On the functional test of the BTB logic in pipelined and superscalar processors

Electronic systems are increasingly used for safety-critical applications, where the effects of faults must be taken under control and hopefully avoided. For this purpose, test of manufactured devices is particularly important, both at the end of the production line and during the operational phase. This paper describes a method to test the logic implementing the Branch Prediction Unit in pipelined and superscalar processors when this follows the Branch Target Buffer (BTB) architecture; the proposed approach is functional, i.e., it is based on forcing the processor to execute a suitably devised test program and observing the produced results. Experimental results are provided on the DLX processor, showing that the method can achieve a high value of stuck-at fault coverage while also testing the memory in the BT

Affordable techniques for dependable microprocessor design

As high computing power is available at an affordable cost, we rely on microprocessor-based systems for much greater variety of applications. This dependence indicates that a processor failure could have more diverse impacts on our daily lives. Therefore, dependability is becoming an increasingly important quality measure of microprocessors.;Temporary hardware malfunctions caused by unstable environmental conditions can lead the processor to an incorrect state. This is referred to as a transient error or soft error. Studies have shown that soft errors are the major source of system failures. This dissertation characterizes the soft error behavior on microprocessors and presents new microarchitectural approaches that can realize high dependability with low overhead.;Our fault injection studies using RISC processors have demonstrated that different functional blocks of the processor have distinct susceptibilities to soft errors. The error susceptibility information must be reflected in devising fault tolerance schemes for cost-sensitive applications. Considering the common use of on-chip caches in modern processors, we investigated area-efficient protection schemes for memory arrays. The idea of caching redundant information was exploited to optimize resource utilization for increased dependability. We also developed a mechanism to verify the integrity of data transfer from lower level memories to the primary caches. The results of this study show that by exploiting bus idle cycles and the information redundancy, an almost complete check for the initial memory data transfer is possible without incurring a performance penalty.;For protecting the processor\u27s control logic, which usually remains unprotected, we propose a low-cost reliability enhancement strategy. We classified control logic signals into static and dynamic control depending on their changeability, and applied various techniques including commit-time checking, signature caching, component-level duplication, and control flow monitoring. Our schemes can achieve more than 99% coverage with a very small hardware addition. Finally, a virtual duplex architecture for superscalar processors is presented. In this system-level approach, the processor pipeline is backed up by a partially replicated pipeline. The replication-based checker minimizes the design and verification overheads. For a large-scale superscalar processor, the proposed architecture can bring 61.4% reduction in die area while sustaining the maximum performance

Timing speculation and adaptive reliable overclocking techniques for aggressive computer systems

