The role of amplitude-to-phase conversion in the generation of oscillator flicker phase noise

The role of amplitude-to-phase conversion as a factor in feedback oscillator flicker phase noise is examined. A limiting stage consisting of parallel-connected opposite polarity diodes operating in a circuit environment contining reactance is shown to exhibit amplitude-to-phase conversion. This mechanism coupled with resistive upconversion provides an indirect route for very low frequency flicker noise to be transferred into the phase of an oscillator signal. It is concluded that this effect is more significant in the lower frequency regimes where the onlinear reactances associated with active devices are overwhelmed by linear reactive elements

Digitally Controlled Oscillator for mm-Wave Frequencies

In the fifth generation of mobile communication, 5G, frequencies above 30 GHz, so-called millimeter-wave (mm-wave) frequencies are expected to play a prominent role. For the synthesis of these frequencies, the all-digital phase locked loop (ADPLL) has recently gained much attention. A core component of the ADPLL is the digitally controlled oscillator (DCO), an oscillator that tunes the frequency discretely. For good performance, the frequency steps must be made very small, while the total tuning range must be large. This thesis covers several coarse- and fine-tuning techniques for DCOs operating at mm-wave frequencies. Three previously not published fine-tuning schemes are presented: The first one tunes the second harmonic, which will, due to the Groszkowski effect, tune the fundamental tone. The second one is a current-modulation scheme, which utilizes the weak current-dependence of the capacitance of a transistor to tune the frequency. In the third one, a digital-to-analog converter (DAC) is connected to the bulk of the differential pair and tunes the frequency by setting the bulk voltage. The advantages and disadvantages of the presented tuning schemes are discussed and compared with previously reported fine-tuning schemes. Two oscillators were implemented at 86 GHz. Both oscillator use the same oscillator core and hence have the same power consumption and tuning range, 14.1 mW and 13.9%. A phase noise of -89.7 dBc/Hz and -111.4 dBc/Hz at 1 MHz and 10 MHz offset, respectively, were achieved, corresponding to a Figure-of-Merit of -178.5 dBc/Hz. The first oscillator is fine-tuned using a combination of a transformer-based fine-tuning and the current modulation scheme presented here. The achieved frequency resolution is 55 kHz, but can easily be made finer. The second oscillator utilizes the bulk bias technique to achieve its fine tuning. The fine-tuning resolution is here dependent on the resolution of the DAC; a 100μV resolution corresponds to a resolution of 50 kHz.n 2011, the global monthly mobile data usage was 0.5 exabytes, or 500 million gigabytes. In 2016, this number had increased to 7 exabytes, an increase by a factor 14 in just five years, and there are no signs of this trend slowing down. To meet the demands of the ever increasing data usage, engineers have begun to investigate the possibility to use significantly higher frequencies, 30 GHz or higher, for mobile communication than what is used today, which is 3 GHz or below. To be able to transmit and receive data at these high frequency, an oscillator capable of operating at these frequencies are required. An oscillator is an electrical circuit that generates an alternating current (a current that first goes one way, and then the other) at a specific frequency. Below is an example to illustrate to function and importance of the oscillator: Imagine driving a car and listening to the radio. Suddenly, a horrendous song starts playing from the radio, so you instantly tune to another station and find some great, smooth jazz. Satisfied, you lean back and drive on. But what exactly happened when you "tuned to another station"? What you really did was changing the frequency of the oscillator, which can be found in the radio receiver of the car. The radio receiver filters out all frequencies, except for the frequency of the local oscillator. So by setting the frequency of the local oscillator to the frequency of the desired radio channel, only this radio channel will reach the speakers of the car. Thus, the oscillator must be able to vary its frequency to any frequency that a radio station can transmit on. While an old car radio may seem like a simple example, the very same principle is used in mobile communication, even at frequencies above 30 GHz. The oscillator is also used in the same way when transmitting signals, so that the signals are transmitted on the correct frequency. The design of the local oscillator is a hot topic among radio engineers. A poorly designed oscillator will ruin the performance of the whole receiver or transmitter. This thesis covers the design of a special type of oscillators, called digital controlled oscillators or DCO, operating at 30 GHz or higher. The frequency of these oscillators are determined by a digital word (ones and zeros), instead of using an analog voltage, which is traditionally used. Digital control results in greater flexibility and higher noise-resilience, but it also means that the frequency can’t be changed continuously, but rather in discrete steps. This discrete behavior will cause noise in the receiver. To minimize this noise, the frequency steps should be minimized. In this thesis, we have proposed a DCO design, operating at 85.5 GHz, which can be tuned almost 7 % in either direction. To our knowledge, no other DCO operates at such high frequencies. In the proposed oscillators the frequency steps are only 55 kHz apart, which is so small that its effect on the radio receiver can, with a good conscience, be ignored. This is achieved with a novel technique that makes tiny, tiny changes in the current that passes through the oscillator

