19,314 research outputs found
Low Power Processor Architectures and Contemporary Techniques for Power Optimization – A Review
The technological evolution has increased the number of transistors for a given die area significantly and increased the switching speed from few MHz to GHz range. Such inversely proportional decline in size and boost in performance consequently demands shrinking of supply voltage and effective power dissipation in chips with millions of transistors. This has triggered substantial amount of research in power reduction techniques into almost every aspect of the chip and particularly the processor cores contained in the chip. This paper presents an overview of techniques for achieving the power efficiency mainly at the processor core level but also visits related domains such as buses and memories. There are various processor parameters and features such as supply voltage, clock frequency, cache and pipelining which can be optimized to reduce the power consumption of the processor. This paper discusses various ways in which these parameters can be optimized. Also, emerging power efficient processor architectures are overviewed and research activities are discussed which should help reader identify how these factors in a processor contribute to power consumption. Some of these concepts have been already established whereas others are still active research areas. © 2009 ACADEMY PUBLISHER
Division with speculation of quotient digits
The speed of SRT-type dividers is mainly determined by the complexity of the quotient-digit selection, so that implementations are limited to low-radix stages. A scheme is presented in which the quotient-digit is speculated and, when this speculation is incorrect, a rollback or a partial advance is performed. This results in a division operation with a shorter cycle time and a variable number of cycles. Several designs have been realized, and a radix-64 implementation that is 30% faster than the fastest conventional implementation (radix-8) at an increase of about 45% in area per quotient bit has been obtained. A radix-16 implementation that is about 10% faster than the radix-8 conventional one, with the additional advantage of requiring about 25% less area per quotient bit, is also shownPeer ReviewedPostprint (published version
Recommended from our members
On Multicast in Asynchronous Networks-on-Chip: Techniques, Architectures, and FPGA Implementation
In this era of exascale computing, conventional synchronous design techniques are facing unprecedented challenges. The consumer electronics market is replete with many-core systems in the range of 16 cores to thousands of cores on chip, integrating multi-billion transistors. However, with this ever increasing complexity, the traditional design approaches are facing key issues such as increasing chip power, process variability, aging, thermal problems, and scalability. An alternative paradigm that has gained significant interest in the last decade is asynchronous design. Asynchronous designs have several potential advantages: they are naturally energy proportional, burning power only when active, do not require complex clock distribution, are robust to different forms of variability, and provide ease of composability for heterogeneous platforms. Networks-on-chip (NoCs) is an interconnect paradigm that has been introduced to deal with the ever-increasing system complexity. NoCs provide a distributed, scalable, and efficient interconnect solution for today’s many-core systems. Moreover, NoCs are a natural match with asynchronous design techniques, as they separate communication infrastructure and timing from the computational elements. To this end, globally-asynchronous locally-synchronous (GALS) systems that interconnect multiple processing cores, operating at different clock speeds, using an asynchronous NoC, have gained significant interest. While asynchronous NoCs have several advantages, they also face a key challenge of supporting new types of traffic patterns. Once such pattern is multicast communication, where a source sends packets to arbitrary number of destinations. Multicast is not only common in parallel computing, such as for cache coherency, but also for emerging areas such as neuromorphic computing. This important capability has been largely missing from asynchronous NoCs. This thesis introduces several efficient multicast solutions for these interconnects. In particular, techniques, and network architectures are introduced to support high-performance and low-power multicast. Two leading network topologies are the focus: a variant mesh-of-trees (MoT) and a 2D mesh. In addition, for a more realistic implementation and analysis, as well as significantly advancing the field of asynchronous NoCs, this thesis also targets synthesis of these NoCs on commercial FPGAs. While there has been significant advances in FPGA technologies, there has been only limited research on implementing asynchronous NoCs on FPGAs. To this end, a systematic computeraided design (CAD) methodology has been introduced to efficiently and safely map asynchronous NoCs on FPGAs. Overall, this thesis makes the following three contributions. The first contribution is a multicast solution for a variant MoT network topology. This topology consists of simple low-radix switches, and has been used in high-performance computing platforms. A novel local speculation technique is introduced, where a subset of the network’s switches are speculative that always broadcast every packet. These switches are very simple and have high performance. Speculative switches are surrounded by non-speculative ones that route packets based on their destinations and also throttle any redundant copies created by the former. This hybrid network architecture achieved significant performance and power benefits over other multicast approaches. The second contribution is a multicast solution for a 2D-mesh topology, which is more complex with higher-radix switches and also is more commonly used. A novel continuous-time replication strategy is introduced to optimize the critical multi-way forking operation of a multicast transmission. In this technique, a multicast packet is first stored in an input port of a switch, from where it is sent through distinct output ports towards different destinations concurrently, at each output’s own rate and in continuous time. This strategy is shown to have significant latency and energy benefits over an approach that performs multicast using multiple distinct serial unicasts to each destination. Finally, a systematic CAD methodology is introduced to synthesize asynchronous NoCs on commercial FPGAs. A two-fold goal is targeted: correctness and high performance. For ease of implementation, only existing FPGA synthesis tools are used. Moreover, since asynchronous NoCs involve special asynchronous components, a comprehensive guide is introduced to map these elements correctly and efficiently. Two asynchronous NoC switches are synthesized using the proposed approach on a leading Xilinx FPGA in 28 nm: one that only handles unicast, and the other that also supports multicast. Both showed significant energy benefits with some performance gains over a state-of-the-art synchronous switch
- …