Computers have changed our lives beyond our own imagination in the past several decades. The continued and progressive advancements in VLSI technology and numerous micro-architectural innovations have played a key role in the design of spectacular low-cost high performance computing systems that have become omnipresent in today\u27s technology driven world. Performance and dependability have become key concerns as these ubiquitous computing machines continue to drive our everyday life. Every application has unique demands, as they run in diverse operating environments. Dependable, aggressive and adaptive systems improve efficiency in terms of speed, reliability and energy consumption. Traditional computing systems run at a fixed clock frequency, which is determined by taking into account the worst-case timing paths, operating conditions, and process variations. Timing speculation based reliable overclocking advocates going beyond worst-case limits to achieve best performance while not avoiding, but detecting and correcting a modest number of timing errors. The success of this design methodology relies on the fact that timing critical paths are rarely exercised in a design, and typical execution happens much faster than the timing requirements dictated by worst-case design methodology. Better-than-worst-case design methodology is advocated by several recent research pursuits, which exploit dependability techniques to enhance computer system performance. In this dissertation, we address different aspects of timing speculation based adaptive reliable overclocking schemes, and evaluate their role in the design of low-cost, high performance, energy efficient and dependable systems. We visualize various control knobs in the design that can be favorably controlled to ensure different design targets. As part of this research, we extend the SPRIT3E, or Superscalar PeRformance Improvement Through Tolerating Timing Errors, framework, and characterize the extent of application dependent performance acceleration achievable in superscalar processors by scrutinizing the various parameters that impact the operation beyond worst-case limits. We study the limitations imposed by short-path constraints on our technique, and present ways to exploit them to maximize performance gains. We analyze the sensitivity of our technique\u27s adaptiveness by exploring the necessary hardware requirements for dynamic overclocking schemes. Experimental analysis based on SPEC2000 benchmarks running on a SimpleScalar Alpha processor simulator, augmented with error rate data obtained from hardware simulations of a superscalar processor, are presented. Even though reliable overclocking guarantees functional correctness, it leads to higher power consumption. As a consequence, reliable overclocking without considering on-chip temperatures will bring down the lifetime reliability of the chip. In this thesis, we analyze how reliable overclocking impacts the on-chip temperature of a microprocessor and evaluate the effects of overheating, due to such reliable dynamic frequency tuning mechanisms, on the lifetime reliability of these systems. We then evaluate the effect of performing thermal throttling, a technique that clamps the on-chip temperature below a predefined value, on system performance and reliability. Our study shows that a reliably overclocked system with dynamic thermal management achieves 25% performance improvement, while lasting for 14 years when being operated within 353K. Over the past five decades, technology scaling, as predicted by Moore\u27s law, has been the bedrock of semiconductor technology evolution. The continued downscaling of CMOS technology to deep sub-micron gate lengths has been the primary reason for its dominance in today\u27s omnipresent silicon microchips. Even as the transition to the next technology node is indispensable, the initial cost and time associated in doing so presents a non-level playing field for the competitors in the semiconductor business. As part of this thesis, we evaluate the capability of speculative reliable overclocking mechanisms to maximize performance at a given technology level. We evaluate its competitiveness when compared to technology scaling, in terms of performance, power consumption, energy and energy delay product. We present a comprehensive comparison for integer and floating point SPEC2000 benchmarks running on a simulated Alpha processor at three different technology nodes in normal and enhanced modes. Our results suggest that adopting reliable overclocking strategies will help skip a technology node altogether, or be competitive in the market, while porting to the next technology node. Reliability has become a serious concern as systems embrace nanometer technologies. In this dissertation, we propose a novel fault tolerant aggressive system that combines soft error protection and timing error tolerance. We replicate both the pipeline registers and the pipeline stage combinational logic. The replicated logic receives its inputs from the primary pipeline registers while writing its output to the replicated pipeline registers. The organization of redundancy in the proposed Conjoined Pipeline system supports overclocking, provides concurrent error detection and recovery capability for soft errors, intermittent faults and timing errors, and flags permanent silicon defects. The fast recovery process requires no checkpointing and takes three cycles. Back annotated post-layout gate-level timing simulations, using 45nm technology, of a conjoined two-stage arithmetic pipeline and a conjoined five-stage DLX pipeline processor, with forwarding logic, show that our approach, even under a severe fault injection campaign, achieves near 100% fault coverage and an average performance improvement of about 20%, when dynamically overclocked

Optimizing construction of scheduled data flow graph for on-line testability

The objective of this work is to develop a new methodology for behavioural synthesis using a flow of synthesis, better suited to the scheduling of independent calculations and non-concurrent online testing. The traditional behavioural synthesis process can be defined as the compilation of an algorithmic specification into an architecture composed of a data path and a controller. This stream of synthesis generally involves scheduling, resource allocation, generation of the data path and controller synthesis. Experiments showed that optimization started at the high level synthesis improves the performance of the result, yet the current tools do not offer synthesis optimizations that from the RTL level. This justifies the development of an optimization methodology which takes effect from the behavioural specification and accompanying the synthesis process in its various stages. In this paper we propose the use of algebraic properties (commutativity, associativity and distributivity) to transform readable mathematical formulas of algorithmic specifications into mathematical formulas evaluated efficiently. This will effectively reduce the execution time of scheduling calculations and increase the possibilities of testability

PRITEXT: Processor Reliability Improvement Through Exercise Technique

With continuous improvements in CMOS technology, transistor sizes are shrinking aggressively every year. Unfortunately, such deep submicron process technologies are severely degraded by several wearout mechanisms which lead to prolonged operational stress and failure. Negative Bias Temperature Instability (NBTI) is a prominent failure mechanism which degrades the reliability of current semiconductor devices. Improving reliability of processors is necessary for ensuring long operational lifetime which obviates the necessity of mitigating the physical wearout mechanisms. NBTI severely degrades the performance of PMOS transistors in a circuit, when negatively biased, by increasing the threshold voltage leading to critical timing failures over operational lifetime. A lack of activity among the PMOS transistors for long duration leads to a steady increase in threshold voltage Vth. Interestingly, NBTI stress can be recovered by removing the negative bias using appropriate input vectors. Exercising the dormant critical components in the Processor has been proved to reduce the NBTI stress. We use a novel methodology to generate a minimal set of deterministic input vectors which we show to be effective in reducing the NBTI wearout in a superscalar processor core. We then propose and evaluate a new technique PRITEXT, which uses these input vectors in exercise mode to effectively reduce the NBTI stress and improve the operational lifetime of superscalar processors. PRITEXT, which uses Input Vector Control, leads to a 4.5x lifetime improvement of superscalar processor on average with a maximum lifetime improvement of 12.7x