RF CMOS Oscillators for Modern Wireless Applications

While mobile phones enjoy the largest production volume ever of any consumer electronics products, the demands they place on radio-frequency (RF) transceivers are particularly aggressive, especially on integration with digital processors, low area, low power consumption, while being robust against process-voltage-temperature variations. Since mobile terminals inherently operate on batteries, their power budget is severely constrained. To keep up with the ever increasing data-rate, an ever-decreasing power per bit is required to maintain the battery lifetime. The RF oscillator is the second most power-hungry block of a wireless radio (after power amplifiers). Consequently, any power reduction in an RF oscillator will greatly benefit the overall power efficiency of the cellular transceiver. Moreover, the RF oscillators' purity limits the transceiver performance. The oscillator's phase noise results in power leakage into adjacent channels in a transmit mode and reciprocal mixing in a receive mode. On the other hand, the multi-standard and multi-band transceivers that are now trending demand wide tuning range oscillators. However, broadening the oscillator’s tuning range is usually at the expense of die area (cost) or phase noise. The main goal of this book is to bring forth the exciting and innovative RF oscillator structures that demonstrate better phase noise performance, lower cost, and higher power efficiency than currently achievable. Technical topics discussed in RF CMOS Oscillators for Modern Wireless Applications include: Design and analysis of low phase-noise class-F oscillators Analyze a technique to reduce 1/f noise up-conversion in the oscillators Design and analysis of low power/low voltage oscillators Wide tuning range oscillators Reliability study of RF oscillators in nanoscale CMO

RF CMOS Oscillators for Modern Wireless Applications

While mobile phones enjoy the largest production volume ever of any consumer electronics products, the demands they place on radio-frequency (RF) transceivers are particularly aggressive, especially on integration with digital processors, low area, low power consumption, while being robust against process-voltage-temperature variations. Since mobile terminals inherently operate on batteries, their power budget is severely constrained. To keep up with the ever increasing data-rate, an ever-decreasing power per bit is required to maintain the battery lifetime. The RF oscillator is the second most power-hungry block of a wireless radio (after power amplifiers). Consequently, any power reduction in an RF oscillator will greatly benefit the overall power efficiency of the cellular transceiver. Moreover, the RF oscillators' purity limits the transceiver performance. The oscillator's phase noise results in power leakage into adjacent channels in a transmit mode and reciprocal mixing in a receive mode. On the other hand, the multi-standard and multi-band transceivers that are now trending demand wide tuning range oscillators. However, broadening the oscillator’s tuning range is usually at the expense of die area (cost) or phase noise. The main goal of this book is to bring forth the exciting and innovative RF oscillator structures that demonstrate better phase noise performance, lower cost, and higher power efficiency than currently achievable. Technical topics discussed in RF CMOS Oscillators for Modern Wireless Applications include: Design and analysis of low phase-noise class-F oscillators Analyze a technique to reduce 1/f noise up-conversion in the oscillators Design and analysis of low power/low voltage oscillators Wide tuning range oscillators Reliability study of RF oscillators in nanoscale CMO

Reactive Power Imbalances in LC VCOs and their Influence on Phase Noise Mechanisms

