slower varying channels, we see additional throughput gains. The conclusion from this work is that an IA system must be trained more frequently than the channel coherence time to ensure high throughput and beam adaptation during the data phase gives significant robustness to the system.Lastly, we present an IA based medium access control (MAC) protocol that outperforms traditional protocols. Our concurrent carrier sense multiple access (CSMA) protocol based on beam-nulling is compatible with CSMA and increases the sum throughput by 2 to 3x.We also show that IA outperforms optimal time division multiple access under time varying conditions. Hence a well-designed IA system can enable reliable concurrent communications in a wireless network

Massive MIMO for Internet of Things (IoT) Connectivity

Massive MIMO is considered to be one of the key technologies in the emerging 5G systems, but also a concept applicable to other wireless systems. Exploiting the large number of degrees of freedom (DoFs) of massive MIMO essential for achieving high spectral efficiency, high data rates and extreme spatial multiplexing of densely distributed users. On the one hand, the benefits of applying massive MIMO for broadband communication are well known and there has been a large body of research on designing communication schemes to support high rates. On the other hand, using massive MIMO for Internet-of-Things (IoT) is still a developing topic, as IoT connectivity has requirements and constraints that are significantly different from the broadband connections. In this paper we investigate the applicability of massive MIMO to IoT connectivity. Specifically, we treat the two generic types of IoT connections envisioned in 5G: massive machine-type communication (mMTC) and ultra-reliable low-latency communication (URLLC). This paper fills this important gap by identifying the opportunities and challenges in exploiting massive MIMO for IoT connectivity. We provide insights into the trade-offs that emerge when massive MIMO is applied to mMTC or URLLC and present a number of suitable communication schemes. The discussion continues to the questions of network slicing of the wireless resources and the use of massive MIMO to simultaneously support IoT connections with very heterogeneous requirements. The main conclusion is that massive MIMO can bring benefits to the scenarios with IoT connectivity, but it requires tight integration of the physical-layer techniques with the protocol design.Comment: Submitted for publicatio