Evolution of Test Programs Exploiting a FSM Processor Model

Microprocessor testing is becoming a challenging task, due to the increasing complexity of modern architectures. Nowadays, most architectures are tackled with a combination of scan chains and Software-Based Self-Test (SBST) methodologies. Among SBST techniques, evolutionary feedback-based ones prove effective in microprocessor testing: their main disadvantage, however, is the considerable time required to generate suitable test programs. A novel evolutionary-based approach, able to appreciably reduce the generation time, is presented. The proposed method exploits a high-level representation of the architecture under test and a dynamically built Finite State Machine (FSM) model to assess fault coverage without resorting to time-expensive simulations on low-level models. Experimental results, performed on an OpenRISC processor, show that the resulting test obtains a nearly complete fault coverage against the targeted fault mode

Contention-aware performance monitoring counter support for real-time MPSoCs

Tasks running in MPSoCs experience contention delays when accessing MPSoC’s shared resources, complicating task timing analysis and deriving execution time bounds. Understanding the Actual Contention Delay (ACD) each task suffers due to other corunning tasks, and the particular hardware shared resources in which contention occurs, is of prominent importance to increase confidence on derived execution time bounds of tasks. And, whenever those bounds are violated, ACD provides information on the reasons for overruns. Unfortunately, existing MPSoC designs considered in real-time domains offer limited hardware support to measure tasks’ ACD losing all these potential benefits. In this paper we propose the Contention Cycle Stack (CCS), a mechanism that extends performance monitoring counters to track specific events that allow estimating the ACD that each task suffers from every contending task on every hardware shared resource. We build the CCS using a set of specialized low-overhead Performance Monitoring Counters for the Cobham Gaisler GR740 (NGMP) MPSoC – used in the space domain – for which we show CCS’s benefits.The research leading to these results has received funding from the European Space Agency under contracts 4000109680, 4000110157 and NPI 4000102880, and the Ministry of Science and Technology of Spain under contract TIN-2015-65316-P. Jaume Abella has been partially supported by the Ministry of Economy and Competitiveness under Ramon y Cajal postdoctoral fellowship number RYC-2013-14717.Peer ReviewedPostprint (author's final draft

New techniques for functional testing of microprocessor based systems

Electronic devices may be affected by failures, for example due to physical defects. These defects may be introduced during the manufacturing process, as well as during the normal operating life of the device due to aging. How to detect all these defects is not a trivial task, especially in complex systems such as processor cores. Nevertheless, safety-critical applications do not tolerate failures, this is the reason why testing such devices is needed so to guarantee a correct behavior at any time. Moreover, testing is a key parameter for assessing the quality of a manufactured product. Consolidated testing techniques are based on special Design for Testability (DfT) features added in the original design to facilitate test effectiveness. Design, integration, and usage of the available DfT for testing purposes are fully supported by commercial EDA tools, hence approaches based on DfT are the standard solutions adopted by silicon vendors for testing their devices. Tests exploiting the available DfT such as scan-chains manipulate the internal state of the system, differently to the normal functional mode, passing through unreachable configurations. Alternative solutions that do not violate such functional mode are defined as functional tests. In microprocessor based systems, functional testing techniques include software-based self-test (SBST), i.e., a piece of software (referred to as test program) which is uploaded in the system available memory and executed, with the purpose of exciting a specific part of the system and observing the effects of possible defects affecting it. SBST has been widely-studies by the research community for years, but its adoption by the industry is quite recent. My research activities have been mainly focused on the industrial perspective of SBST. The problem of providing an effective development flow and guidelines for integrating SBST in the available operating systems have been tackled and results have been provided on microprocessor based systems for the automotive domain. Remarkably, new algorithms have been also introduced with respect to state-of-the-art approaches, which can be systematically implemented to enrich SBST suites of test programs for modern microprocessor based systems. The proposed development flow and algorithms are being currently employed in real electronic control units for automotive products. Moreover, a special hardware infrastructure purposely embedded in modern devices for interconnecting the numerous on-board instruments has been interest of my research as well. This solution is known as reconfigurable scan networks (RSNs) and its practical adoption is growing fast as new standards have been created. Test and diagnosis methodologies have been proposed targeting specific RSN features, aimed at checking whether the reconfigurability of such networks has not been corrupted by defects and, in this case, at identifying the defective elements of the network. The contribution of my work in this field has also been included in the first suite of public-domain benchmark networks