Phase-noise mechanisms in cross-coupled LC voltage-controlled oscillators (VCOs) are reviewed based on a physical understanding of reactive power imbalances in the tank and in the active part. These phenomena are proven to be the predominant phase-noise degradation mechanism in relatively low- and high-current operations. Based on this analysis, a technique to suppress these detrimental effects is developed and implemented in an LC VCO design. The measured results confirm the dependencies predicted by the analysis, and the usefulness of the proposed technique to simultaneously optimize the phase noise at high and low offset frequencies. The measured VCO tuning range is 600 MHz, ranging from 2.4 to 3 GHz. The VCO-prescaler circuit exhibits a phase noise from - 88 to -92 dBc/Hz at 15 kHz and from -155 to -160 dBc/Hz at 10 MHz, when the power consumption is 6 and 10 mA for the VCO and 2 mA for the prescaler, and the power supply is 2 V

Superharmonic Injection Locked Quadrature LC VCO Using Current Recycling Architecture

Quadrature LO signal is a key element in many of the RF transceivers which tend to dominate today’s wireless communication technology. The design of a quadrature LC VCO with better phase noise and lower power consumption forms the core of this work. This thesis investigates a coupling mechanism to implement a quadrature voltage controlled oscillator using indirect injection method. The coupling network in this QVCO couples the two LC cores with their super-harmonic and it recycles its bias current back into the LC tank such that the power consumed by the coupling network is insignificant. This recycled current enables the oscillator to achieve higher amplitude of oscillation for the same power consumption compared to conventional design, hence assuring better phase noise. Mathematical analysis has been done to study the mechanism of quadrature operation and mismatch effects of devices on the quadrature phase error of the proposed QVCO. The proposed quadrature LC VCO is designed in TSMC 0.18 μm technology. It is tunable from 2.61 GHz - 2.85 GHz with sensitivity of 240 MHz/V. Its worst case phase noise is -120 dBc/Hz at 1 MHz offset. The total layout area is 1.41 mm^2 and the QVCO core totally draws 3 mA current from 1.8 V supply

Integrated RF oscillators and LO signal generation circuits

This thesis deals with fully integrated LC oscillators and local oscillator (LO) signal generation circuits. In communication systems a good-quality LO signal for up- and down-conversion in transmitters is needed. The LO signal needs to span the required frequency range and have good frequency stability and low phase noise. Furthermore, most modern systems require accurate quadrature (IQ) LO signals. This thesis tackles these challenges by presenting a detailed study of LC oscillators, monolithic elements for good-quality LC resonators, and circuits for IQ-signal generation and for frequency conversion, as well as many experimental circuits. Monolithic coils and variable capacitors are essential, and this thesis deals with good structures of these devices and their proper modeling. As experimental test devices, over forty monolithic inductors and thirty varactors have been implemented, measured and modeled. Actively synthesized reactive elements were studied as replacements for these passive devices. At first glance these circuits show promising characteristics, but closer noise and nonlinearity analysis reveals that these circuits suffer from high noise levels and a small dynamic range. Nine circuit implementations with various actively synthesized variable capacitors were done. Quadrature signal generation can be performed with three different methods, and these are analyzed in the thesis. Frequency conversion circuits are used for alleviating coupling problems or to expand the number of frequency bands covered. The thesis includes an analysis of single-sideband mixing, frequency dividers, and frequency multipliers, which are used to perform the four basic arithmetical operations for the frequency tone. Two design cases are presented. The first one is a single-sideband mixing method for the generation of WiMedia UWB LO-signals, and the second one is a frequency conversion unit for a digital period synthesizer. The last part of the thesis presents five research projects. In the first one a temperature-compensated GaAs MESFET VCO was developed. The second one deals with circuit and device development for an experimental-level BiCMOS process. A cable-modem RF tuner IC using a SiGe process was developed in the third project, and a CMOS flip-chip VCO module in the fourth one. Finally, two frequency synthesizers for UWB radios are presented